Skip to content

Latest commit

 

History

History
68 lines (51 loc) · 2.97 KB

ConnectingHardware.md

File metadata and controls

68 lines (51 loc) · 2.97 KB
Raw

GxEPD2

Arduino Display Library for SPI E-Paper Displays

  • With full Graphics and Text support using Adafruit_GFX

  • For SPI e-paper displays from Dalian Good Display

  • and SPI e-paper boards from Waveshare

important note :

  • the display panels are for 3.3V supply and 3.3V data lines
  • never connect data lines directly to 5V Arduino data pins, use e.g. 4k7/10k resistor divider
  • series resistor only is not enough for reliable operation (back-feed effect through protection diodes)
  • 4k7/10k resistor divider may not work with flat cable extensions or Waveshare 4.2 board, use level converter then
  • do not forget to connect GND
  • the actual Waveshare display boards now have level converters and series regulator, safe for 5V
  • use 3k3 pull-down on SS for ESP8266 for boards with level converters

mapping suggestions

mapping suggestion from Waveshare SPI e-Paper to Wemos D1 mini

  • BUSY -> D2, RST -> D4, DC -> D3, CS -> D8, CLK -> D5, DIN -> D7, GND -> GND, 3.3V -> 3.3V

mapping suggestion from Waveshare SPI e-Paper to ESP8266 NodeMCU:

  • BUSY -> D2, RST -> D4, DC -> D3, CS -> D8, CLK -> D5, DIN -> D7, GND -> GND, 3.3V -> 3.3V

mapping suggestion from Waveshare SPI e-Paper to generic ESP8266

  • BUSY -> GPIO4, RST -> GPIO2, DC -> GPIO0, CS -> GPIO15, CLK -> GPIO14, DIN -> GPIO13, GND -> GND, 3.3V -> 3.3V

mapping suggestion (by G6EJD) from Waveshare SPI e-Paper to ESP8266 Huzzah:

  • BUSY -> 03, RST -> 15, DC -> 02, CS -> 00, CLK -> 14, DIN -> 13, GND -> GND, 3.3V -> 3.3V

mapping suggestion for ESP32, e.g. LOLIN32, see .../variants/.../pins_arduino.h for your board

  • NOTE: there are variants with different pins for SPI ! CHECK SPI PINS OF YOUR BOARD
  • BUSY -> 4, RST -> 16, DC -> 17, CS -> SS(5), CLK -> SCK(18), DIN -> MOSI(23), GND -> GND, 3.3V -> 3.3V

mapping suggestion for STM32F1, e.g. STM32F103C8T6 "BluePill"

  • BUSY -> A1, RST -> A2, DC -> A3, CS-> A4, CLK -> A5, DIN -> A7

mapping suggestion for AVR, UNO, NANO etc.

  • BUSY -> 7, RST -> 9, DC -> 8, CS-> 10, CLK -> 13, DIN -> 11

mapping suggestion for Arduino MEGA

  • BUSY -> 7, RST -> 9, DC -> 8, CS-> 53, CLK -> 52, DIN -> 51

mapping suggestion for Arduino DUE

  • BUSY -> 7, RST -> 9, DC -> 8, CS-> 77, CLK -> 76, DIN -> 75
  • SPI pins are on 6 pin 2x3 SPI header

connection scheme for (discontinued) DESTM32-S2 connection board for e-paper panels:

   connection to the e-Paper display is through DESTM32-S2 connection board, available from Good Display

   DESTM32-S2 pinout (top, component side view, solder side of connector):

         |-------------------------------------------------
         |  VCC  |o o| VCC 5V  not needed
         |  GND  |o o| GND     GND
         |  3.3  |o o| 3.3     3.3V
         |  nc   |o o| nc
         |  nc   |o o| nc
         |  nc   |o o| nc
   MOSI  |  DIN  |o o| CLK     SCK
   SS    |  CS   |o o| DC      e.g. D3
   D4    |  RST  |o o| BUSY    e.g. D2
         |  nc   |o o| BS      GND
         |-------------------------------------------------