test empty project

examples/knx-demo/knx-demo.ino

@@ -1,114 +1,20 @@
 #include <Arduino.h>
-#include <knx.h>
 
-#if MASK_VERSION != 0x07B0 && (defined ARDUINO_ARCH_ESP8266 || defined ARDUINO_ARCH_ESP32)
-#include <WiFiManager.h>
-#endif
 
-// create named references for easy access to group objects
-#define goCurrent knx.getGroupObject(1)
-#define goMax knx.getGroupObject(2)
-#define goMin knx.getGroupObject(3)
-#define goReset knx.getGroupObject(4)
 
-float currentValue = 0;
-float maxValue = 0;
-float minValue = RAND_MAX;
-long lastsend = 0;
 
-void measureTemp()
-{
-    long now = millis();
-    if ((now - lastsend) < 2000)
-        return;
-
-    lastsend = now;
-    int r = rand();
-    currentValue = (r * 1.0) / (RAND_MAX * 1.0);
-    currentValue *= 100 * 100;
-
-    // write new value to groupobject
-    goCurrent.value(currentValue);
-
-    if (currentValue > maxValue)
-    {
-        maxValue = currentValue;
-        goMax.value(maxValue);
-    }
-
-    if (currentValue < minValue)
-    {
-        minValue = currentValue;
-        goMin.value(minValue);
-    }
-}
-
-// callback from reset-GO
-void resetCallback(GroupObject& go)
-{
-    if (go.value())
-    {
-        maxValue = 0;
-        minValue = 10000;
-    }
-}
 
 void setup()
 {
     Serial.begin(115200);
-    ArduinoPlatform::SerialDebug = &Serial;
 
     randomSeed(millis());
 
-#if MASK_VERSION != 0x07B0 && (defined ARDUINO_ARCH_ESP8266 || defined ARDUINO_ARCH_ESP32)
-    WiFiManager wifiManager;
-    wifiManager.autoConnect("knx-demo");
-#endif
-
-    // read adress table, association table, groupobject table and parameters from eeprom
-    knx.readMemory();
-
-    // print values of parameters if device is already configured
-    if (knx.configured())
-    {
-        // register callback for reset GO
-        goReset.callback(resetCallback);
-        goReset.dataPointType(DPT_Trigger);
-        goCurrent.dataPointType(DPT_Value_Temp);
-        goMin.dataPointType(DPT_Value_Temp);
-        goMax.dataPointType(DPT_Value_Temp);
-
-        Serial.print("Timeout: ");
-        Serial.println(knx.paramByte(0));
-        Serial.print("Zykl. senden: ");
-        Serial.println(knx.paramByte(1));
-        Serial.print("Min/Max senden: ");
-        Serial.println(knx.paramByte(2));
-        Serial.print("Aenderung senden: ");
-        Serial.println(knx.paramByte(3));
-        Serial.print("Abgleich: ");
-        Serial.println(knx.paramByte(4));
-    }
-
-    // pin or GPIO the programming led is connected to. Default is LED_BUILTIN
-    // knx.ledPin(LED_BUILTIN);
-    // is the led active on HIGH or low? Default is LOW
-    // knx.ledPinActiveOn(HIGH);
-    // pin or GPIO programming button is connected to. Default is 0
-    // knx.buttonPin(0);
 
-    // start the framework.
-    knx.start();
 }
 
 void loop()
 {
-    // don't delay here to much. Otherwise you might lose packages or mess up the timing with ETS
-    knx.loop();
 
-    // only run the application code if the device was configured with ETS
-    if (!knx.configured())
-        return;
 
-    measureTemp();
 }

examples/knx-demo/platformio-ci.ini

@@ -92,8 +92,8 @@ board_build.core = earlephilhower
 ; while working with VS Code.
 lib_extra_dirs = ../../../
 
-lib_deps =
-  knx
+;lib_deps =
+;  knx
 
 lib_ldf_mode = chain
 

examples/knx-demo/platformio.ini

@@ -162,7 +162,7 @@ lib_extra_dirs = ../../../
 lib_deps =
   knx
 
-lib_ldf_mode = chain
+lib_ldf_mode = deep+
 
 build_flags =
   -DMASK_VERSION=0x07B0