Skip to content

ESP32APRS_LoRa V0.4

Latest
Compare
Choose a tag to compare
@nakhonthai nakhonthai released this 04 Dec 17:24
· 5 commits to main since this release

 ## V0.4 History Update (Factory Reset Require)
-Add (G)FSK Modem for D.I.Y
-Add GFSK9600(G3RUH) Modem for APRS(Test by Direwolf,VX8-DR,FTM-350,FTM-400DR TX Delay 100mS)
-Add AIS (Automatic Identification System) RX Only, IGate by APRS-CB recommend.
-Add Enable/Disable AX.25 Protocol
-Add Dashboard for ship on last heard
-Add Board TTGO T-Beam V1.2, TTGO LoRa32 (T3) V1.6, Heltec V3 Support.
-Fix Encode/Decode HDLC,NRZI
-Fix RF Output power
-Fix Web Service
-Fix Allocate memory
-Fix OLED SSD1306,SH1106

V0.4a History Update

-Fix register lora chip sx126x
-Fix RX init timeout

V0.4b History Update

-Rebuild Platfrom Espressif 32 V6.9.0

How to Update new firmware

  • 1.Download firmware and open the web browser in to webservice
  • 2.Select Tab About/Firmware and click Choose File for firmware and click Firmware Update , wait and reboot system
  • 3 Factory re connect the USB plug, when display logo on OLED or LED RX,TX light then press hold the BOOT button
  • 4.You can enter configuration mode in 2 ways:
  • 4.1 Default config then go to WiFi AP SSID: ESP32APRS_LoRa PASS: aprsthnetwork and open a web browser to the website. http://192.168.4.1 default web auth USER: admin PASS: admin
  • 4.2 Default config then go to share or set router WiFi SSID: APRSTH PASS: aprsthnetwork and use web browser by IP from router/share smartphone default web auth USER: admin PASS: admin
  • 5.You can new modify GPIO on webservice in the tab MOD

ESP32IGate firmware installation (do it first time, next time via the web browser)

  • 1.Connect the USB cable to the HT_CT62,TTGO LoRa 32,ESP32-Doit-devkit,DIY other
  • 2.Press and hold the BOOT button (without releasing it), then press the RST button, then release the RST button, and finally release the BOOT button
  • 3.Download firmware and open the program ESP32 DOWNLOAD TOOL, set it in the firmware upload program, set the firmware to ESP32IGate_Vxx_DIY_OLED.bin for non RF Module or ESP32_Vxx.bin,ESP32S3_Vxx.bin,ESP32C3_Vxx.bin,ESP32C6_Vxx.bin with RF Module location 0x10000 and partitions.bin at 0x8000 and bootloader.bin at 0x1000 (ESP32-C3 at 0x0000) and boot_app0.bin at 0xe000
  • 4.Click the START button in the program and wait for the upload to complete
  • 5 Factory re connect the USB plug, when display logo on OLED or LED RX,TX light then press hold the BOOT button
  • 6.You can enter configuration mode in 2 ways:
  • 6.1 Default config then go to WiFi AP SSID: ESP32APRS_LoRa PASS: aprsthnetwork and open a web browser to the website. http://192.168.4.1 default web auth USER: admin PASS: admin
  • 6.2 Default config then go to share or set router WiFi SSID: APRSTH PASS: aprsthnetwork and use web browser by IP from router/share smartphone default web auth USER: admin PASS: admin
  • 7.You can new modify GPIO on webservice in the tab MOD

ESP32 Flash Download Tools

https://www.espressif.com/en/support/download/other-tools

Firmware for board

ESP32_Vxx.zip for TTGO-LoRa32-V1, TTGO T-Beam-V1.2, TTGO LoRa32 (T3) V1.6, HELTEC_WiFi_LoRa32_V2 or D.I.Y from ESP32-DevKit
ESP32C3_Vxx.zip for Heltec HT-CT62 for D.I.Y from ESP32-C3 DevKit
ESP32S3_Vxx.zip for Heltec HTIT-Tracker and Heltec_WiFi_LoRa32_V3 and TTGO T-Beam Supreme or D.I.Y from ESP32-S3 DevKit
ESP32S3_Dongle_Vxx.zip for APRS LoRa Dongle and APRS LoRa HT Version.