config: Add LDO Leviathan v1.2 generic config

Signed-off-by: Stefan Dej <[email protected]>

config/generic-ldo-leviathan-v1.2.cfg

@@ -0,0 +1,241 @@
+# This file contains common pin mappings for the LDO Leviathan v1.2.
+
+# To use this config, during "make menuconfig", select "Enable
+# low-level configuration options", select the STM32F446 micro-controller,
+# select a "32KiB bootloader", and select a "12Mhz crystal".
+
+# See docs/Config_Reference.md for a description of parameters.
+
+# HV-STEPPER-0
+[stepper_x]
+step_pin: PB10
+dir_pin: PB11
+enable_pin: !PG0
+microsteps: 32
+rotation_distance: 40
+endstop_pin: PC1 # X-ENDSTOP
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[tmc5160 stepper_x]
+spi_bus: spi4
+cs_pin: PE15
+#diag0_pin: PG1
+interpolate: False
+sense_resistor: 0.075
+run_current: 0.8
+stealthchop_threshold: 0
+
+# HV-STEPPER-1
+[stepper_y]
+step_pin: PF15
+dir_pin: PF14
+enable_pin: !PE9
+microsteps: 32
+rotation_distance: 40
+endstop_pin: PC2 # Y-ENDSTOP
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[tmc5160 stepper_y]
+spi_bus: spi4
+cs_pin: PE11
+#diag0_pin: PE10
+interpolate: False
+sense_resistor: 0.075
+run_current: 0.8
+stealthchop_threshold: 0
+
+# STEPPER-0
+[stepper_z]
+step_pin: PD4
+dir_pin: PD3
+enable_pin: !PD7
+microsteps: 32
+rotation_distance: 8
+endstop_pin: PC3 # Z-ENDSTOP
+position_endstop: 0
+position_max: 200
+
+[tmc2209 stepper_z]
+uart_pin: PD5
+#diag_pin: PD6
+interpolate: False
+run_current: 0.6
+stealthchop_threshold: 999999
+
+# The Leviathan was developed for Voron printers. It therefore has several
+# steppers for the z-axes, but only one heater for one extruder.
+
+# STEPPER-1
+#[stepper_z1]
+#step_pin: PC12
+#dir_pin: PC11
+#enable_pin: !PD2
+#microsteps: 32
+#rotation_distance: 8
+#
+#[tmc2209 stepper_z1]
+#uart_pin: PD5
+##diag_pin: PD6
+#interpolate: False
+#run_current: 0.6
+#stealthchop_threshold: 999999
+
+# STEPPER-2
+#[stepper_z2]
+#step_pin: PC9
+#dir_pin: PC8
+#enable_pin: !PC10
+#microsteps: 32
+#rotation_distance: 8
+#
+#[tmc2209 stepper_z2]
+#uart_pin: PA8
+##diag_pin: PA15
+#interpolate: False
+#run_current: 0.6
+#stealthchop_threshold: 999999
+
+# STEPPER-3
+#[stepper_z3]
+#step_pin: PG7
+#dir_pin: PG6
+#enable_pin: !PC7
+#microsteps: 32
+#rotation_distance: 8
+#
+#[tmc2209 stepper_z2]
+#uart_pin: PG8
+##diag_pin: PC6
+#interpolate: False
+#run_current: 0.6
+#stealthchop_threshold: 999999
+
+# STEPPER-4
+[extruder]
+step_pin: PD10
+dir_pin: PD9
+enable_pin: !PD13
+microsteps: 32
+rotation_distance: 22.67
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PG10 # HEATER
+sensor_pin:  PA2 # TH1
+sensor_type: ATC Semitec 104NT-4-R025H42G
+pullup_resistor: 2200
+control: pid
+pid_Kp: 36.787
+pid_Ki: 4.716
+pid_Kd: 71.735
+min_temp: 0
+max_temp: 250
+
+[tmc2209 stepper_z]
+uart_pin: PD11
+#diag_pin: PD12
+interpolate: False
+run_current: 0.5
+stealthchop_threshold: 0
+
+#[filament_switch_sensor material_0]
+#switch_pin: PC0 # FILAMENT-SENSOR
+
+[heater_bed]
+heater_pin: PG11 # HEATBED
+sensor_pin: PA1 # TH0
+sensor_type: ATC Semitec 104GT-2
+pullup_resistor: 2200
+control: pid
+pid_kp: 56.723
+pid_ki: 5.561
+pid_kd: 144.642
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PB7 # FAN0
+#tachometer_pin: PB0
+
+#[heater_fan fan1]
+#pin: PB3
+#tachometer_pin: PB4
+
+#[heater_fan fan2]
+#pin: PF7
+#tachometer_pin: PF6
+
+#[controller_fan fan3]
+#pin: PF9
+#tachometer_pin: PF8
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+# CAN bus is also available on this board
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=PG9, EXP1_2=PG12,
+    EXP1_3=PG13, EXP1_4=PG14,
+    EXP1_5=PC13, EXP1_6=PC14,
+    EXP1_7=PC15, EXP1_8=PF0,
+    EXP1_9=<GND>, EXP1_10=<5V>,
+
+    # EXP2 header
+    EXP2_1=PA6, EXP2_2=PA5,
+    EXP2_3=PE2, EXP2_4=PE4,
+    EXP2_5=PE3, EXP2_6=PA7,
+    EXP2_7=PE5, EXP2_8=<RST>,
+    EXP2_9=<GND>, EXP2_10=PE4,
+
+    # See the sample-lcd.cfg file for definitions of common LCD displays.
+
+    # EXTENSION PORT
+    EXP3_1=<5V>, EXP3_2=<5V>,       # max. 0.5A
+    EXP3_3=<GND>, EXP3_4=<GND>,
+    EXP3_5=<3.3V>, EXP3_6=<3.3V>,   # max. 0.5A
+    EXP3_7=PF5, EXP3_8=PF4,
+    EXP3_9=PF3, EXP3_10=PF2,
+    EXP3_11=PC4, EXP3_12=PC5,       # EXP3_11 and EXP3_12 are ADC inputs
+    EXP3_13=PB0, EXP3_14=PB1,       # EXP3_13 and EXP3_14 are ADC inputs
+    EXP3_15=PE8, EXP3_16=PE7,       # EXP3_15 is UART5_TX, EXP3_16 is UART5_RX
+    EXP3_17=PG5, EXP3_18=PG4,
+    EXP3_19=PG3, EXP3_20=PG2,
+    EXP3_21=PD15, EXP3_22=PD14,
+    EXP3_23=PB15, EXP3_24=PB14,     # EXP3_23 is SPI2_MOSI
+                                    # EXP3_24 is SPI2_MISO
+    EXP3_25=PB13, EXP3_26=PB12,     # EXP3_25 is SPI2_SCK + CAN2_TX
+                                    # EXP3_26 is SPI2_CS + CAN2_RX
+    EXP3_27=<GND>, EXP3_28=<GND>,
+    EXP3_29=<24V>, EXP3_30=<24V>,   # max. 0.5A
+
+#[probe]
+#sensor_pin: PF1 # Z-PROBE
+#z_offset: 0
+
+#[led my_led]
+#white_pin: PE6 # LED-Strip
+
+#[neopixel my_neopixel]
+#pin: PF10 # NEOPIXEL
+
+#[temperature_sensor th2]
+#sensor_type: ATC Semitec 104GT-2
+#sensor_pin: PA0 # TH2
+#pullup_resistor: 2200
+
+#[temperature_sensor TH3]
+#sensor_type: ATC Semitec 104GT-2
+#sensor_pin: PA3 # TH3
+#pullup_resistor: 2200

test/klippy/printers.test

@@ -238,6 +238,7 @@ CONFIG ../../config/generic-bigtreetech-octopus-pro-v1.0.cfg
 CONFIG ../../config/generic-fysetc-s6.cfg
 CONFIG ../../config/generic-fysetc-s6-v2.cfg
 CONFIG ../../config/generic-fysetc-spider.cfg
+CONFIG ../../config/generic-ldo-leviathan-v1.2.cfg
 CONFIG ../../config/generic-mks-rumba32-v1.0.cfg
 CONFIG ../../config/printer-ratrig-v-minion-2021.cfg