HyperSerialPico

Adalight serial port LED driver implementation for Raspberry Pi Pico RP2040.

Example of supported boards using Rp2040

Recommended boards with a built-in level shifter

To ensure the LEDs will work properly with the Pico board, a 3.3V to 5V level shifter is needed. You can use an external one e.g. SN74AHCT125N or just buy a model of rp2040 that already has it built-in: Adafruit Feather RP2040 Scorpio (output: GPIO16-23), Adafruit ItsyBitsy RP2040 (output: GPIO14), Pimoroni Plasma 2040 (GPIO14-15) or Pimoroni Plasma Stick 2040 W (GPIO15).

Supported LED strips

LED strip / Device	Single lane	Multi-segment
SK6812 cold white	yes	yes
SK6812 neutral white	yes	yes
WS281x	yes	yes
SPI (APA102, SK9812, HD107...)	yes	no*

* you don't need parallel mode for SPI LEDs, they are already using high speed 10Mb internal data line

How to flash it?

It's very easy and you don't need any special flasher.

1. First download the firmware directly from the Release folder.
   
   For HyperHDR and generic rp2040 choose HyperSerialPico_<type>.uf2 firmware where type is one of supported LEDs: sk6812 cold/neutral white, variants of ws2812 and apa102.
   
   Due to the often neglected issue of the required 5 volt logic necessary for the correct operation of the supported LEDs, we want to promote rp2040 boards with a built-in 3.3V to 5V level shifter and we provide firmware compiled to their GPIO specifications. You can find these firmware & short pin-out manuals in the archives: Adafruit_Feather_RP2040_Scorpio.zip, Adafruit_ItsyBitsy_2040.zip, Pimoroni_Plasma_2040.zip, Pimoroni_Plasma_Stick_2040_W.zip. Also you can read about their specific GPIO output in the Recommended boards with a built-in level shifter section above.
   
   If you are using an application other than HyperHDR, select the classic_adalight.zip archive, unzip it and select classic_adalight_HyperSerialPico_<type>.uf2 firmware (note: do not use firmware from this archive for HyperHDR, they do not support my AWA protocol extension, missing many options and are simply only backwards compatible with other applications).

2. Next put your Pico board into DFU mode:

• If your Pico board has only one button (boot) then press & hold it and connect the board to the USB port. Then you can release the button.
• If your Pico board has two buttons, connect it to the USB port. Then press & hold boot and reset buttons, then release reset and next release boot button.

3. In the system file explorer you should find new drive (e.g. called RPI-RP2 drive) exposed by the Pico board. Drag & drop (or copy) the selected firmware to this drive. The Pico will reset automaticly after the upload and after few seconds it will be ready to use by HyperHDR as a serial port device using Adalight driver.

HyperHDR configuration

You need HyperHDR v20 or newer. Make sure you have enabled AWA protocol and Esp8266/ESP32/Rp2040 handshake options. You can leave the speed at 2000000 because the CDC driver should use the highest possible speed automatically (at least it happens on Windows).

Default pinout

LED output (SK6812/WS281x): GPIO2 for Data
LED output (SPI LEDs): GPIO3 for Data, GPIO2 for Clock

If multi-segment mode is enabled for SK6812/WS281x, the output for the second segment is always the next GPIO pin (OUTPUT_DATA_PIN + 1).

rp2040 allows hardware SPI on corresponding pairs of pins:
spi0 ⇒ Data/Clock: GPIO3/GPIO2, GPIO19/GPIO18, GPIO7/GPIO6
spi1 ⇒ Data/Clock: GPIO11/GPIO10, GPI15/GPIO14, GPIO27/GPI26

Pinout can be changed, but you need to make changes to CMakeList.txt (e.g. OUTPUT_DATA_PIN / OUTPUT_SPI_DATA_PIN / OUTPUT_SPI_CLOCK_PIN) and recompile the project. Also multi-segment mode can be enabled in this file: SECOND_SEGMENT_INDEX option at the beginning and optionally SECOND_SEGMENT_REVERSED. Once compiled, the results can be found in the firmware folder.

Of course, you can also build your custom firmware completely online using Github Actions. The manual can be found on wiki. Be sure to follow the steps in the correct order.

Some benchmark results

Single RGBW LED strip	Max. refresh rate
300LEDs RGBW Refresh rate/continues output	83
600LEDs RGBW Refresh rate/continues output	42
900LEDs RGBW Refresh rate/continues output	28

Parallel multi-segment mode	Max. refresh rate
300LEDs RGBW Refresh rate/continues output SECOND_SEGMENT_INDEX=150	100
600LEDs RGBW Refresh rate/continues output SECOND_SEGMENT_INDEX=300	83
900LEDs RGBW Refresh rate/continues output SECOND_SEGMENT_INDEX=450	55