mediatek: Routerich AX3000: add OpenWrt U-Boot layout

This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The aims: 1. Get open-source U-Boot; 2. Get maximum available free space in OpenWrt. Install ------- 1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the /tmp folder of the router using scp. 2. Make mtd partitions backups: http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock contents 3. Install kmod-mtd-rw: ``` opkg update && opkg install kmod-mtd-rw ``` 4. Write FIP and preloader: ``` insmod mtd-rw i_want_a_brick=1 mtd unlock BL2 mtd erase BL2 mtd write /tmp/ubootmod-preloader.bin BL2 mtd unlock FIP mtd erase FIP mtd write /tmp/ubootmod-bl31-uboot.fip FIP ``` 5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root with IP 192.168.1.254. 6. Reboot router: ``` reboot ``` U-Boot will automatically download from the tftp server and boot OpenWrt initramfs system. 7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the router using scp. 8. Run sysupgrade: ``` sysupgrade -n /tmp/squashfs-sysupgrade.itb ``` Recovery -------- 1. Place OpenWrt initramfs-recovery.itb image (with original name) on the tftp server (IP: 192.168.1.254). 2. Press "reset" button and power on the router. After ~10 sec release the button. 3. Use OpenWrt initramfs system for recovery. BL2 and FIP recovery -------------------- Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed: Link: https://github.com/981213/mtk_uartboot Return to stock: ---------------- 1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the router using scp. 2. Install kmod-mtd-rw: ``` opkg update && opkg install kmod-mtd-rw ``` 3. Restore stock U-Boot and reboot: ``` insmod mtd-rw i_want_a_brick=1 mtd unlock BL2 mtd erase BL2 mtd write /tmp/BL2.bin BL2 mtd unlock FIP mtd erase FIP mtd write /tmp/FIP.bin FIP reboot ``` 4. Open U-Boot web recovery, upload stock firmware image and start upgrade. Link: http://192.168.1.1 Signed-off-by: Mikhail Zhilkin <[email protected]> (cherry picked from commit 0cc0471)
csharper2005 · Nov 18, 2024 · dc3ca8c · dc3ca8c
1 parent 878dc6f
commit dc3ca8c
Show file tree

Hide file tree

Showing 9 changed files with 411 additions and 321 deletions.
diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic
@@ -73,6 +73,7 @@ h3c,magic-nx30-pro|\
 jcg,q30-pro|\
 netcore,n60|\
 qihoo,360t7|\
+routerich,ax3000-ubootmod|\
 tplink,tl-xdr4288|\
 tplink,tl-xdr6086|\
 tplink,tl-xdr6088|\

diff --git a/target/linux/mediatek/dts/mt7981b-routerich-ax3000-common.dtsi b/target/linux/mediatek/dts/mt7981b-routerich-ax3000-common.dtsi
@@ -0,0 +1,302 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "mt7981.dtsi"
+
+/ {
+	aliases {
+		label-mac-device = &wan;
+
+		led-boot = &led_power_blue;
+		led-failsafe = &led_power_blue;
+		led-running = &led_power_blue;
+		led-upgrade = &led_power_blue;
+
+		serial0 = &uart0;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			label = "mesh";
+			linux,input-type = <EV_SW>;
+			linux,code = <BTN_0>;
+			gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		button-1 {
+			label = "reset";
+			gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WLAN;
+			function-enumerator = <50>;
+			gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WAN;
+			gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_power_blue: led-2 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <1>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <2>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <3>;
+			gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led-6 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_WAN;
+			gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-7 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_WLAN;
+			function-enumerator = <24>;
+			gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		led-8 {
+			color = <LED_COLOR_ID_BLUE>;
+			/* LED_FUNCTION_MESH isn't implemented yet */
+			function = "mesh";
+			gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	memory {
+		reg = <0 0x40000000 0 0x10000000>;
+	};
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		nvmem-cell-names = "mac-address";
+		nvmem-cells = <&macaddr_factory_4 (-1)>;
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+};
+
+&mdio_bus {
+	switch: switch@1f {
+		compatible = "mediatek,mt7531";
+		reg = <0x1f>;
+		reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_flash_pins>;
+	status = "okay";
+
+	/* ESMT F50L1G41LB (128M) */
+	spi: spi_nand@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-nand";
+		reg = <0>;
+
+		spi-max-frequency = <52000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+
+		spi-cal-enable;
+		spi-cal-mode = "read-data";
+		spi-cal-datalen = <7>;
+		spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
+		spi-cal-addrlen = <5>;
+		spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+		partitions: partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0_all {
+				label = "spi0.0";
+				reg = <0x0 0x8000000>;
+				read-only;
+			};
+
+			partition@0 {
+				label = "BL2";
+				reg = <0x0 0x100000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "Factory";
+				reg = <0x180000 0x200000>;
+				read-only;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					eeprom_factory_0: eeprom@0 {
+						reg = <0x0 0x1000>;
+					};
+
+					macaddr_factory_4: macaddr@4 {
+						compatible = "mac-base";
+						reg = <0x4 0x6>;
+						#nvmem-cell-cells = <1>;
+					};
+				};
+			};
+
+			partition@380000 {
+				label = "FIP";
+				reg = <0x380000 0x200000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan3";
+		};
+
+		wan: port@4 {
+			reg = <4>;
+			label = "wan";
+
+			nvmem-cell-names = "mac-address";
+			nvmem-cells = <&macaddr_factory_4 (-2)>;
+		};
+
+		port@6 {
+			reg = <6>;
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&pio {
+	spi0_flash_pins: spi0-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+		};
+
+		conf-pd {
+			pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	nvmem-cell-names = "eeprom";
+	nvmem-cells = <&eeprom_factory_0>;
+};
+
+&xhci {
+	status = "okay";
+	mediatek,u3p-dis-msk = <0x1>;
+};
diff --git a/target/linux/mediatek/dts/mt7981b-routerich-ax3000-ubootmod.dts b/target/linux/mediatek/dts/mt7981b-routerich-ax3000-ubootmod.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+#include "mt7981b-routerich-ax3000-common.dtsi"
+
+/ {
+	model = "Routerich AX3000 (OpenWrt U-Boot layout)";
+	compatible = "routerich,ax3000-ubootmod", "mediatek,mt7981";
+};
+
+&chosen {
+	rootdisk = <&ubi_fit_volume>;
+};
+
+&partitions {
+	partition@100000 {
+		label = "u-boot-env-orig";
+		reg = <0x100000 0x80000>;
+		read-only;
+	};
+
+	partition@580000 {
+		label = "ubi";
+		reg = <0x580000 0x7a80000>;
+		compatible = "linux,ubi";
+
+		volumes {
+			ubi_fit_volume: ubi-volume-fit {
+				volname = "fit";
+			};
+
+			ubi_ubootenv: ubi-volume-ubootenv {
+				volname = "ubootenv";
+			};
+
+			ubi_ubootenv2: ubi-volume-ubootenv2 {
+				volname = "ubootenv2";
+			};
+		};
+	};
+};
+
+&ubi_ubootenv {
+	nvmem-layout {
+		compatible = "u-boot,env-redundant-bool";
+	};
+};
+
+&ubi_ubootenv2 {
+	nvmem-layout {
+		compatible = "u-boot,env-redundant-bool";
+	};
+};