Releases: Thinkersbluff/DGUS-Reloaded_for_CR6-Klipper_Component
Release 1.3.5 - Stable
CAUTION: The Source.zip and Source.tar.gz files on this release are for release v1.3.4, not v1.3.5. Use ONLY the other two .zip files from this Assets list. (Sorry, somehow failed to notice when the Pull Request did not complete at v1.3.5.) :(
This baseline is designed to support version 0.4.4 of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
This release incorporates the scripts and code required to support the new Information page of the DWIN_SET component at v0.4.4.
It also modifies the behaviour of the printing function to restore %Feed Rate and %Flow Rate to 100% as part of the DGUS_END_PRINT routine, to prevent accidentally leaving the extruder feedrate "ridiculously high" when unloading a filament.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
If this is your first Klipper installation, I recommend that you create a clean installation - as described in the draft guide.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release 1.3.4 - Stable
This baseline is designed to support version 0.4.3 of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
This release incorporates the scripts and code required to support the "delete file" capability of ;the DWIN_SET component at v0.4.3.
IF you have already installed version 1.3.3 of this firmware, then you need only replace the t5uid1 folder (and all of its contents) in klippy/extras, to install this version. i.e.; The Related Changes folder contents have not changed.
IF, however, this is the first version of DGUS-Reloaded for CR6 that you are installing, you will need to follow all of the installation instructions.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
If this is your first Klipper installation, I recommend that you create a clean installation - as described in the draft guide.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release 1.3.3
This baseline is designed to support version 0.4.2 of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
This release incorporates the scripts and code required to support the scrollable fileslist and print capabilties of ;the DWIN_SET component at v0.4.2.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
If this is your first Klipper installation, I recommend that you create a clean installation - as described in the draft guide.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release 1.3.2
This baseline will support beta-testing version 0.4.1 - Beta of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
This release fixes two dgus-reloaded interface issues introduced approximately June 2024, by changes to probe.py and bed_mesh.py in Klipper/klippy/extras.
IF YOU HAVE ALREADY INSTALLED v1.3.0 or 1.3.1, YOU NEED ONLY REPLACE t5uid1.py AND vars-in.cfg WITH THE VERSIONS IN THIS RELEASE.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
I recommend that you create a clean installation - as described in the draft guide - if this is your first Klipper installation.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release 1.3.1
This baseline will support beta-testing version 0.4.1 - Beta of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
NOTE: THE ONLY DIFFERENCE BETWEEN THIS RELEASE AND 1.3.0 IS THAT I SHORTENED SOME PATHNAMES TO MAKE IT EASIER FOR YOU TO DOWNLOAD AND UNPACK THE SOURCE.ZIP FILE.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
I recommend that you create a clean installation - as described in the draft guide - if this is your first Klipper installation.
CAUTION: During the development of this app, I made the "mistake" of upgrading from Python 3.9.2 to 3.11.1. My system did not then work correctly, until I made a clean installation, which includes Python 3.9.2.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release 1.3.0 (no version 1.2.9 was released)
This baseline will support beta-testing version 0.4.1 - Beta of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
I recommend that you create a clean installation - as described in the draft guide - if this is your first Klipper installation.
CAUTION: During the development of this app, I made the "mistake" of upgrading from Python 3.9.2 to 3.11.1. My system did not then work correctly, until I made a clean installation, which includes Python 3.9.2.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release v1.2.8
This baseline will support beta-testing version 0.4.0 - Beta of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
I recommend that you create a clean installation - as described in the draft guide - if this is your first Klipper installation.
CAUTION: During the development of this app, I made the "mistake" of upgrading from Python 3.9.2 to 3.11.1. My system did not then work correctly, until I made a clean installation, which includes Python 3.9.2.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release 1.2.7
This baseline will support beta-testing version 0.3.9 - Beta of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
I recommend that you create a clean installation - as described in the draft guide - if this is your first Klipper installation.
CAUTION: During the development of this app, I made the "mistake" of upgrading from Python 3.9.2 to 3.11.1. My system did not then work correctly, until I made a clean installation, which includes Python 3.9.2.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release 1.2.6
This baseline will support beta-testing version 0.3.8 - Beta of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
BTT SKR CR6
Creality 4.5.2
Creality 4.5.3
Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
I recommend that you create a clean installation - as described in the draft guide - if this is your first Klipper installation.
CAUTION: During the development of this app, I made the "mistake" of upgrading from Python 3.9.2 to 3.11.1. My system did not then work correctly, until I made a clean installation, which includes Python 3.9.2.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. (NOTE: You also need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!
Release 1.2.5
This baseline will support beta-testing version 0.3.7 - Beta of the DGUS-Reloaded DWIN_SET available at https://github.com/Thinkersbluff/DGUS-Reloaded_for_CR6-DWIN-SET_Component.
CAUTION: the configuration files are from the test machine, which is a Kickstarter version of the CR6-SE, but which is not in stock configuration. I recommend that you use WinMerge to compare your files with these ones, and decide which edits to incorporate when installing or updating DGUS-Reloaded into your MainSail/Klipper system, rather than simply overwriting your files with mine.
Annotated pre-configured files are provided for installing this firmware on each of the 4 types of CR6 motherboard:
- BTT SKR CR6
- Creality 4.5.2
- Creality 4.5.3
- Creality ERA 1.1.0.3
Please NOTE that whichever system you have, it is likely to differ from that of my test printer.
I have done my best to annotate the printer.cfg files to guide you to which values require tuning or changing for these files to work properly with your system.
I recommend that you create a clean installation - as described in the draft guide - if this is your first Klipper installation.
CAUTION: During the development of this app, I made the "mistake" of upgrading from Python 3.9.2 to 3.11.1. My system did not then work correctly, until I made a clean installation, which includes Python 3.9.2.
NOTE: It is possible to install the DGUS-Reloaded Klipper Component on top of the very latest Klipper, just by copying the folder t5uid1 - and all of its contents - into the klipper/klippy/extras folder on your pi host. If you choose to do that, expect that you will have to do that again, each time that Klipper is updated. I will research how to make this process even easier, in future releases. (NOTE: You would still need to flash the Klipper.bin file to the motherboard, and the DWIN_SET to your display, but you could go ahead and do a clean install of the pre-built Mainsail OS in the Raspberry Pi Imager, then sFTP the attached t5uid1 folder after the fact. I tried to describe how I did that, in the draft installation guide in the docs folder.
I describe a five-step process for installing DGUS-Reloaded over a Klipper3D/Klipper installation, in the site README file.
If you find a better way, please share it with me in the Discussions section!