Fix HomeSeer products configuration (user manual urls, parameter 19 f…

…or HS-MS100+, and typos)

packages/config/config/devices/0x000c/hs-ds100.json

@@ -32,6 +32,6 @@
 		"inclusion": "1. Insert the AAA battery.\n2. Set the Z-Wave network main controller into learning mode.\n3. Triple or single short press the Z-button.\n4. If the add for inclusion is successful, the LED will blink less than 5 seconds and then keep on 3 seconds. Otherwise, the LED will blink 5 seconds and then turn off, in which case you need to repeat the process from step 2.",
 		"exclusion": "1. Insert the AAA battery.\n2. Set the Z-Wave network main controller into learning mode.\n3. Triple clicking the Z-button.\n4. If the remove for exclusion, the LED will turn off within 1 second. Otherwise, the LED will blink 5 seconds and then turn off, in which case you need to repeat the process from step 2.",
 		"reset": "1. Insert the AAA battery.\n2. Pressing and holding the Z button for more than 20 seconds,\n3. Led will keep on until the Z-Button is released, and it will reset to factory default when the button is released.\n\nUsing this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2148/HS-DS100-Manual.pdf"
+		"manual": "https://docs.homeseer.com/products/hs-ds100-user-guide"
 	}
 }

packages/config/config/devices/0x000c/hs-fc200.json

@@ -85,6 +85,6 @@
 		"inclusion": "Inclusion: Add the device into your network by a Z-Wave certified controller. HS-FC200+ supports the latest S2 security offered by Z-Wave certified controllers. If your controller supports S2, please refer to the user guide of the controller for detailed instructions on adding devices to the network. You should be able to add HS-FC200+ into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added or removed using the following 2-step procedure:\n\n1. Put your Z-Wave controller into Inclusion mode. Consult your controller manual if you're unsure how to do this.\n2. Tap the paddle of your new HomeSeer switch to begin the inclusion process. This will take a few moments to complete",
 		"exclusion": "Exclusion: Remove the device from your network by a Z-Wave certified controller. HS-FC200+ supports the latest S2 security offered by Z-Wave certified controllers. If your controller supports S2, please refer to the user guide of the controller for detailed instructions on removing devices from the network. You should be able to remove HS-FC200+ into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added or removed using the following 2-step procedure:\n\n1. Put your Z-Wave controller into Exclusion mode. Consult your controller manual if you're unsure how to do this.\n2. Tap the paddle of your new HomeSeer switch to begin the Exclusion process. This will take a few moments to complete",
 		"reset": "To be used only in the event that the network primary controller is lost or otherwise inoperable. \n\n(1) Turn switch on by tapping the top of the paddle once. \n(2) Quickly ap top of the paddle 3 times. \n(3) Quickly tap bottom of paddle 3 times. \n(4) If the LED turns off then on again, switch is reset. If not, repeat manual rest.",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2957/HS%20FC200%20Manual%20Market%20Cert%20v1.pdf"
+		"manual": "https://homeseer.com/guides/HS-FC200-Manual.pdf"
 	}
 }

packages/config/config/devices/0x000c/hs-fls100-g2.json

@@ -101,6 +101,6 @@
 		"inclusion": "1. Put the Z-Wave controller into inclusion mode.\n2. Press the Link button 3 times within 1.5 seconds to put the unit into inclusion mode.",
 		"exclusion": "1. Put the Z-Wave Controller into exclusion mode. \n2. Press the Link button 3 times within 1.5 seconds to put the unit into exclusion mode",
 		"reset": "The product reset is to operate only when the primary controller is missing or inoperable. Press the Link button 3 times within 1.5 seconds to put the unit into exclusion mode.Within 1 second of step 1, press the Link button again and hold until LED is off (about 5 seconds)",
-		"manual": "https://docs.homeseer.com/products/sensors/hs-fls100+/hs-fls100+-user-guide"
+		"manual": "https://docs.homeseer.com/products/hs-fls100-user-guide"
 	}
 }

packages/config/config/devices/0x000c/hs-fs100_flex.json

@@ -46,6 +46,6 @@
 		"inclusion": "Inclusion: Add the device into your network by a Z-Wave certified controller. HS-FS100+ supports the latest S2 security offered by Z-Wave certified controllers. If your controller supports S2, please refer to the user guide of the controller for detailed instructions on adding devices to the network. The device can be added using the traditional method for Z-Wave as follows:\n1. Place your controller into Inclusion (Add) mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button of HS-FS100+. The controller should indicate that the new device was added successfully. If the controller shows it failed, repeat the procedure",
 		"exclusion": "Exclusion: Remove the device from your network by a Z-Wave certified controller. HS-FS100+ supports the latest S2 security offered by Z-Wave certified controllers. If your controller supports S2, please refer to the user guide of the controller for detailed instructions on removing devices from the network. The device can be removed using the traditional method for Z-Wave as follows:\n1. Place your controller into Exclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button of HS-FS100+. The controller should indicate that the device was removed successfully. If the controller shows it failed, repeat the procedure",
 		"reset": "Use this procedure to reset Flex Sensor to factory settings when the Z-Wave controller is missing or otherwise inoperable.\n\nPress and hold the Z-Wave button on the sensor body for 10 seconds. If successful, the LED will flash 5 times",
-		"manual": "https://docs.homeseer.com/products/sensors/hs-fs100/hs-fs100+-user-guide"
+		"manual": "https://docs.homeseer.com/products/hs-fs100-user-guide"
 	}
 }

packages/config/config/devices/0x000c/hs-hsm200.json

@@ -2,7 +2,7 @@
 	"manufacturer": "HomeSeer Technologies",
 	"manufacturerId": "0x000c",
 	"label": "HS-HSM200",
-	"description": "Z-Wave Multi Sensorr",
+	"description": "Z-Wave Multi Sensor",
 	"devices": [
 		{
 			"productType": "0x0004",
@@ -96,6 +96,6 @@
 		"inclusion": "1) Place the device within the direct range of your Z-Wave controller.\n2) Set the main controller in add mode (see the controller’s manual).\n3) Click the button on the side of the unit once, the LED indicator should start blinking blue. \n4) Wait for the adding process to end.\n5) Successful adding will be confirmed by the Z-Wave controller’s message.",
 		"exclusion": "1) Place the device within the direct range of your Z-Wave controller.\n2) Set the main controller remove mode (see the controller’s manual).\n3) Click the button on the side of the unit once\n4) Wait for the removing process to end.\n5) Successful adding will be confirmed by the Z-Wave controller’s message.",
 		"reset": "1) Power on the device\n2) Press and hold the side button for 60 seconds.\n2) Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
-		"manual": "https://docs.homeseer.com/products/sensors/hsm200/hsm200-user-guide"
+		"manual": "https://docs.homeseer.com/products/hsm200-user-guide"
 	}
 }

packages/config/config/devices/0x000c/hs-ls100.json

@@ -77,6 +77,6 @@
 		"inclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller in add mode (see the controller’s manual).\n4) Click the Z-button once (non-secure inclusion) or triple click (secure inclusion) the Z-button quickly, the LED indicator should blink fast. \n5) Wait for the adding process to end.\n6) Successful adding will be confirmed by the Z-Wave controller’s message.",
 		"exclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller remove mode (see the controller’s manual).\n4) Triple click the Z-button quickly, the LED indicator should blink fast.\n5) Wait for the removing process to end.\n6) Successful adding will be confirmed by the Z-Wave controller’s message.",
 		"reset": "1) Power on the device\n2) Press and hold the Z button for more than 20 seconds,\n3) If holding time more than 20seconds, the LED indicator will keep on for 2 seconds, which means resetting is complete.\n4) The reset feature works only when the device has been included into a Z-Wave network.\n\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
-		"manual": "https://docs.homeseer.com/products/sensors/hs-ls100+/hs-ls100+-user-guide"
+		"manual": "https://docs.homeseer.com/products/hs-ls100-user-guide"
 	}
 }

packages/config/config/devices/0x000c/hs-ms100.json

@@ -54,7 +54,9 @@
 		},
 		{
 			"#": "19",
-			"$import": "templates/homeseer_template.json#enable_basic_set_command"
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Enable / Disable Binary Sensor for Motion",
+			"defaultValue": 1
 		},
 		{
 			"#": "32",
@@ -65,6 +67,6 @@
 		"inclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller in add mode (see the controller’s manual).\n4) Click the Z-button once, the LED indicator should blink fast. \n5) Wait for the adding process to end.\n6) Successful adding will be confirmed by the Z-Wave controller’s message.",
 		"exclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller remove mode (see the controller’s manual).\n4) Triple click the Z-button quickly, the LED indicator should blink fast.\n5) Wait for the removing process to end.\n6) Successful adding will be confirmed by the Z-Wave controller’s message.",
 		"reset": "1)Power on the device,\n2) Press and hold the Z button for more than 20 seconds,\n3) If holding time more than 20seconds, the LED indicator will keep on for 2 seconds, which means resetting is complete.\n4) The reset feature works only when the device has been included into a Z-Wave network.\n\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2729/User%20Manual%20for%20motion%20sensor-revised%20.pdf"
+		"manual": "https://docs.homeseer.com/products/hs-ms100-user-guide"
 	}
 }

packages/config/config/devices/0x000c/hs-wd100.json

@@ -58,6 +58,6 @@
 		"inclusion": "1. Turn the connected lights ON/OFF by tapping the switch. Tapping and releasing the upper part of the rocker turns the appliance ON. Tapping and releasing the lower part of the rocker turns the appliance OFF.\n2. Add(Include) the module to/from your Z-Wave network with your primary controller. Please refer to the instructions manual of your gateway or remote controller for details and procedures on how these actions can be done. \n3. Normally, the sequence is as follows: when the inclusion process is prompted by your primary controller, single click and release the rocker switch to ON or OFF position. The controller should show that the action was successful. If the controller shows it was a fail, repeat the procedure",
 		"exclusion": "1. Turn the connected appliance ON/OFF by tapping the switch. Tapping and releasing the upper part of the rocker turns the appliance ON. Tapping and releasing the lower part of the rocker turns the appliance OFF.\n2. Delete(Exclude) the module to/from your Z-Wave network with your primary controller. Please refer to the instructions manual of your gateway or remote controller for details and procedures on how these actions can be done. \n3. Normally, the sequence is as follows: when the exclusion process is prompted by your primary controller, single click and release the rocker switch. The controller should show that the action was successful. If the controller shows it was a fail, repeat the procedure",
 		"reset": "Please use this procedure only in the event that the network primary controller is lost or otherwise inoperable.\n\nAll Configuration Parameters can all be restored to their factory default settings by using your primary controller to delete/reset the device. \nTo manually reset, tap the ON button twice quickly and then tap the OFF button twice quickly. Repeat the procedure to restore the settings to the factory default.",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2563/HS-WD100-Manual-v1_1a.pdf"
+		"manual": "https://homeseer.com/guides/HS-WD100-Manual-7.pdf"
 	}
 }

packages/config/config/devices/0x000c/hs-wd200.json

@@ -142,6 +142,6 @@
 		"inclusion": "1. Turn the connected lights ON/OFF by tapping the switch. Tapping and releasing the upper part of the rocker turns the appliance ON. Tapping and releasing the lower part of the rocker turns the appliance OFF.\n2. Add(Include) the module to/from your Z-Wave network with your primary controller. Please refer to the instructions manual of your gateway or remote controller for details and procedures on how these actions can be done. \n3. Normally, the sequence is as follows: when the inclusion process is prompted by your primary controller, single click and release the rocker switch to ON or OFF position. The controller should show that the action was successful. If the controller shows it was a fail, repeat the procedure",
 		"exclusion": "1. Turn the connected appliance ON/OFF by tapping the switch. Tapping and releasing the upper part of the rocker turns the appliance ON. Tapping and releasing the lower part of the rocker turns the appliance OFF.\n2. Delete(Exclude) the module to/from your Z-Wave network with your primary controller. Please refer to the instructions manual of your gateway or remote controller for details and procedures on how these actions can be done. \n3. Normally, the sequence is as follows: when the exclusion process is prompted by your primary controller, single click and release the rocker switch. The controller should show that the action was successful. If the controller shows it was a fail, repeat the procedure",
 		"reset": "Please use this procedure only in the event that the network primary controller is lost or otherwise inoperable.\n\nAll Configuration Parameters can all be restored to their factory default settings by using your primary controller to delete/reset the device. \nTo manually reset: (1) Turn dimmer on by tapping the top of the paddle once. (2) Quickly tap top of the paddle 3 times. (3) Quickly tap bottom of paddle 3 times. (4) If light turns off and then on again, dimmer is reset. If not, repeat manual reset.",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2676/HS-WD200-Manual-4.pdf"
+		"manual": "https://homeseer.com/guides/HS-WD200-Manual.pdf"
 	}
 }

packages/config/config/devices/0x000c/hs-ws200.json

@@ -51,6 +51,6 @@
 		"inclusion": "1. Turn the connected appliance ON/OFF by tapping the switch. Tapping and releasing the upper part of the rocker turns the appliance ON. Tapping and releasing the lower part of the rocker turns the appliance OFF.\n2. Add(Include) the module to/from your Z-Wave network with your primary controller. Please refer to the instructions manual of your gateway or remote controller for details and procedures on how these actions can be done. \n3. Normally, the sequence is as follows: when the inclusion process is prompted by your primary controller, single click and release the rocker switch to ON or OFF position. The controller should show that the action was successful. If the controller shows it was a fail, repeat the procedure",
 		"exclusion": "1. Turn the connected appliance ON/OFF by tapping the switch. Tapping and releasing the upper part of the rocker turns the appliance ON. Tapping and releasing the lower part of the rocker turns the appliance OFF.\n2. Delete(Exclude) the module to/from your Z-Wave network with your primary controller. Please refer to the instructions manual of your gateway or remote controller for details and procedures on how these actions can be done. Normally, the sequence is as follows: when the exclusion process is prompted by your primary controller, single click and release the rocker switch. The controller should show that the action was successful. If the controller shows it was a fail, repeat the procedure",
 		"reset": "Please use this procedure only in the event that the network primary controller is lost or otherwise inoperable.\n\nAll Configuration Parameters can all be restored to their factory\ndefault settings by using your primary controller to delete/reset\nthe device. To manually reset, tap the ON button twice quickly and then tap the OFF button twice quickly. Repeat the procedure to restore the settings to the factory default.",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2675/HS-WS200-Manual-v4.pdf"
+		"manual": "https://homeseer.com/guides/HS-WS200-Manual.pdf"
 	}
 }

packages/config/config/devices/0x000c/hs-wv100.json

@@ -25,6 +25,6 @@
 		"inclusion": "How to Add the HS-WV100+ Z-Wave Valve Controller to your Z-Wave Controller\n- Plug the wall cube power adapter (included) into the receptacle on the bottom of the HS-WV100+ Z-Wave Valve Controller marked “3.6 VDC”. Plug the wall cube into a 110 VAC outlet. This provides power to the HS-WV100+ Z-Wave Valve Controller.\n- Configure the Z-Wave Controller to Add a device. \n- When the Z-Wave Controller is ready to add a device, it will display a message like “waiting to add device. Press Add button on the device”\n- The Add/Remove button is located on the side of the HS-WV100+ Z-Wave Valve Controller. Press the Add/Remove button.\n- The Z-Wave Controller will acknowledge that the HS-WV100+ Z-Wave Valve Controller had been added to the Z-Wave network.\n- Your HS-WV100+ Z-Wave Valve Controllerler is ready to use",
 		"exclusion": "How to Remove the HS-WV100+ Z-Wave Valve Controllerler to your Z-Wave Controller\n\n- Plug the wall cube power adapter (included) into the receptacle on the bottom of the HS-WV100+ Z-Wave Valve Controller marked “3.6 VDC”. Plug the wall cube into a 110 VAC outlet. This provides power to the HS-WV100+ Z-Wave Valve Controller.\n- Configure the Z-Wave Controller to Remove a device. \n- When the Z-Wave Controller is ready to Remove a device, it will display a message like “waiting to remove device. Press remove button on the device”\n- The Add/Remove button is located on the side of the HS-WV100+ Z-Wave Valve Controller. Press the Add/Remove button. \n- The Z-Wave Controller will acknowledge that the HS-WV100+ Z-Wave Valve Controller had been removed from the Z-Wave network.\n- Your HS-WV100+ Z-Wave Valve Controller is removed form this controller",
 		"reset": "How to reset the HS-WV100+ Z-Wave Valve Controller.\n- To reset the HS-WV100+ Z-Wave Valve Controller Z-Wave radio and routing table, press and hold the Add/Remove button located on the side of the HS-WV100+ Z-Wave Valve Control for 15 seconds. \n\nUse this procedure only when the network primary controller is missing or otherwise inoperable",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1845/HS-WV100-Manual.pdf"
+		"manual": "https://docs.homeseer.com/products/hs-wv100-user-guide"
 	}
 }