-
Notifications
You must be signed in to change notification settings - Fork 223
900 Features and Options
VK2EFL edited this page Jul 20, 2019
·
11 revisions
There are several features that can be enabled and options chosen that can be used to enhance your K3NG keyer. Below are the possible features and options that can be selected. To enable either a feature or an option, they must be uncommented. This is done by removing the // at the beginning of the line.
Generally FEATURES add more bytes to the compiled binary (the code size becomes larger), OPTIONS change code behaviour
This document is in process. Feel free to help by copying appropriate contents at the blog into a new page and link the appropriate feature to it.
| Features | Notes |
|---|---|
| FEATURE_COMMAND_BUTTONS | Enable command buttons |
| FEATURE_COMMAND_LINE_INTERFACE | Enable command line interface over serial connection |
| FEATURE_MEMORIES | on the Arduino Due, you must have FEATURE_EEPROM_E24C1024 and E24C1024 EEPROM hardware in order to compile this |
| FEATURE_MEMORY_MACROS | provides for the use of macros that can be used and stored in memory |
| FEATURE_WINKEY_EMULATION | disabling Automatic Software Reset is highly recommended (see documentation) |
| FEATURE_BEACON | enables the use of the keyer as a beacon code generator. Beacon message in memory 1 |
| FEATURE_CALLSIGN_RECEIVE_PRACTICE | |
| FEATURE_POTENTIOMETER | Speed control, if enabled, must have pot connected or false wpm will trigger changes randomly |
| FEATURE_SERIAL_HELP | show help for command line interface |
| FEATURE_HELL | |
| FEATURE_PS2_KEYBOARD | Use a PS2 keyboard to send code - Change keyboard layout (non-US) in K3NG_PS2Keyboard.h. Additional options below. |
| FEATURE_USB_KEYBOARD | Use a USB keyboard to send code - Uncomment three lines in k3ng_keyer.ino (search for note_usb_uncomment_lines) |
| FEATURE_CW_COMPUTER_KEYBOARD | Have an Arduino Due or Leonardo act as a USB HID (Human Interface Device) keyboard and use the paddle to "type" characters on the computer |
| FEATURE_DEAD_OP_WATCHDOG | if more than 100 consecutive elemts are sent then it is assumed the operator has gone to sleep at the key |
| FEATURE_AUTOSPACE | enables the autospace feature |
| FEATURE_FARNSWORTH | enables the Farnsworth timing feature |
| FEATURE_DL2SBA_BANKSWITCH | Switch memory banks feature as described here: http://dl2sba.com/index.php?option=com_content&view=article&id=131:nanokeyer&catid=15:shack&Itemid=27#english |
| FEATURE_LCD_4BIT | classic LCD disidefplay using 4 I/O lines |
| FEATURE_LCD_ADAFRUIT_I2C | Adafruit I2C LCD display using MCP23017 at addr 0x20 |
| FEATURE_LCD_ADAFRUIT_BACKPACK | Adafruit I2C LCD Backup using MCP23008 |
| FEATURE_LCD_YDv1 | YourDuino I2C LCD display with old LCM 1602 V1 ic |
| FEATURE_LCD1602_N07DH | http://linksprite.com/wiki/index.php5?title=16_X_2_LCD_Keypad_Shield_for_Arduino |
| FEATURE_CW_DECODER | Decode CW into the keyer |
| FEATURE_SLEEP | go to sleep after x minutes to conserve battery power (not compatible with Arduino DUE, may have mixed results with Mega and Mega ADK) |
| FEATURE_ROTARY_ENCODER | Use a rotary encoder for speed control |
| FEATURE_CMOS_SUPER_KEYER_IAMBIC_B_TIMING | |
| FEATURE_USB_MOUSE | Uncomment three lines in k3ng_keyer.ino (search for note_usb_uncomment_lines) |
| FEATURE_CAPACITIVE_PADDLE_PINS | remove the bypass capacitors on the paddle_left and paddle_right lines when using capactive paddles |
| FEATURE_LED_RING | Mayhew Labs Led Ring support for rotary encoder |
| FEATURE_ALPHABET_SEND_PRACTICE | enables command mode S command - created by Ryan, KC2ZWM |
| FEATURE_PTT_INTERLOCK | |
| FEATURE_QLF | enables QLF sending (sending with the left foot) |
| FEATURE_EEPROM_E24C1024 | for use on an Arduino Due (which has no EEPROM), you must have E24C1024 EEPROM hardware in order to compile this |
| FEATURE_STRAIGHT_KEY | |
| FEATURE_DYNAMIC_DAH_TO_DIT_RATIO | |
| FEATURE_PADDLE_ECHO | |
| FEATURE_STRAIGHT_KEY_ECHO | |
| FEATURE_AMERICAN_MORSE | |
| FEATURE_4x4_KEYPAD | using an external 4x4 keypad to play memories, keypad keys are custom programmable |
| FEATURE_3x4_KEYPAD | using an external 3x4 keypad to play memories, keypad keys are custom programmable |
| FEATURE_SEQUENCER | enables the sequencer feature |
| FEATURE_COMMAND_LINE_INTERFACE_ON_SECONDARY_PORT | Activate the Command Line interface on the secondary serial port |
| Options | Notes |
|---|---|
| OPTION_SUPPRESS_SERIAL_BOOT_MSG | suppresses the boot message when connected by a serial port |
| OPTION_INCLUDE_PTT_TAIL_FOR_MANUAL_SENDING | include PTT tail timing for manual sending |
| OPTION_EXCLUDE_PTT_HANG_TIME_FOR_MANUAL_SENDING | include PTT hang time for manual sending |
| OPTION_WINKEY_DISCARD_BYTES_AT_STARTUP | if ASR is not disabled, you may need this to discard errant serial port bytes at startup |
| OPTION_WINKEY_STRICT_EEPROM_WRITES_MAY_WEAR_OUT_EEPROM | |
| OPTION_WINKEY_SEND_WORDSPACE_AT_END_OF_BUFFER | |
| OPTION_WINKEY_STRICT_HOST_OPEN | require an admin host open Winkey command before doing any other commands |
| OPTION_WINKEY_2_SUPPORT | comment out to revert to Winkey version 1 emulation |
| OPTION_WINKEY_INTERRUPTS_MEMORY_REPEAT | |
| OPTION_WINKEY_2_HOST_CLOSE_NO_SERIAL_PORT_RESET | activate this when using Winkey 2 emulation and Win-Test |
| OPTION_WINKEY_FREQUENT_STATUS_REPORT | activate this to make Winkey emulation play better with RUMlog and RUMped |
| OPTION_WINKEY_IGNORE_LOWERCASE | Enable for typical K1EL Winkeyer behavior (use for SkookumLogger version 1.10.14 and prior to workaround "r" bug) |
| OPTION_WINKEY_BLINK_PTT_ON_HOST_OPEN | |
| OPTION_REVERSE_BUTTON_ORDER | This is mainly for the DJ0MY NanoKeyer http://nanokeyer.wordpress.com/ |
| OPTION_PROG_MEM_TRIM_TRAILING_SPACES | trim trailing spaces from memory when programming in command mode |
| OPTION_DIT_PADDLE_NO_SEND_ON_MEM_RPT | this makes dit paddle memory interruption a little smoother |
| OPTION_MORE_DISPLAY_MSGS | additional optional display messages - comment out to save a small amount of memory |
| OPTION_WATCHDOG_TIMER | this enables a four second ATmega48/88/168/328 watchdog timer; use for unattended/remote operation only |
| OPTION_MOUSE_MOVEMENT_PADDLE | experimental (just fooling around) - mouse movement will act like a paddle |
| OPTION_NON_ENGLISH_EXTENSIONS | add support for additional CW characters (i.e. À, Å, Þ, etc.) |
| OPTION_KEEP_PTT_KEYED_WHEN_CHARS_BUFFERED | this option keeps PTT high if there are characters buffered from the keyboard, the serial interface, or Winkey |
| OPTION_DISPLAY_NON_ENGLISH_EXTENSIONS | LCD display suport for non-English (NO/DK/DE) characters - Courtesy of OZ1JHM |
| OPTION_UNKNOWN_CHARACTER_ERROR_TONE | Play a tone when an unknown character is entered, aka you messed up so bad the keyer hasn't a clue :-) |
| OPTION_DO_NOT_SAY_HI | does not display 'hi' on the LCD or sound 'hi' with sidetone, when starting |
| OPTION_USE_ORIGINAL_VERSION_2_1_PS2KEYBOARD_LIB | |
| OPTION_PS2_NON_ENGLISH_CHAR_LCD_DISPLAY_SUPPORT | makes some non-English characters from the PS2 keyboard display correctly in the LCD display (donated by Marcin sp5iou) |
| OPTION_PS2_KEYBOARD_RESET | reset the PS2 keyboard upon startup with 0xFF (contributed by Bill, W9BEL) |
| OPTION_SAVE_MEMORY_NANOKEYER | numerous non-inclusions of code segments in order to save memory so that the compiled code will fit into the available space on a nanoKeyer |
| OPTION_CW_KEYBOARD_CAPSLOCK_BEEP | |
| OPTION_CW_KEYBOARD_ITALIAN | |
| OPTION_CW_DECODER_GOERTZEL_AUDIO_DETECTOR | |
| OPTION_INVERT_PADDLE_PIN_LOGIC | paddles are active high rather than the default of active low |
| OPTION_ADVANCED_SPEED_DISPLAY | enables "nerd" speed visualization on display: wpm, cpm (char per min), duration of dit and dah in milliseconds and ratio (contributed by Giorgio, IZ2XBZ) |
| OPTION_PROSIGN_SUPPORT | additional prosign support for paddle and straight key echo on display, CLI, and in memory storage |
| OPTION_RUSSIAN_LANGUAGE_SEND_CLI | Russian language CLI sending support (contributed by Павел Бирюков, UA1AQC) |