stm32f4xx_dac.c

/**
  ******************************************************************************
  * @file    stm32f4xx_dac.c
  * @author  MCD Application Team
  * @version V1.0.2
  * @date    05-March-2012
   * @brief   This file provides firmware functions to manage the following 
  *          functionalities of the Digital-to-Analog Converter (DAC) peripheral: 
  *           - DAC channels configuration: trigger, output buffer, data format
  *           - DMA management      
  *           - Interrupts and flags management
  *
  *  @verbatim
  *    
  *          ===================================================================
  *                             DAC Peripheral features
  *          ===================================================================
  *          
  *          DAC Channels
  *          =============  
  *          The device integrates two 12-bit Digital Analog Converters that can 
  *          be used independently or simultaneously (dual mode):
  *            1- DAC channel1 with DAC_OUT1 (PA4) as output
  *            1- DAC channel2 with DAC_OUT2 (PA5) as output
  *
  *          DAC Triggers
  *          =============
  *          Digital to Analog conversion can be non-triggered using DAC_Trigger_None
  *          and DAC_OUT1/DAC_OUT2 is available once writing to DHRx register 
  *          using DAC_SetChannel1Data() / DAC_SetChannel2Data() functions.
  *   
  *         Digital to Analog conversion can be triggered by:
  *             1- External event: EXTI Line 9 (any GPIOx_Pin9) using DAC_Trigger_Ext_IT9.
  *                The used pin (GPIOx_Pin9) must be configured in input mode.
  *
  *             2- Timers TRGO: TIM2, TIM4, TIM5, TIM6, TIM7 and TIM8 
  *                (DAC_Trigger_T2_TRGO, DAC_Trigger_T4_TRGO...)
  *                The timer TRGO event should be selected using TIM_SelectOutputTrigger()
  *
  *             3- Software using DAC_Trigger_Software
  *
  *          DAC Buffer mode feature
  *          ========================  
  *          Each DAC channel integrates an output buffer that can be used to 
  *          reduce the output impedance, and to drive external loads directly
  *          without having to add an external operational amplifier.
  *          To enable, the output buffer use  
  *              DAC_InitStructure.DAC_OutputBuffer = DAC_OutputBuffer_Enable;
  *          
  *          Refer to the device datasheet for more details about output 
  *          impedance value with and without output buffer.
  *          
  *          DAC wave generation feature
  *          =============================      
  *          Both DAC channels can be used to generate
  *             1- Noise wave using DAC_WaveGeneration_Noise
  *             2- Triangle wave using DAC_WaveGeneration_Triangle
  *        
  *          Wave generation can be disabled using DAC_WaveGeneration_None
  *
  *          DAC data format
  *          ================   
  *          The DAC data format can be:
  *             1- 8-bit right alignment using DAC_Align_8b_R
  *             2- 12-bit left alignment using DAC_Align_12b_L
  *             3- 12-bit right alignment using DAC_Align_12b_R
  *
  *          DAC data value to voltage correspondence  
  *          ========================================  
  *          The analog output voltage on each DAC channel pin is determined
  *          by the following equation: 
  *          DAC_OUTx = VREF+ * DOR / 4095
  *          with  DOR is the Data Output Register
  *                VEF+ is the input voltage reference (refer to the device datasheet)
  *          e.g. To set DAC_OUT1 to 0.7V, use
  *            DAC_SetChannel1Data(DAC_Align_12b_R, 868);
  *          Assuming that VREF+ = 3.3V, DAC_OUT1 = (3.3 * 868) / 4095 = 0.7V
  *
  *          DMA requests 
  *          =============    
  *          A DMA1 request can be generated when an external trigger (but not
  *          a software trigger) occurs if DMA1 requests are enabled using
  *          DAC_DMACmd()
  *          DMA1 requests are mapped as following:
  *             1- DAC channel1 : mapped on DMA1 Stream5 channel7 which must be 
  *                               already configured
  *             2- DAC channel2 : mapped on DMA1 Stream6 channel7 which must be 
  *                               already configured
  *
  *          ===================================================================      
  *                              How to use this driver 
  *          ===================================================================          
  *            - DAC APB clock must be enabled to get write access to DAC
  *              registers using
  *              RCC_APB1PeriphClockCmd(RCC_APB1Periph_DAC, ENABLE)
  *            - Configure DAC_OUTx (DAC_OUT1: PA4, DAC_OUT2: PA5) in analog mode.
  *            - Configure the DAC channel using DAC_Init() function
  *            - Enable the DAC channel using DAC_Cmd() function
  * 
  *  @endverbatim
  *    
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT 2012 STMicroelectronics</center></h2>
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  */ 


/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_dac.h"
#include "stm32f4xx_rcc.h"

/** @addtogroup STM32F4xx_StdPeriph_Driver
  * @{
  */

/** @defgroup DAC 
  * @brief DAC driver modules
  * @{
  */ 

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/

/* CR register Mask */
#define CR_CLEAR_MASK_DAC          ((uint32_t)0x00000FFE)

/* DAC Dual Channels SWTRIG masks */
#define DUAL_SWTRIG_SET            ((uint32_t)0x00000003)
#define DUAL_SWTRIG_RESET          ((uint32_t)0xFFFFFFFC)

/* DHR registers offsets */
#define DHR12R1_OFFSET             ((uint32_t)0x00000008)
#define DHR12R2_OFFSET             ((uint32_t)0x00000014)
#define DHR12RD_OFFSET             ((uint32_t)0x00000020)

/* DOR register offset */
#define DOR_OFFSET                 ((uint32_t)0x0000002C)

/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

/** @defgroup DAC_Private_Functions
  * @{
  */

/** @defgroup DAC_Group1 DAC channels configuration
 *  @brief   DAC channels configuration: trigger, output buffer, data format 
 *
@verbatim   
 ===============================================================================
          DAC channels configuration: trigger, output buffer, data format
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Deinitializes the DAC peripheral registers to their default reset values.
  * @param  None
  * @retval None
  */
void DAC_DeInit(void)
{
  /* Enable DAC reset state */
  RCC_APB1PeriphResetCmd(RCC_APB1Periph_DAC, ENABLE);
  /* Release DAC from reset state */
  RCC_APB1PeriphResetCmd(RCC_APB1Periph_DAC, DISABLE);
}

/**
  * @brief  Initializes the DAC peripheral according to the specified parameters
  *         in the DAC_InitStruct.
  * @param  DAC_Channel: the selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_InitStruct: pointer to a DAC_InitTypeDef structure that contains
  *         the configuration information for the  specified DAC channel.
  * @retval None
  */
void DAC_Init(uint32_t DAC_Channel, DAC_InitTypeDef* DAC_InitStruct)
{
  uint32_t tmpreg1 = 0, tmpreg2 = 0;

  /* Check the DAC parameters */
  assert_param(IS_DAC_TRIGGER(DAC_InitStruct->DAC_Trigger));
  assert_param(IS_DAC_GENERATE_WAVE(DAC_InitStruct->DAC_WaveGeneration));
  assert_param(IS_DAC_LFSR_UNMASK_TRIANGLE_AMPLITUDE(DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude));
  assert_param(IS_DAC_OUTPUT_BUFFER_STATE(DAC_InitStruct->DAC_OutputBuffer));

/*---------------------------- DAC CR Configuration --------------------------*/
  /* Get the DAC CR value */
  tmpreg1 = DAC->CR;
  /* Clear BOFFx, TENx, TSELx, WAVEx and MAMPx bits */
  tmpreg1 &= ~(CR_CLEAR_MASK_DAC << DAC_Channel);
  /* Configure for the selected DAC channel: buffer output, trigger, 
     wave generation, mask/amplitude for wave generation */
  /* Set TSELx and TENx bits according to DAC_Trigger value */
  /* Set WAVEx bits according to DAC_WaveGeneration value */
  /* Set MAMPx bits according to DAC_LFSRUnmask_TriangleAmplitude value */ 
  /* Set BOFFx bit according to DAC_OutputBuffer value */   
  tmpreg2 = (DAC_InitStruct->DAC_Trigger | DAC_InitStruct->DAC_WaveGeneration |
             DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude | \
             DAC_InitStruct->DAC_OutputBuffer);
  /* Calculate CR register value depending on DAC_Channel */
  tmpreg1 |= tmpreg2 << DAC_Channel;
  /* Write to DAC CR */
  DAC->CR = tmpreg1;
}

/**
  * @brief  Fills each DAC_InitStruct member with its default value.
  * @param  DAC_InitStruct: pointer to a DAC_InitTypeDef structure which will 
  *         be initialized.
  * @retval None
  */
void DAC_StructInit(DAC_InitTypeDef* DAC_InitStruct)
{
/*--------------- Reset DAC init structure parameters values -----------------*/
  /* Initialize the DAC_Trigger member */
  DAC_InitStruct->DAC_Trigger = DAC_Trigger_None;
  /* Initialize the DAC_WaveGeneration member */
  DAC_InitStruct->DAC_WaveGeneration = DAC_WaveGeneration_None;
  /* Initialize the DAC_LFSRUnmask_TriangleAmplitude member */
  DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude = DAC_LFSRUnmask_Bit0;
  /* Initialize the DAC_OutputBuffer member */
  DAC_InitStruct->DAC_OutputBuffer = DAC_OutputBuffer_Enable;
}

/**
  * @brief  Enables or disables the specified DAC channel.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  NewState: new state of the DAC channel. 
  *          This parameter can be: ENABLE or DISABLE.
  * @note   When the DAC channel is enabled the trigger source can no more be modified.
  * @retval None
  */
void DAC_Cmd(uint32_t DAC_Channel, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected DAC channel */
    DAC->CR |= (DAC_CR_EN1 << DAC_Channel);
  }
  else
  {
    /* Disable the selected DAC channel */
    DAC->CR &= (~(DAC_CR_EN1 << DAC_Channel));
  }
}

/**
  * @brief  Enables or disables the selected DAC channel software trigger.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  NewState: new state of the selected DAC channel software trigger.
  *          This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void DAC_SoftwareTriggerCmd(uint32_t DAC_Channel, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable software trigger for the selected DAC channel */
    DAC->SWTRIGR |= (uint32_t)DAC_SWTRIGR_SWTRIG1 << (DAC_Channel >> 4);
  }
  else
  {
    /* Disable software trigger for the selected DAC channel */
    DAC->SWTRIGR &= ~((uint32_t)DAC_SWTRIGR_SWTRIG1 << (DAC_Channel >> 4));
  }
}

/**
  * @brief  Enables or disables simultaneously the two DAC channels software triggers.
  * @param  NewState: new state of the DAC channels software triggers.
  *          This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void DAC_DualSoftwareTriggerCmd(FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable software trigger for both DAC channels */
    DAC->SWTRIGR |= DUAL_SWTRIG_SET;
  }
  else
  {
    /* Disable software trigger for both DAC channels */
    DAC->SWTRIGR &= DUAL_SWTRIG_RESET;
  }
}

/**
  * @brief  Enables or disables the selected DAC channel wave generation.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_Wave: specifies the wave type to enable or disable.
  *          This parameter can be one of the following values:
  *            @arg DAC_Wave_Noise: noise wave generation
  *            @arg DAC_Wave_Triangle: triangle wave generation
  * @param  NewState: new state of the selected DAC channel wave generation.
  *          This parameter can be: ENABLE or DISABLE.  
  * @retval None
  */
void DAC_WaveGenerationCmd(uint32_t DAC_Channel, uint32_t DAC_Wave, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_WAVE(DAC_Wave)); 
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected wave generation for the selected DAC channel */
    DAC->CR |= DAC_Wave << DAC_Channel;
  }
  else
  {
    /* Disable the selected wave generation for the selected DAC channel */
    DAC->CR &= ~(DAC_Wave << DAC_Channel);
  }
}

/**
  * @brief  Set the specified data holding register value for DAC channel1.
  * @param  DAC_Align: Specifies the data alignment for DAC channel1.
  *          This parameter can be one of the following values:
  *            @arg DAC_Align_8b_R: 8bit right data alignment selected
  *            @arg DAC_Align_12b_L: 12bit left data alignment selected
  *            @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data: Data to be loaded in the selected data holding register.
  * @retval None
  */
void DAC_SetChannel1Data(uint32_t DAC_Align, uint16_t Data)
{  
  __IO uint32_t tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data));
  
  tmp = (uint32_t)DAC_BASE; 
  tmp += DHR12R1_OFFSET + DAC_Align;

  /* Set the DAC channel1 selected data holding register */
  *(__IO uint32_t *) tmp = Data;
}

/**
  * @brief  Set the specified data holding register value for DAC channel2.
  * @param  DAC_Align: Specifies the data alignment for DAC channel2.
  *          This parameter can be one of the following values:
  *            @arg DAC_Align_8b_R: 8bit right data alignment selected
  *            @arg DAC_Align_12b_L: 12bit left data alignment selected
  *            @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data: Data to be loaded in the selected data holding register.
  * @retval None
  */
void DAC_SetChannel2Data(uint32_t DAC_Align, uint16_t Data)
{
  __IO uint32_t tmp = 0;

  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data));
  
  tmp = (uint32_t)DAC_BASE;
  tmp += DHR12R2_OFFSET + DAC_Align;

  /* Set the DAC channel2 selected data holding register */
  *(__IO uint32_t *)tmp = Data;
}

/**
  * @brief  Set the specified data holding register value for dual channel DAC.
  * @param  DAC_Align: Specifies the data alignment for dual channel DAC.
  *          This parameter can be one of the following values:
  *            @arg DAC_Align_8b_R: 8bit right data alignment selected
  *            @arg DAC_Align_12b_L: 12bit left data alignment selected
  *            @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data2: Data for DAC Channel2 to be loaded in the selected data holding register.
  * @param  Data1: Data for DAC Channel1 to be loaded in the selected data  holding register.
  * @note   In dual mode, a unique register access is required to write in both
  *          DAC channels at the same time.
  * @retval None
  */
void DAC_SetDualChannelData(uint32_t DAC_Align, uint16_t Data2, uint16_t Data1)
{
  uint32_t data = 0, tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data1));
  assert_param(IS_DAC_DATA(Data2));
  
  /* Calculate and set dual DAC data holding register value */
  if (DAC_Align == DAC_Align_8b_R)
  {
    data = ((uint32_t)Data2 << 8) | Data1; 
  }
  else
  {
    data = ((uint32_t)Data2 << 16) | Data1;
  }
  
  tmp = (uint32_t)DAC_BASE;
  tmp += DHR12RD_OFFSET + DAC_Align;

  /* Set the dual DAC selected data holding register */
  *(__IO uint32_t *)tmp = data;
}

/**
  * @brief  Returns the last data output value of the selected DAC channel.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @retval The selected DAC channel data output value.
  */
uint16_t DAC_GetDataOutputValue(uint32_t DAC_Channel)
{
  __IO uint32_t tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  
  tmp = (uint32_t) DAC_BASE ;
  tmp += DOR_OFFSET + ((uint32_t)DAC_Channel >> 2);
  
  /* Returns the DAC channel data output register value */
  return (uint16_t) (*(__IO uint32_t*) tmp);
}
/**
  * @}
  */

/** @defgroup DAC_Group2 DMA management functions
 *  @brief   DMA management functions
 *
@verbatim   
 ===============================================================================
                          DMA management functions
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Enables or disables the specified DAC channel DMA request.
  * @note   When enabled DMA1 is generated when an external trigger (EXTI Line9,
  *         TIM2, TIM4, TIM5, TIM6, TIM7 or TIM8  but not a software trigger) occurs.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  NewState: new state of the selected DAC channel DMA request.
  *          This parameter can be: ENABLE or DISABLE.
  * @note   The DAC channel1 is mapped on DMA1 Stream 5 channel7 which must be
  *          already configured.
  * @note   The DAC channel2 is mapped on DMA1 Stream 6 channel7 which must be
  *          already configured.    
  * @retval None
  */
void DAC_DMACmd(uint32_t DAC_Channel, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected DAC channel DMA request */
    DAC->CR |= (DAC_CR_DMAEN1 << DAC_Channel);
  }
  else
  {
    /* Disable the selected DAC channel DMA request */
    DAC->CR &= (~(DAC_CR_DMAEN1 << DAC_Channel));
  }
}
/**
  * @}
  */

/** @defgroup DAC_Group3 Interrupts and flags management functions
 *  @brief   Interrupts and flags management functions
 *
@verbatim   
 ===============================================================================
                   Interrupts and flags management functions
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Enables or disables the specified DAC interrupts.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_IT: specifies the DAC interrupt sources to be enabled or disabled. 
  *          This parameter can be the following values:
  *            @arg DAC_IT_DMAUDR: DMA underrun interrupt mask
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).
  * @param  NewState: new state of the specified DAC interrupts.
  *          This parameter can be: ENABLE or DISABLE.
  * @retval None
  */ 
void DAC_ITConfig(uint32_t DAC_Channel, uint32_t DAC_IT, FunctionalState NewState)  
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  assert_param(IS_DAC_IT(DAC_IT)); 

  if (NewState != DISABLE)
  {
    /* Enable the selected DAC interrupts */
    DAC->CR |=  (DAC_IT << DAC_Channel);
  }
  else
  {
    /* Disable the selected DAC interrupts */
    DAC->CR &= (~(uint32_t)(DAC_IT << DAC_Channel));
  }
}

/**
  * @brief  Checks whether the specified DAC flag is set or not.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_FLAG: specifies the flag to check. 
  *          This parameter can be only of the following value:
  *            @arg DAC_FLAG_DMAUDR: DMA underrun flag
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).
  * @retval The new state of DAC_FLAG (SET or RESET).
  */
FlagStatus DAC_GetFlagStatus(uint32_t DAC_Channel, uint32_t DAC_FLAG)
{
  FlagStatus bitstatus = RESET;
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_FLAG(DAC_FLAG));

  /* Check the status of the specified DAC flag */
  if ((DAC->SR & (DAC_FLAG << DAC_Channel)) != (uint8_t)RESET)
  {
    /* DAC_FLAG is set */
    bitstatus = SET;
  }
  else
  {
    /* DAC_FLAG is reset */
    bitstatus = RESET;
  }
  /* Return the DAC_FLAG status */
  return  bitstatus;
}

/**
  * @brief  Clears the DAC channel's pending flags.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_FLAG: specifies the flag to clear. 
  *          This parameter can be of the following value:
  *            @arg DAC_FLAG_DMAUDR: DMA underrun flag 
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).                           
  * @retval None
  */
void DAC_ClearFlag(uint32_t DAC_Channel, uint32_t DAC_FLAG)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_FLAG(DAC_FLAG));

  /* Clear the selected DAC flags */
  DAC->SR = (DAC_FLAG << DAC_Channel);
}

/**
  * @brief  Checks whether the specified DAC interrupt has occurred or not.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_IT: specifies the DAC interrupt source to check. 
  *          This parameter can be the following values:
  *            @arg DAC_IT_DMAUDR: DMA underrun interrupt mask
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).
  * @retval The new state of DAC_IT (SET or RESET).
  */
ITStatus DAC_GetITStatus(uint32_t DAC_Channel, uint32_t DAC_IT)
{
  ITStatus bitstatus = RESET;
  uint32_t enablestatus = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_IT(DAC_IT));

  /* Get the DAC_IT enable bit status */
  enablestatus = (DAC->CR & (DAC_IT << DAC_Channel)) ;
  
  /* Check the status of the specified DAC interrupt */
  if (((DAC->SR & (DAC_IT << DAC_Channel)) != (uint32_t)RESET) && enablestatus)
  {
    /* DAC_IT is set */
    bitstatus = SET;
  }
  else
  {
    /* DAC_IT is reset */
    bitstatus = RESET;
  }
  /* Return the DAC_IT status */
  return  bitstatus;
}

/**
  * @brief  Clears the DAC channel's interrupt pending bits.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_IT: specifies the DAC interrupt pending bit to clear.
  *          This parameter can be the following values:
  *            @arg DAC_IT_DMAUDR: DMA underrun interrupt mask                         
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).                           
  * @retval None
  */
void DAC_ClearITPendingBit(uint32_t DAC_Channel, uint32_t DAC_IT)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_IT(DAC_IT)); 

  /* Clear the selected DAC interrupt pending bits */
  DAC->SR = (DAC_IT << DAC_Channel);
}

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/