Base System Architecture

Base System Architecture (BSA) specification describes a hardware system architecture based on the Arm 64-bit architecture. System software such as operating systems, hypervisors, and firmware rely on this. It addresses PE features and key aspects of system architecture.

For more information, see BSA specification

BSA - Architecture Compliance Suite

BSA Architecture Compliance Suite (ACS) is a collection of self-checking, portable C-based tests. This suite includes a set of examples of the invariant behaviors that are provided by the BSA specification, so that you can verify if these behaviour have been interpreted correctly. Most of the tests are executed from UEFI (Unified Extensible Firmware Interface) Shell by executing the BSA UEFI shell application. A few tests are executed by running the BSA ACS Linux application which in turn depends on the BSA ACS Linux kernel module.

Release details

Code quality: v1.0
The tests are written for version 1.0 of the BSA specification.
The compliance suite is not a substitute for design verification.
To review the BSA ACS logs, Arm licensees can contact Arm directly through their partner managers.

GitHub branch

To pick up the release version of the code, checkout the corresponding tag from the main branch.
To get the latest version of the code with bug fixes and new features, use the main branch.

Additional reading

For information on the test scenarios currently implemented for platform using Device tree, see Scenario Document.
For information on the test scenarios currently implemented for platform using ACPI table, see Scenario Document.

ACS build steps - UEFI Shell application

Prebuilt images

Prebuilt images for each release are available in the prebuilt_images folder of the release branch. You can choose to use these images or build your own image by following the steps below. If you choose to use the prebuilt image, see the Test suite execution section below for details on how to run the application.

1. Building from source

Before you start the ACS build, ensure that the following requirements are met.

Any mainstream Linux-based OS distribution running on a x86 or AArch64 machine.
git clone the edk2-stable202102 tag of EDK2 tree.
git clone the EDK2 port of libc to local <edk2_path>.
GCC 7.5 or a later toolchain for Linux from here.
Install the build prerequisite packages to build EDK2. Note: The details of the packages are beyond the scope of this document.

1.1 Target Platform

To start the ACS build for platform using ACPI table, perform the following steps:

cd local_edk2_path
git submodule update --init --recursive
git clone https://github.com/ARM-software/bsa-acs.git ShellPkg/Application/bsa-acs
Add the following to the [LibraryClasses.common] section in ShellPkg/ShellPkg.dsc

     BsaValLib|ShellPkg/Application/bsa-acs/val/BsaValLib.inf
     BsaPalLib|ShellPkg/Application/bsa-acs/platform/pal_uefi_acpi/BsaPalLib.inf

Add the following in the [components] section of ShellPkg/ShellPkg.dsc

     ShellPkg/Application/bsa-acs/uefi_app/BsaAcs.inf

To start the ACS build for platform using Device tree, perform the following steps:

cd local_edk2_path
git submodule update --init --recursive
git clone https://github.com/ARM-software/bsa-acs.git ShellPkg/Application/bsa-acs
Add the following to the [LibraryClasses.common] section in ShellPkg/ShellPkg.dsc

     FdtLib|EmbeddedPkg/Library/FdtLib/FdtLib.inf
     BsaValLib|ShellPkg/Application/bsa-acs/val/BsaValLib.inf
     BsaPalLib|ShellPkg/Application/bsa-acs/platform/pal_uefi_dt/BsaPalLib.inf

Add the following in the [components] section of ShellPkg/ShellPkg.dsc

     ShellPkg/Application/bsa-acs/uefi_app/BsaAcs.inf

In IR systems, ACS efi application runs on top of efi shell which runs on u-boot as efi payload.

Below change in edk2 code MdeModulePkg/Library/UefiHiiServicesLib/UefiHiiServicesLib.c is required before compiling for IR system.

     -Status = gBS->LocateProtocol (&gEfiHiiConfigRoutingProtocolGuid, NULL, (VOID **) &gHiiConfigRouting);
     -ASSERT_EFI_ERROR (Status);
     +//Status = gBS->LocateProtocol (&gEfiHiiConfigRoutingProtocolGuid, NULL, (VOID **) &gHiiConfigRouting);
     +//ASSERT_EFI_ERROR (Status);

1.2 Build environment

If the build environment is Linux, perform the following steps:

export GCC49_AARCH64_PREFIX= GCC7.5 toolchain path pointing to /bin/aarch64-linux-gnu- in case of x86 machine. For an AArch64 build it should point to /usr/bin/
export PACKAGES_PATH= path pointing to edk2-libc
source edksetup.sh
make -C BaseTools/Source/C
source ShellPkg/Application/bsa-acs/tools/scripts/acsbuild.sh

1.3 Build output

The EFI executable file is generated at <edk2_path>/Build/Shell/DEBUG_GCC49/AARCH64/Bsa.efi

2. Test suite execution

Prerequisites

If the system supports LPIs (Interrupt ID > 8192) then Firmware should support installation of handler for LPI interrupts.
- If you are using edk2, change the ArmGic driver in the ArmPkg to support installation of handler for LPIs.
- Add the following in edk2/ArmPkg/Drivers/ArmGic/GicV3/ArmGicV3Dxe.c

   - After [#define ARM_GIC_DEFAULT_PRIORITY  0x80]
     +#define ARM_GIC_MAX_NUM_INTERRUPT 16384
   - Change this in GicV3DxeInitialize function.
     -mGicNumInterrupts      = ArmGicGetMaxNumInterrupts (mGicDistributorBase);
     +mGicNumInterrupts      = ARM_GIC_MAX_NUM_INTERRUPT;

The execution of the compliance suite varies depending on the test environment. The following steps assume that the test suite is invoked through the ACS UEFI shell application.

2.1 Silicon

On a system where a USB port is available and functional, perform the following steps:

For IR Systems:

Copy 'Bsa.efi' and 'Shell.efi' to a USB Flash drive.
Boot the system to U-Boot shell.
Plug in the USB flash drive to one of the functional USB ports on the system.
To determine the file system number of the plugged-in USB drive, execute command
usb start
Copy the 'Shell.efi' to memory location using the command
Syntax: fatload usb <dev_num> ${kernel_addr_r} Shell.efi
Eg: fatload usb 0 ${kernel_addr_r} Shell.efi
This boots the system to UEFI Shell.
To determine the file system number of the plugged-in USB drive, execute 'map -r' command.
Type 'fs' where '' is replaced by the number determined in step 5.
To start the compliance tests, run the executable Bsa.efi with the appropriate parameters.
Copy the UART console output to a log file. Note: 'Shell.efi' is available in the pebuilt_images/IR

2.2 Emulation environment with secondary storage

On an emulation environment with secondary storage, perform the following steps:

Create an image file which contains the 'Bsa.efi' file. For example:

mkfs.vfat -C -n HD0 hda.img 2097152
sudo mount -o rw,loop=/dev/loop0,uid=`whoami`,gid=`whoami` hda.img /mnt/bsa In case loop0 is busy, please specify the one that is free.
sudo cp "/Bsa.efi" /mnt/bsa/
sudo umount /mnt/bsa

Load the image file to the secondary storage using a backdoor. The steps to load the image file are emulation environment-specific and beyond the scope of this document.
Boot the system to UEFI shell.
To determine the file system number of the secondary storage, execute 'map -r' command.
Type 'fs' where '' is replaced by the number determined in step 4.
To start the compliance tests, run the executable Bsa.efi with the appropriate parameters.
Copy the UART console output to a log file for analysis and certification.

For information on the BSA uefi shell application parameters, see the User Guide.

2.3 Emulation environment without secondary storage

On an emulation platform where secondary storage is not available, perform the following steps:

Add the path to 'Bsa.efi' file in the UEFI FD file.
Build UEFI image including the UEFI Shell.
Boot the system to UEFI shell.
Run the executable 'Bsa.efi' to start the compliance tests. For details about the parameters,see the User Guide.
Copy the UART console output to a log file for analysis and certification.

Linux OS-based tests

Certain Peripheral, PCIe and Memory map tests require Linux operating system with kernel version 5.13 or above. This chapter provides information on executing tests from the Linux application.

1. Build steps and environment setup

This section lists the porting and build steps for the kernel module. The patch for the kernel tree and the Linux PAL are hosted separately on linux-acs repo

1.1 Building the kernel module

Prerequisites

Linux kernel source version 5.13.
Linaro GCC tool chain 7.5 or above.
Build environment for AArch64 Linux kernel.

Porting steps for Linux kernel

git clone https://git.gitlab.arm.com/linux-arm/linux-acs.git bsa-acs-drv
git clone https://github.com/ARM-software/bsa-acs.git bsa-acs
git clone https://github.com/torvalds/linux.git -b v5.11
export CROSS_COMPILE=<GCC7.5 toolchain path> pointing to /bin/aarch64-linux-gnu-
git apply <local_dir>/bsa-acs-drv/kernel/src/0001-BSA-ACS-Linux-5.13.patch to your kernel source tree.
make ARCH=arm64 defconfig && make -j $(nproc) ARCH=arm64

1.2 Build steps for BSA kernel module

cd <local_dir>/bsa-acs-drv/files
export CROSS_COMPILE=/bin/aarch64-linux-gnu-
export KERNEL_SRC=
./setup.sh <local_dir/bsa-acs>
./linux_bsa_acs.sh

Successful completion of above steps will generate bsa_acs.ko

1.3 BSA Linux application build

cd /linux_app/bsa-acs-app
export CROSS_COMPILE=/bin/aarch64-linux-gnu-
make

Successful completion of above steps will generate executable file bsa

2. Loading the kernel module

Before the BSA ACS Linux application can be run, load the BSA ACS kernel module using the insmod command.

shell> insmod bsa_acs.ko

3. Running BSA ACS

shell> ./bsa

For information on the BSA Linux application parameters, see the User Guide.

Security implication

The Arm SystemReady ACS test suite may run at a higher privilege level. An attacker may utilize these tests to elevate the privilege which can potentially reveal the platform security assets. To prevent the leakage of Secure information, Arm strongly recommends that you run the ACS test suite only on development platforms. If it is run on production systems, the system should be scrubbed after running the test suite.

Limitations

PCIE iEP rules are out of scope for current release.
ITS rules are available only for systems that present firmware compliant to SBBR.
Some PCIe and Exerciser test are dependent on PCIe features supported by the test system. Please fill the required API's with test system information.
- pal_pcie_p2p_support : If the test system PCIe supports peer to peer transaction.
- pal_pcie_is_cache_present : If the test system supports PCIe address translation cache.
- pal_pcie_get_legacy_ir_map : Fill system legacy ir map Below exerciser capabilities are required by exerciser test.
- MSI-X interrupt generation.
- Incoming Transaction Monitoring(order, type).
- Initiating transacions from and to the exerciser.
- Ability to check on BDF and register address seen for each configuration address along with access type.

License

BSA ACS is distributed under Apache v2.0 License.

Feedback, contributions, and support

For feedback, use the GitHub Issue Tracker that is associated with this repository.
For support, send an email to "[email protected]" with details.
Arm licensees may contact Arm directly through their partner managers.
Arm welcomes code contributions through GitHub pull requests. See the GitHub documentation on how to raise pull requests.

Name		Name	Last commit message	Last commit date
Latest commit History 16 Commits
docs		docs
linux_app		linux_app
platform		platform
prebuilt_images		prebuilt_images
test_pool		test_pool
tools/scripts		tools/scripts
uefi_app		uefi_app
val		val
LICENSE.md		LICENSE.md
README.md		README.md
changelog.txt		changelog.txt

License

sunnywang-arm/bsa-acs

Folders and files

Latest commit

History

Repository files navigation

Base System Architecture - Architecture Compliance Suite