Mazda
Changing source code, using weighted lockout mitigation or changing EPS is all done at your own risk.
The Mazda community is strong, and most Mazda models are community supported with limitations. Out of the box, only CX-5 2022 and CX-9 2021 is officially supported. For all other models openpilot is only available in dashcam mode due to a steering lockout that occurs when driver does not touch the steering wheel for more than 5 seconds. Using Stock openpilot with Mazda models that have limitations requires source code changes, and always keeping your hands on the wheel or use of a weighted steering lockout mitigation or changing Electronic Power Steering motor (EPS) to 2021 CX-9 where compatible. Failure to overcome the steering lockout results in the car not responding to steer commands from openpilot.
To change source code from dashcam only mode, change the line in selfdrive/car/mazda/interface.py [here]
from:
ret.dashcamOnly = candidate not in [CAR.CX9_2021]
to
ret.dashcamOnly = False
If you don't want to make source code change, you can use Mazda community fork, see the link at the bottom of this page.
For general terms, go here.
Mazda I-ACTIVSENSE is an umbrella term that Mazda uses to describe a series of advanced safety and driver assistance technologies such as ACC, LKAS, Blind-spot monitoring, Smart City brakes and so on. Most models/trims from 2017 and newer come with ACC and LKAS as standard options.
| Term | Abbreviation | Definition |
|---|---|---|
| Mazda Radar Cruise Control | MRCC | Mazda Adaptive Cruise Control - ACC |
| Lane-Keep Assist System | LAS | Mazda LKAS |
Official Community Supported Models
- 2021 CX-9
- 2022 CX-5
Community Supported Models with Limitation
- 2017-2020 CX-9 (2019 and 2020 models have twice the torque compared to earlier years)
- 2017-2021 Mazda 6, and CX-5
- 2017-2018 Mazda 3
-
- 2019 Mazda 3 / CX-30 and newer use a new driver assistance system and is not yet supported, comma connector is not correct
- 2017-2020 CX-3 (needs confirmation)
Note: Some earlier year models 2016-2017 models that are equipped with LKAS are known to work with the Community fork but may require a different connector than the Mazda development connector sold at comma shop.
Mazda LKAS is not available on low speeds. In particular, LKAS is not available until the car drives above 32mph/52kph. LKAS gets disabled when the speed goes below 28mpg/45kph. When OP is engaged but stock LKAS is not available, OP continues to be engaged but will not steer and will display a warning about steering being unavailable.
CX-9 2019-2021 offer the best torque among Mazda cars. They offer twice the torque compared to other models/years allowing them to make tighter turns even on city streets. For other cars the available steering torque is adequate for most highway driving conditions. City driving requires driver intervention on sharp turns.
- LKAS is allowed when the car drives above 32mph
- LKAS is not allowed when the speed dips below 28mph
Longitudinal control is not supported by OP with Mazda. OP relies on the stock MRCC to control speed. MRCC support follow-to-stop to 0mph and automatic resume if the stop is less than three seconds. OP improve on that by allowing the car to resume without driver intervention after longer delays. Even though MRCC works down to 0mph, the lowest allowed set speed is 19mph.
Note: Mazda harness is now available at comma shop. Look for "Mazda Development" when you select a vehicle.
Harness wiring:
- Steer down to zero
- Steer without lockout
- openpilot longitudinal control