Skip to content

Latest commit

 

History

History
70 lines (51 loc) · 3.86 KB

README.md

File metadata and controls

70 lines (51 loc) · 3.86 KB
Raw

vmav-ros-pkg

ROS packages for vision-based MAVs.

Required dependencies:

  1. px-ros-pkg
  2. ethzasl_sensor_fusion (branch: catkin)
  3. asctec_mav_framework (branch: experimental)
  4. Boost >= 1.4.0 (Ubuntu package: libboost-all-dev)
  5. Eigen3 (Ubuntu package: libeigen3-dev)
  6. gflags (Ubuntu package: libgflags-dev)
  7. glog (Source install)
  8. OpenCV >= 2.4.8
  9. SuiteSparse >= 4.2.1 (Source install)
  10. RTI Connext DDS >= 5.1.0 (Source install to /opt)

If you use the packages for an academic publication, please cite either or both of the following papers depending on which packages you use:

Lionel Heng, Gim Hee Lee, and Marc Pollefeys,
Self-Calibration and Visual SLAM with a Multi-Camera System on a Micro Aerial Vehicle,
In Proc. Robotics: Science and Systems (RSS), 2014.

Lionel Heng, Dominik Honegger, Gim Hee Lee, Lorenz Meier,
Petri Tanskanen, Friedrich Fraundorfer, and Marc Pollefeys,
Autonomous Visual Mapping and Exploration With a Micro Aerial Vehicle,
Journal of Field Robotics (JFR), 31(4):654-675, 2014.

Hardware Synchronization Between Sensors

For hardware synchronization between the IMU on any AscTec platform and a single/multi-camera system, perform the following steps:

  1. Connect a cable between the GPIO pins on the autopilot (ground pin: GND, trigger signal pin: P1.16) and the correct pins on the camera hardware. The GPIO pins on the autopilot are shown in http://wiki.asctec.de/display/AR/I2C%2C+SPI%2C+GPIO.
  2. Compile the autopilot firmware from https://github.com/cvg/asctec_mav_framework/tree/experimental/asctec_hl_firmware. Note that this firmware differs from the official ethz-asl version, as the firmware is modified to support camera triggering.
  3. Flash the autopilot firmware by following the instructions in http://wiki.asctec.de/display/AR/SDK+Setup+for+Linux.
  4. Now you can adjust the camera trigger rate by modifying the value for the trigger_rate_cam parameter that is used by the asctec_hl_interface package.
  5. Each time the autopilot sends a trigger signal to the camera(s), the autopilot records the IMU data at that point of time. The asctec_hl_interface package publishes both a CamTrigger message and sensor_msgs::Imu message. Information in these messages can be used to infer which IMU message corresponds to a given camera image.

Acknowledgements

The primary author, Lionel Heng, is funded by the DSO Postgraduate Scholarship. This work is partially supported by the SNSF V-MAV grant (DACH framework).

The repository includes third-party code from the following sources:

1. M. Rufli, D. Scaramuzza, and R. Siegwart,
   Automatic Detection of Checkerboards on Blurred and Distorted Images,
   In Proc. IEEE/RSJ International Conference on Intelligent Robots and Systems, 2008.

2. Sameer Agarwal, Keir Mierle, and Others,
   Ceres Solver.
   https://code.google.com/p/ceres-solver/
    
3. D. Galvez-Lopez, and J. Tardos,
   Bags of Binary Words for Fast Place Recognition in Image Sequences,
   IEEE Transactions on Robotics, 28(5):1188-1197, October 2012.

4. L. Kneip, D. Scaramuzza, and R. Siegwart,
   A Novel Parametrization of the Perspective-Three-Point Problem for a
   Direct Computation of Absolute Camera Position and Orientation,
   In Proc. IEEE Conference on Computer Vision and Pattern Recognition, 2011.

5. pugixml
   http://pugixml.org/

6. E. Olson,
   AprilTag: A robust and flexible visual fiducial system,
   In Proc. IEEE International Conference on Robotics and Automation, 2011.