-
Notifications
You must be signed in to change notification settings - Fork 0
qos_ecn_config_test
Verify QoS ECN feature configuration.
-
Connect DUT port-1 to ATE port-1, DUT port-2 to ATE port-2.
-
ECN configuration paramentes:
-
This test is verifying DUT ability to accept ECN configuration with vertical buffer utilization cut-off line.\ If buffer is utilized below that cut-off value no packet is ECN CE marked.\ If buffer is utilized at of above that cut-off value all packet are ECN CE marked.
-
ECN profile can be created for different queues. ECN profiles per queue can be applied to the output side of interfaces.
Test case min-threshold max-threshold enable-ecn drop weight max-drop-probability-percent #1 80KB 80KB true false not set 100 [TODO]#2 3.125MB 6.250MB* true false not set 100 [TODO]#3 1% 2% true false not set 100 -
6.25MB max-treshhold is selected as it represents ~500 mico-seconds of Delay bandwidth Buffer on 100GE interfaces. What is O(2%) of buffer depth, hence allows for micro-burst absorbtion without beackpressing senders and at same time leaves enough DBB for accomodate RTT ECN signaling loop delay in global network for longer burst/congestion.
-
-
Procedure
- Test Case #1 80KB min-threshold equal max-threshold
- Configute queue-management-profile w/ ECN paramenters as above. Attach to queue on DUT-Port1.
- Validate that the following values are set as expected using OC telemetry.
- min-threshold
- max-threshold
- min-threshold = max-threshold (vertical cut-off line)
- enable-ecn
- drop
- max-drop-probability-percent
- Validate ECN profile can be applied under output interface queue using OC telemetry.
- [TODO]Test Case #2 Treshold in MB, min-threshold not-equal max-threshold
- Configute queue-management-profile w/ ECN paramenters as above. Attach to queue on DUT-Port1.
- Validate that the following values are set as expected using OC telemetry.
- min-threshold
- max-threshold
- enable-ecn
- drop
- max-drop-probability-percent
- Validate ECN profile can be applied under output interface queue using OC telemetry.
- [TODO]Test Case #3 Treshold in percentage, min-threshold not-equal max-threshold
- Configute queue-management-profile w/ ECN paramenters as above. Attach to queue on DUT-Port1.
- Validate that the following values are set as expected using OC telemetry.
- min-threshold-percent
- max-threshold-percent
- enable-ecn
- drop
- max-drop-probability-percent
- Validate ECN profile can be applied under output interface queue using OC telemetry.
- Test Case #1 80KB min-threshold equal max-threshold
-
ECN
- [TODO] qos/queue-management-profiles/queue-management-profile/wred/uniform/config/min-threshold-percent
- [TODO] qos/queue-management-profiles/queue-management-profile/wred/uniform/config/max-threshold-percent
- qos/queue-management-profiles/queue-management-profile/wred/uniform/config/min-threshold
- qos/queue-management-profiles/queue-management-profile/wred/uniform/config/max-threshold
- qos/queue-management-profiles/queue-management-profile/wred/uniform/config/enable-ecn
- qos/queue-management-profiles/queue-management-profile/wred/uniform/config/weight
- qos/queue-management-profiles/queue-management-profile/wred/uniform/config/drop
- qos/queue-management-profiles/queue-management-profile/wred/uniform/config/max-drop-probability-percent
-
Interfaces
- /qos/interfaces/interface/input/classifiers/classifier/config/name
- /qos/interfaces/interface/output/queues/queue/config/name
- /qos/interfaces/interface/output/queues/queue/config/queue-management-profile
-
ECN
- [TODO] qos/queue-management-profiles/queue-management-profile/wred/uniform/state/min-threshold-percent
- [TODO] qos/queue-management-profiles/queue-management-profile/wred/uniform/state/max-threshold-percent
- qos/queue-management-profiles/queue-management-profile/wred/uniform/state/min-threshold
- qos/queue-management-profiles/queue-management-profile/wred/uniform/state/max-threshold
- qos/queue-management-profiles/queue-management-profile/wred/uniform/state/enable-ecn
- qos/queue-management-profiles/queue-management-profile/wred/uniform/state/weight
- qos/queue-management-profiles/queue-management-profile/wred/uniform/state/drop
- qos/queue-management-profiles/queue-management-profile/wred/uniform/state/max-drop-probability-percent
-
Interfaces
- /qos/interfaces/interface/input/classifiers/classifier/state/name
- /qos/interfaces/interface/output/queues/queue/state/name
- /qos/interfaces/interface/output/queues/queue/state/queue-management-profile
- vRX
-
Home
- Test Plans
- Authz: General Authz (1-4) tests
- CNTR-2: Container network connectivity tests
- DP-1.2: QoS policy feature config
- DP-1.3: QoS ECN feature config
- DP-1.4: QoS Interface Output Queue Counters
- DP-1.7: One strict priority queue traffic test
- DP-1.8: Two strict priority queue traffic test
- DP-1.9: WRR traffic test
- DP-1.10: Mixed strict priority and WRR traffic test
- DP-1.11: Bursty traffic test
- DP-1.14: QoS basic test
- example-0.1: Topology Test
- FP-1.1: Power admin DOWN/UP Test
- gNMI-1.1: cli Origin
- gNMI-1.2: Benchmarking: Full Configuration Replace
- gNMI-1.3: Benchmarking: Drained Configuration Convergence Time
- gNMI-1.4: Telemetry: Inventory
- gNMI-1.5: Telemetry: Port Speed Test
- gNMI-1.8: Configuration Metadata-only Retrieve and Replace
- gNMI-1.9: Get requests
- gNMI-1.10: Telemetry: Basic Check
- gNMI-1.11: Telemetry: Interface Packet Counters
- gNMI-1.12: Mixed OpenConfig/CLI Origin
- gNMI-1.13: Optics Telemetry, Instant, threshold, and miscellaneous static info
- gNMI-1.14: OpenConfig metadata consistency during large config push
- gNMI-1.15: Set Requests
- gNMI-1.16: fabric redundancy test
- gNMI-1.17: Controller Card redundancy test
- gNMI-1.18: gNMI subscribe with sample mode for backplane capacity counters
- gNMI-1.19: ConfigPush after Control Card switchover
- gNMI-1.20: Telemetry: Optics Thresholds
- gNMI-1.21: Integrated Circuit Hardware Resource Utilization Test
- gNMI-1.22: Controller card port attributes
- gNMI-1.27: gNMI Sample Mode Test
- gNOI-2.1: Packet-based Link Qualification
- gNOI-3.1: Complete Chassis Reboot
- gNOI-3.2: Per-Component Reboot
- gNOI-3.3: Supervisor Switchover
- gNOI-3.4: Chassis Reboot Status and Reboot Cancellation
- gNOI-4.1: Software Upgrade
- gNOI-5.1: Ping Test
- gNOI-5.2: Traceroute Test
- gNOI-5.3: Copying Debug Files
- gNOI-6.1: Factory Reset
- Health-1.1: Generic Health Check
- Health-1.2: Healthz component status paths
- MGT-1: Management HA solution test
- MTU-1.3: Large IP Packet Transmission
- OC-1.2: Default Address Families
- OC-26.1: Network Time Protocol (NTP)
- P4RT-1.1: Base P4RT Functionality
- P4RT-1.2: P4RT Daemon Failure
- P4RT-2.1: P4RT Election
- P4RT-2.2: P4RT Metadata Validation
- P4RT-3.1: Google Discovery Protocol: PacketIn
- P4RT-3.2: Google Discovery Protocol: PacketOut
- P4RT-5.1: Traceroute: PacketIn
- P4RT-5.2: Traceroute Packetout
- P4RT-6.1: Required Packet I/O rate: Performance
- P4RT-7.1: LLDP: PacketIn
- P4RT-7.2: LLDP: PacketOut
- Replay-1.0: Record/replay presession test
- Replay-1.1: Record/replay diff command trees test
- Replay-1.2: P4RT Replay Test
- RT-1.1: Base BGP Session Parameters
- RT-1.2: BGP Policy & Route Installation
- RT-1.3: BGP Route Propagation
- RT-1.4: BGP Graceful Restart
- RT-1.5: BGP Prefix Limit
- RT-1.7: Local BGP Test
- RT-1.10: BGP Keepalive and HoldTimer Configuration Test
- RT-1.11: BGP remove private AS
- RT-1.12: BGP always compare MED
- RT-1.14: BGP Long-Lived Graceful Restart
- RT-1.19: BGP 2-Byte and 4-Byte ASN support
- RT-1.21: BGP TCP MSS and PMTUD
- RT-1.23: BGP AFI SAFI OC DEFAULTS
- RT-1.24: BGP 2-Byte and 4-Byte ASN support with policy
- RT-1.25: Management network-instance default static route
- RT-1.26: Basic static route support
- RT-1.27: Static route to BGP redistribution
- RT-1.28: BGP to IS-IS redistribution
- RT-1.29: BGP chained import/export policy attachment
- RT-1.30: BGP nested import/export policy attachment
- RT-1.32: BGP policy actions - MED, LocPref, prepend, flow-control
- RT-1.33: BGP Policy with prefix-set matching
- RT-1.51: BGP multipath ECMP
- RT-1.52: BGP multipath UCMP support with Link Bandwidth Community
- RT-2.1: Base IS-IS Process and Adjacencies
- RT-2.2: IS-IS LSP Updates
- RT-2.6: IS-IS Hello-Padding enabled at interface level
- RT-2.7: IS-IS Passive is enabled at interface level
- RT-2.8: IS-IS metric style wide not enabled
- RT-2.9: IS-IS metric style wide enabled
- RT-2.10: IS-IS change LSP lifetime
- RT-2.11: IS-IS Passive is enabled at the area level
- RT-2.12: Static route to IS-IS redistribution
- RT-2.13: Weighted-ECMP for IS-IS
- RT-2.14: IS-IS Drain Test
- RT-3.1: Policy based VRF selection
- RT-3.2: Multiple <Protocol, DSCP> Rules for VRF Selection
- RT-4.10: AFTs Route Summary
- RT-5.1: Singleton Interface
- RT-5.2: Aggregate Interfaces
- RT-5.3: Aggregate Balancing
- RT-5.4: Aggregate Forwarding Viable
- RT-5.5: Interface hold-time
- RT-5.6: Interface Loopback mode
- RT-5.8: IPv6 Link Local
- RT-5.9: Disable IPv6 ND Router Arvetisment
- RT-5.10: IPv6 Link Local generated by SLAAC
- RT-6.1: Core LLDP TLV Population
- RT-7.1: BGP default policies
- RT-7.2: BGP Policy Community Set
- RT-7.3: BGP Policy AS Path Set
- RT-7.4: BGP Policy AS Path Set and Community Set
- RT-7.5: BGP Policy - Match and Set Link Bandwidth Community
- RT-7.8: BGP Policy Match Standard Community and Add Community Import/Export Policy
- RT-7.11: BGP Policy - Import/Export Policy Action Using Multiple Criteria
- SEC-3.1: Authentication
- SFLOW-1: sFlow Configuration and Sampling
- System-1: System testing
- TE-1.1: Static ARP
- TE-1.2: My Station MAC
- TE-2.1: gRIBI IPv4 Entry
- TE-2.2: gRIBI IPv4 Entry With Aggregate Ports
- TE-3.1: Base Hierarchical Route Installation
- TE-3.2: Traffic Balancing According to Weights
- TE-3.3: Hierarchical weight resolution
- TE-3.5: Ordering: ACK Received
- TE-3.6: ACK in the Presence of Other Routes
- TE-3.7: Base Hierarchical NHG Update
- TE-3.31: Hierarchical weight resolution with PBF
- TE-4.1: Base Leader Election
- TE-4.2: Persistence Mode
- TE-5.1: gRIBI Get RPC
- TE-6.1: Route Removal via Flush
- TE-6.2: Route Removal In Non Default VRF
- TE-8.1: DUT Daemon Failure
- TE-8.2: Supervisor Failure
- TE-9.1: FIB FAILURE DUE TO HARDWARE RESOURCE EXHAUST
- TE-9.2: MPLS based forwarding Static LSP
- TE-9: gRIBI MPLS Compliance
- TE-10: gRIBI MPLS Forwarding
- TE-11.1: Backup NHG: Single NH
- TE-11.2: Backup NHG: Multiple NH
- TE-11.3: Backup NHG: Actions
- TE-11.21: Backup NHG: Multiple NH with PBF
- TE-11.31: Backup NHG: Actions with PBF
- TE-13.1: gRIBI route ADD during Failover
- TE-13.2: gRIBI route DELETE during Failover
- TE-14.1: gRIBI Scaling
- TE-14.2: encap and decap scale
- TE-15.1: gRIBI Compliance
- TE-16.1: basic encapsulation tests
- TE-16.2: encapsulation FRR scenarios
- TE-17.1: VRF selection policy driven TE
- TR-6.1: Remote Syslog feature config
- TRANSCEIVER-1: Telemetry: 400ZR Chromatic Dispersion(CD) telemetry values streaming
- TRANSCEIVER-3: Telemetry: 400ZR Optics firmware version streaming
- TRANSCEIVER-4: Telemetry: 400ZR RX input and TX output power telemetry values streaming.
- TRANSCEIVER-5: Configuration: 400ZR channel frequency, output TX launch power and operational mode setting.
- TRANSCEIVER-6: Telemetry: 400ZR Optics performance metrics (pm) streaming.
- TRANSCEIVER-7: Telemetry: 400ZR Optics inventory info streaming
- TRANSCEIVER-8: Telemetry: 400ZR Optics module temperature streaming.
- TRANSCEIVER-9: Telemetry: 400ZR TX laser bias current telemetry values streaming.
- TRANSCEIVER-10: Telemetry: 400ZR Optics FEC(Forward Error Correction) Uncorrectable Frames Streaming.
- TRANSCEIVER-11: Telemetry: 400ZR Optics logical channels provisioning and related telemetry.
- TRANSCEIVER-12: Telemetry: 400ZR Transceiver Supply Voltage streaming.
- TRANSCEIVER-13: Configuration: 400ZR Transceiver Low Power Mode Setting.
- TUN-1.4: Interface based IPv6 GRE Encapsulation
- TUN-1.9: GRE inner packet DSCP
- Test Plans