Skip to content

Latest commit

 

History

History
346 lines (255 loc) · 13.5 KB

README.md

File metadata and controls

346 lines (255 loc) · 13.5 KB
Raw

Mightyboard Rev G and H support - Fork of Klipper3d/klipper

This fork adds support for Makerbot Replicator 2/2X (Mightyboard Rev G and H) and some clones.

STATUS - I would consider master to be production ready. Everything that can be supported is at this point and all features are working. This has been tested on a number of printers and more wide spread testing would be appreciated.

Supported Clones - Currently, no clones have example config files or instructions for flashing Klipper. If you have a Replicator clone that uses k type thermocouples and/or an ADS1118 ADC chip and want to get Klipper running on it let me know and submit a sample config file and flashing instructions and I will include them in this repo.

Printers that may use ADS1118 ADCs and may work with this repo include:

  • FlashForge Dreamer NX
  • FlashForge Dreamer
  • FlashForge Inventor
  • Dremel 3D20
  • Dremel 3D40 (known to work)
  • PowerSpec Ultra 3D
  • Monoprice Inventor 1

Changes include:

  • Documents what is necessary to flash the MCU (57600 baud and correct avrdude protocol)
  • Adds support for MCU reset (toggle connection baud rate to 57600)
  • Adds support for ADS1118 and k-type thermocouples (one or two extruders)
  • Adds support for hardware blinking of the LEDs
  • Adds support for multiple buttons with same action in display
  • Removes the need for specifying dummy pins for software spi devices
  • Adds example g code macros to emulate some original Makerbot behaviors

Example Configs:

/config/printer-makerbot-replicator2-2012.cfg can be used as a starting point for the Replicator 2.

/config/printer-makerbot-replicator2x-2012.cfg can be used as a starting point for the Replicator 2X.

Installation

KIAUH

NOTE: KIAUH takes a little bit more work to set up, but is ideal for running multiple instances of klipper, and also makes it possible to install any and all frontends including Mainsail, Fluidd, and Octoprint! A huge thanks to th33xitus for making KIAUH!

Step 1:

Follow the instruction on KIAUH's github page to install both the recommended operating system for KIAUH and the script itself.

Step 2:

KIAUH is set by default to install klipper from the klipper3d repo, however, we need to install it from the dockterj branch. This can be accomplished by editing the file klipper_repos.txt.example.

SSH into your raspberry pi, and run the following commands:

cd kiauh
sudo nano klipper_repos.txt.example

Now, you should be presented with a screen that looks like this:

Delete the four uncommented lines, and add the line https://github.com/dockterj/klipper in their place. Your screen should now look like this:

Now, hit Control+x to exit, then hit y to save the modified buffer.

You must save the file as klipper_repos.txt, otherwise KIAUH will not recognize the file as valid.

Hit y to save the file under a different name.

If you want to check to be sure the edit was successful, you can type ls into the command line. If the file klipper_repos.txt is there, then the edit was successful.

Step 3:

Now you're ready to start KIAUH! Enter ./kiauh/kiauh.sh to start the script.

Once in KIAUH, you should see a screen like this:

KIAUH, by default, uses the official master branch of klipper. To tell KIAUH to use this branch instead, we need to add the custom repo you created to KIAUH.

Input the number 6 to enter KIAUH's settings, then hit enter. You should now see a screen like this:

Input 1 to set the custom repository. You'll see a screen like this:

Input 0 to set the custom repository, you'll be presented with a screen like this:

Then input b and b again to get back to the main menu.

Step 4:

Now you can install Klipper! Input 1 to get to the installation menu. Once there, input 1 again to enter the klipper installation procedure.

Input 1 to install python 3.x, then set the number of Klipper instances your would like to install.

You may be presented with a prompt like this:

Input y for this prompt to avoid potential problems down the road.

Let the process complete, and now Klipper is fully installed! From here you can install Moonraker, your interface of choice, and whatever other programs you may want that KIAUH offers.

Step 5:

Depending on the printer that you are running, you will either want to use the /config/printer-makerbot-replicator2-2012.cfg config file or the /config/printer-makerbot-replicator2x-2012.cfg config file.

Mainsail and Fluidd both allow you to copy over example configs from within the web interface, however, Octoprint does not. These following steps will detail the process of doing this through the ssh terminal. If this does not apply to you, you can skip to the next step.

If you are still in KIAUH, input Q to close it, then type cd to navigate back to the pi directory, which is represented by a ~. The text preceding your cursor will look similar to pi@replicator2x:~ $

Type cd klipper/config into the command line. You are now in Klipper's example config folder. Type either cp printer-makerbot-replicator2-2012.cfg ~/printer_data/config/ or cp printer-makerbot-replicator2x-2012.cfg ~/printer_data/config/ to copy the example config for your printer into your printer's configuration directory.

Now type cd ~/printer_data/config to move over to your printer's configuration directory. Type rm printer.cfg to remove the placeholder printer config that comes with klipper. Now type mv printer-makerbot-replicator2-2012.cfg printer.cfg or mv printer-makerbot-replicator2x-2012.cfg printer.cfg, depening on your printer, to rename the example config to the config name recognized by Klipper.

Step 6:

Now we're going to flash Klipper to the printer's mainboard.

Plug the printer into one of the Pi's usb ports. Verify that the device appears in /dev/serial/by-id by executing the command ls /dev/serial/by-id. If the printer is connected, this command will return a dialogue that looks like this:

Copy this by highlighting it, then right clicking it. Open up a temporary notepad document and paste it into that, you'll need this to update your printer.cfg.

Find the section of your config that looks like this:

[mcu]
serial: dev/serial/by-id/[your-serial-id-here]
restart_method: mightyboard
baud: 250000

Update the serial: [your-serial-id-here] line with the line you saved earlier. When completed the line should look similar to:

serial: /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_5533034353435160A141-if00

Now, go back to the command line and run:

cd ~/klipper/
make menuconfig

In this menu, choose the atmega1280, 16mhz, and uart0.

Note: See below for the note about atmega2560.

Once you enter those settings, hit Q to exit, then Y to save.

Now run the command make. This will build the firmware for your particular machine.

Now, run the commands:

sudo service klipper stop
make flash FLASH_DEVICE=/dev/serial/by-id/dev/serial/by-id/[your-serial-id-here]
sudo service klipper start

Where an example of FLASH_DEVICE will look like:

FLASH_DEVICE=/dev/serial/by-id/dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_5533034353435160A141-if00

This will flash your printer. If it fails, you may need to power off and then power on your printer, or attempt to connect and disconnect with Klipper. It should flash after you try one or both of these things.

Congratulations! You now have Klipper installed on your Replicator 2 or 2X! Head over to https://www.klipper3d.org/ for documentation on futher tuning of your printer and to learn the specifics of what Klipper is capable of.

Mainsail OS

NOTE: You can use any frontend and install method you want. The only changes needed from this repo are already built into Klipper.

NOTE: There is a bug in Mainsail OS v1.0.1 that will cause the wifi connection to bounce up and down until Sonar is updated. To work around this bug, once the Pi has booted IMMEDIATELY SSH into the Pi and execute systemctl stop sonar. After that navigate to the Machine page and update all components.

Create an SD card with Mainsail OS using Raspberry Pi Imager [Follow the instructions from Mainsail OS].

SSH into the Pi (user pi, password is what you set up when you created the SD card). Execute the following commands:

mv klipper klipper-orig
git clone https://github.com/dockterj/klipper
systemctl restart klipper

At this point if you refresh the update manager on the machine page it will say that klipper is invalid. Ignore this and don't click on "hard recovery" or "soft recovery". Klipper should also report ERROR. This is normal as there is no printer configured yet.

Copy /config/printer-makerbot-replicator2-2012.cfg or /config/printer-makerbot-replicator2x-2012.cfg to printer.cfg. An easy way to do this is to change the root directory in Config File (on the Machine tab) to config_examples. Find printer-makerbot-replicator2-2012.cfg or printer-makerbot-replicator2x-2012.cfg, right click and download it. Change the root directory back to config, upload that file, then rename it printer.cfg.

Plug the printer into the Pi's usb port and verify that the device appears in /dev/serial/by-id by executing the following:

ls /dev/serial/by-id

It should return a line similar to the following:

/dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_A413936383135181D010-if00

Make a note of this so that you can update printer.cfg in the next steps.

You can edit printer.cfg to add/remove features specific to your printer (e.g. remove HBP, change the HBP sensor to match what you have, change x,y, and z limits, etc...). Update the serial: line under the [mcu] section to match the filename found in the previous step. Add the following line at the top of your printer.cfg to enable Mainsail support.

[include mainsail.cfg]

Click Save and Restart.

Following the normal installation steps, run make menuconfig. Choose an atmega1280, 16mhz, and uart0. (see below for note about atmega2560).

Edit src/svr/Makefile and change the line that sets FLASH_DEVICE to point to your mcu (the same /dev/serial/by-id that you changed in printer.cfg). Save your changes.

Run make flash. This should flash your mightyboard. If not, I have found times where I needed to power the mightboard off and back on or attempt to connect and disconnect with Klipper (i.e. connect at a speed other than 57600 first) before it would flash.

At this point you should have Klipper running on your Replicator.

Follow the normal Klipper documentation for further tuning.

Notes

  • The Sailfish firmware has profiles for Mightyboard Rev G and Rev H printers that have an atmega2560 instead of an atmega1280. If you have one of these please let me know so I can get a known working config for them. I believe you should be able to get this working by changing the MCU processor in make menuconfig, editing src/arv/Makefile, and changing the last line from -C stk500v1 to -C stk500v2. Software reset should work but needs to be tested to confirm.

  • The generic-mightyboard.cfg in the main repo should NOT be use for these printers. That config file is for the original Makerbot Replicator and clones and does not work with printers that have ADS1118 ADC and thermocouples (Rep2 and Rep2X).

  • There is no specific error for a disconnected thermocouple, however the printer will shut down if a thermocouple is not attached (this triggers a temperature out of range error).

  • The included printer.cfg changes the origin (0,0) to be in the left front of the build plate to be consistent with other cartesian printers. Keeping the original Replicator origin (which resembles a delta printer, i.e. origin is in the center of the bed) requires updating position_min, position_max, position_endstop, and bed_screws values for the x and y axes.

  • Please watch or star this repo if you are interested. The more people that use this the better the chances of getting it included upstream. Feel free to file issues in this repo for questions or problems (DON'T USE ISSUES IN UPSTREAM FOR THIS)

Welcome to the Klipper project!

Klipper

https://www.klipper3d.org/

Klipper is a 3d-Printer firmware. It combines the power of a general purpose computer with one or more micro-controllers. See the features document for more information on why you should use Klipper.

To begin using Klipper start by installing it.

Klipper is Free Software. See the license or read the documentation. We depend on the generous support from our sponsors.