how to create raid10

[niqiaoqiao]

how to create raid10
./drp-raid ????
disk message
[
{
"ID": "0",
"Driver": "perccli",
"PCI": {
"Bus": 2,
"Device": 0,
"Function": 0
},
"AutoJBOD": true,
"JBODCapable": true,
"RaidCapable": false,
"RaidLevels": [
"jbod"
],
"Volumes": [],
"Disks": [],
"Info": {
"A rollback operation is in progress": "No",
"Abort CC on Error": "Yes",
"Access Policy": "Yes",
"Alarm": "Missing",
"Alarm Control": "Yes",
"Allow Boot with Preserved Cache": "Off",
"Allow Ctrl Encryption": "No",
"Allow Mixed Redundancy on Array": "No",
"Any Offline VD Cache Preserved": "No",
"At least one PFK exists in NVRAM": "No",
"Auto Enhanced Import": "No",
"Auto Rebuild": "On",
"Auto detect BackPlane": "SGPIO/i2c SEP",
"BBU": "Present",
"BBU Status": "8288",
"BGI Rate": "Yes",
"BIOS Enumerate VDs": "1",
"Backend Port Count": "8",
"Battery Warning": "On",
"Battery learn Reoccurrence": "2160 hrs",
"BatteryFRU": "N/A",
"Bios Version": "5.38.00_4.12.05.00_0x05260000",
"Bios was not detected during boot": "No",
"Block SSD Write Disk Cache Change": "No",
"Boot Block Version": "2.03.00.00-0004",
"Bootloader Version": "06.253.57.219",
"BreakMirror RAID Support": "single span R1",
"Bus Number": "2",
"CC Rate": "Yes",
"Cache When BBU Bad": "Off",
"CacheVault Flash Size": "NA",
"Cached IO": "Off",
"Capability": "Not Supported",
"ChipRevision": "D1",
"Cluster Active": "No",
"Cluster Permitted": "No",
"Cluster Support": "No",
"Coercion Mode": "128 MB",
"Consistency Check Reoccurrence": "168 hrs",
"Controller": "0",
"Controller Status": "Optimal",
"Controller has booted into safe mode": "No",
"Controller must be rebooted to complete security operation": "No",
"Controller shutdown required": "No",
"Ctrl temperature(Degree Celsius)": "50",
"Ctrl-R Version": "4.03-0002",
"Current Controller Date/Time": "01/26/2021, 10:15:49",
"Current Size of CacheCade (GB)": "0",
"Current Size of FW Cache (MB)": "382",
"Current System Date/time": "01/26/2021, 18:15:48",
"Dedicated Hot Spare": "Yes",
"Dedicated HotSpares Limited": "No",
"Default spin down time (mins)": "30",
"Delay Among Spinup Groups (sec)": "12",
"Delay during POST": "0",
"Deny CC": "No",
"Deny Clear": "Yes",
"Deny Force Failed": "No",
"Deny Force Good/Bad": "No",
"Deny Locate": "No",
"Deny Missing Replace": "No",
"Deny SCSI Passthrough": "No",
"Deny SMP Passthrough": "No",
"Deny STP Passthrough": "No",
"Device Id": "0x5B",
"Device Interface": "SAS-6G",
"Device Number": "0",
"Direct PD Mapping": "Yes",
"Dirty LED Shows Drive Activity": "No",
"Disable Join Mirror": "Yes",
"Disable Online Controller Reset": "No",
"Disable Online PFK Change": "No",
"Disable Puncturing": "No",
"DisableHII": "No",
"Disk Cache Policy": "Yes",
"Domain ID": "0",
"Drive Coercion Mode": "128MB",
"Driver Name": "megaraid_sas",
"Driver Version": "07.702.06.00-rh2",
"ECC Bucket Count": "0",
"ECC Bucket Leak Rate (hrs)": "4",
"ECC Bucket Size": "255",
"Enable BIOS": "Yes",
"Enable Ctrl-R": "Yes",
"Enable LDBBM": "Yes",
"Enable LED Header": "No",
"Enable PreBoot CLI": "No",
"Enable SCSI Unmap": "Yes",
"Enable Shield State": "No",
"Enable Snapdump": "No",
"Enable SystemPD": "No",
"Enable Web BIOS": "No",
"EnableCrashDump": "No",
"EnableLDBBM": "Yes",
"Enclosures": "1",
"Expose Enclosure Devices": "No",
"Extended LD": "No",
"FDE Drive Mix Support": "No",
"FW and Event Time in GMT": "No",
"Failed to get lock key on bootup": "No",
"Firmware Package Build": "21.2.0-0007",
"Firmware Version": "3.130.05-2086",
"Flash Size": "16MB",
"Flush Time(Default)": "4s",
"Force Offline": "Yes",
"Force Online": "Yes",
"Force Rebuild": "Yes",
"Foreign Config Import": "Yes",
"Front End Port Count": "0",
"Function Number": "0",
"Global Hot Spares": "Yes",
"Headless Mode": "Yes",
"Host Interface": "PCI-E",
"IO Policy": "Yes",
"Image name": "No pending images",
"LED Show Drive Activity": "Yes",
"Load Balance Mode": "Auto",
"Lock Key Assigned": "No",
"Lock key has not been backed up": "No",
"Maintain PD Fail History": "No",
"Max Arms Per VD": "32",
"Max Arrays": "128",
"Max Chained Enclosures": "4",
"Max Configurable CacheCade Size(GB)": "512",
"Max Data Transfer Size": "8192 sectors",
"Max Drives to Spinup at One Time": "4",
"Max Number of VDs": "64",
"Max Parallel Commands": "1008",
"Max SGE Count": "60",
"Max Spans Per VD": "8",
"Max Strip Size": "1.000 MB",
"Max Strips PerIO": "42",
"Max Transportable DGs": "0",
"Max VD per array": "16",
"Maximum number of direct attached drives to spin up in 1 min": "20",
"Memory Correctable Errors": "0",
"Memory Uncorrectable Errors": "0",
"Mfg Date": "09/08/13",
"Min Strip Size": "64 KB",
"Mix in Enclosure": "Allowed",
"Mix of SAS/SATA of HDD type in VD": "Not Allowed",
"Mix of SAS/SATA of SSD type in VD": "Not Allowed",
"Mix of SSD/HDD in VD": "Not Allowed",
"Model": "PERC H710 Mini",
"NCQ": "No",
"NVDATA Version": "2.1108.03-0095",
"NVRAM Size": "32KB",
"Next Consistency check launch": "NA",
"Next Patrol Read launch": "01/30/2021, 03:00:00",
"OEMID": "Dell",
"On Board Expander": "Absent",
"On Board Memory Size": "512MB",
"PCI Address": "00:02:00:00",
"PD Firmware Download in progress": "No",
"Patrol Read Rate": "Yes",
"Patrol Read Reoccurrence": "168 hrs",
"Performance Metrics": "Yes",
"Phy Polarity": "0",
"Phy PolaritySplit": "0",
"Physical Drives": "8",
"Point In Time Progress": "No",
"Power Saving option": "Enabled",
"Power Savings": "Yes",
"Preboot CLI Version": "05.00-03:#%00008",
"RAID Level Supported": "RAID0, RAID1, RAID5, RAID6, RAID00, RAID10(2 or more drives per span), RAID50, RAID60",
"ROC temperature(Degree Celsius)": "50",
"Read Policy": "Adaptive",
"Real Time Scheduler": "No",
"Rebuild Rate": "Yes",
"Reconstruct Rate": "Yes",
"Reconstruction": "Yes",
"Reorder Host Requests": "On",
"Restore Hot Spare on Insertion": "No",
"Revertible Hot Spares": "Yes",
"Revision No": "A03",
"Rework Date": "09/08/13",
"SAS Address": "5b8ca3a0f99e5100",
"SAS Disable": "No",
"SMART Mode": "Mode 6",
"SSC Policy is WB": "No",
"Security Key Assigned": "Off",
"Self Diagnostic": "Yes",
"Serial Debugger": "Present",
"Serial Number": "39704H0",
"Set Power State For Cfg": "No",
"Snapshot Enabled": "No",
"Spanning": "Yes",
"Spin Down Mode": "None",
"Stop BIOS on Error": "On",
"Strip Size": "64 KB",
"SubDevice Id": "0x1F38",
"SubVendor Id": "0x1028",
"Support AES Encryption Algorithm": "No",
"Support Allowed Operations": "Yes",
"Support Boot Time PFK Change": "No",
"Support Breakmirror": "Yes",
"Support CPLDUpdate": "No",
"Support Clear Snapdump": "No",
"Support Config Auto Balance": "No",
"Support Config Page Model": "Yes",
"Support Ctrl Info Extended": "No",
"Support Debug Queue": "No",
"Support Degraded Media": "No",
"Support Diagnostic results": "No",
"Support DisableImmediateIO": "No",
"Support Drive Crypto Erase": "No",
"Support DrvActivityLEDSetting": "No",
"Support Dual Fw Image": "No",
"Support EKM": "No",
"Support Emergency Spares": "No",
"Support Emulated Drives": "No",
"Support Enclosure Enumeration": "Yes",
"Support Encrypted MFC": "No",
"Support Enhanced Foreign Import": "Yes",
"Support Ext Enclosure": "No",
"Support Extended Drive performance Monitoring": "No",
"Support FastPath": "Yes",
"Support FlushWriteVerify": "No",
"Support Force Personality Change": "No",
"Support ForceFlash": "No",
"Support ForceTo512e": "No",
"Support IButton less": "No",
"Support JBOD Write cache": "No",
"Support Lane DeviceType": "No",
"Support Lane current speed": "No",
"Support Large QD Support": "No",
"Support LargeIOSupport": "No",
"Support Ld BBM Info": "No",
"Support Least Latency Mode": "Yes",
"Support Maintenance Mode": "No",
"Support Max Rate SATA": "No",
"Support Multipath": "Yes",
"Support NVMe Width": "No",
"Support Odd \u0026 Even Drive count in RAID1E": "No",
"Support OnDemand Snapdump": "No",
"Support PD Firmware Download": "Yes",
"Support PFK": "No",
"Support PHY current speed": "No",
"Support PI": "No",
"Support PSOC Update": "No",
"Support Parallel FW Update": "No",
"Support Perf Tuning": "Yes",
"Support Power State": "Yes",
"Support Powersave Max With Cache": "No",
"Support Reset Now": "No",
"Support SSC Association": "No",
"Support SSC WriteBack": "No",
"Support SSD PatrolRead": "No",
"Support SSD Wear Gauge": "No",
"Support Secure Boot": "No",
"Support Security": "Yes",
"Support SecurityonJBOD": "No",
"Support Sesmonitoring": "No",
"Support Set Link Speed": "No",
"Support Shield State": "No",
"Support Snapdump": "No",
"Support Suspend Resume BG ops": "No",
"Support SystemPD": "No",
"Support T10 Power State": "Yes",
"Support Temperature": "Yes",
"Support Uneven span": "No",
"Support VD Cachebypass": "No",
"Support VD Hide": "No",
"Support VD Scsi Unmap": "No",
"Support VD discardCacheDuringLDDelete": "No",
"Support discardCacheDuringLDDelete": "No",
"Support more than 8 Phys": "Yes",
"Support the OCE without adding drives": "Yes",
"Supported Drives": "SAS, SATA",
"TPM": "Absent",
"TTY Log In Flash": "No",
"Temperature Sensor for Controller": "Present",
"Temperature Sensor for ROC": "Present",
"Time taken to detect CME": "60 sec",
"Topology Type": "None",
"Treat Single span R1E as R10": "Yes",
"Un-Certified Hard Disk Drives": "Allow",
"Upgradable CPLD": "Absent",
"Upgradable PSOC": "Absent",
"Upgrade Key": "Absent",
"Use drive activity for locate": "Off",
"VD PowerSave Policy": "Controller Defined",
"Vendor Id": "0x1000",
"Write Policy": "WB",
"ZCR Config": "Unknown",
"Zero Based Enclosure Enumeration": "Yes"
}
},
{
"ID": "0",
"Driver": "megacli",
"PCI": {
"Bus": 29056,
"Device": 0,
"Function": 160
},
"AutoJBOD": false,
"JBODCapable": false,
"RaidCapable": true,
"RaidLevels": [
"raid0",
"raid1",
"raid5",
"raid6",
"raid00",
"raid10",
"raid50",
"raid60"
],
"Volumes": [],
"Disks": [
{
"ControllerID": "0",
"ControllerDriver": "megacli",
"VolumeID": "",
"Enclosure": "32",
"Size": 299439751168,
"UsedSize": 0,
"SectorCount": 584843264,
"PhysicalSectorSize": 0,
"LogicalSectorSize": 0,
"Slot": 0,
"Protocol": "sas",
"MediaType": "disk",
"Status": "Unconfigured(good), Spun Up",
"JBOD": false,
"Info": {
"Coerced Size": "278.875 GB [0x22dc0000 Sectors]",
"Connected Port Number": "3(path0)",
"Device Firmware Level": "D1S6",
"Device Id": "0",
"Device Speed": "6.0Gb/s",
"Drive has flagged a S.M.A.R.T alert": "No",
"Drive is formatted for PI information": "No",
"Enclosure Device ID": "32",
"Enclosure position": "1",
"FDE Capable": "Not Capable",
"FDE Enable": "Disable",
"Firmware state": "Unconfigured(good), Spun Up",
"Foreign State": "None",
"Inquiry Data": "WD WD3001BKHG D1S6WXU1E13VTSE7",
"Last Predictive Failure Event Seq Number": "0",
"Link Speed": "6.0Gb/s",
"Locked": "Unlocked",
"Media Error Count": "0",
"Media Type": "Hard Disk Device",
"Needs EKM Attention": "No",
"Non Coerced Size": "278.896 GB [0x22dcb25c Sectors]",
"Other Error Count": "0",
"PD Type": "SAS",
"PI": "No PI",
"PI Eligibility": "No",
"Port status": "Active",
"Port's Linkspeed": "6.0Gb/s",
"Predictive Failure Count": "0",
"Raw Size": "279.396 GB [0x22ecb25c Sectors]",
"SAS Address(0)": "0x50000c0f021966aa",
"SAS Address(1)": "0x0",
"Sector Size": "0",
"Secured": "Unsecured",
"Sequence Number": "3",
"Shield Counter": "0",
"Slot Number": "0",
"Successful diagnostics completion on": "N/A",
"WWN": "50000C0F021966A9"
}
},
{
"ControllerID": "0",
"ControllerDriver": "megacli",
"VolumeID": "",
"Enclosure": "32",
"Size": 299439751168,
"UsedSize": 0,
"SectorCount": 584843264,
"PhysicalSectorSize": 0,
"LogicalSectorSize": 0,
"Slot": 1,
"Protocol": "sas",
"MediaType": "disk",
"Status": "Unconfigured(good), Spun Up",
"JBOD": false,
"Info": {
"Coerced Size": "278.875 GB [0x22dc0000 Sectors]",
"Connected Port Number": "4(path0)",
"Device Firmware Level": "D1S6",
"Device Id": "1",
"Device Speed": "6.0Gb/s",
"Drive has flagged a S.M.A.R.T alert": "No",
"Drive is formatted for PI information": "No",
"Enclosure Device ID": "32",
"Enclosure position": "1",
"FDE Capable": "Not Capable",
"FDE Enable": "Disable",
"Firmware state": "Unconfigured(good), Spun Up",
"Foreign State": "None",
"Inquiry Data": "WD WD3001BKHG D1S6WXU1E13VTSC2",
"Last Predictive Failure Event Seq Number": "0",
"Link Speed": "6.0Gb/s",
"Locked": "Unlocked",
"Media Error Count": "0",
"Media Type": "Hard Disk Device",
"Needs EKM Attention": "No",
"Non Coerced Size": "278.896 GB [0x22dcb25c Sectors]",
"Other Error Count": "0",
"PD Type": "SAS",
"PI": "No PI",
"PI Eligibility": "No",
"Port status": "Active",
"Port's Linkspeed": "6.0Gb/s",
"Predictive Failure Count": "0",
"Raw Size": "279.396 GB [0x22ecb25c Sectors]",
"SAS Address(0)": "0x50000c0f02764ab2",
"SAS Address(1)": "0x0",
"Sector Size": "0",
"Secured": "Unsecured",
"Sequence Number": "3",
"Shield Counter": "0",
"Slot Number": "1",
"Successful diagnostics completion on": "N/A",
"WWN": "50000C0F02764AB1"
}
},
{
"ControllerID": "0",
"ControllerDriver": "megacli",
"VolumeID": "",
"Enclosure": "32",
"Size": 299439751168,
"UsedSize": 0,
"SectorCount": 584843264,
"PhysicalSectorSize": 0,
"LogicalSectorSize": 0,
"Slot": 2,
"Protocol": "sas",
"MediaType": "disk",
"Status": "Unconfigured(good), Spun Up",
"JBOD": false,
"Info": {
"Coerced Size": "278.875 GB [0x22dc0000 Sectors]",
"Connected Port Number": "5(path0)",
"Device Firmware Level": "D1S6",
"Device Id": "2",
"Device Speed": "6.0Gb/s",
"Drive has flagged a S.M.A.R.T alert": "No",
"Drive is formatted for PI information": "No",
"Enclosure Device ID": "32",
"Enclosure position": "1",
"FDE Capable": "Not Capable",
"FDE Enable": "Disable",
"Firmware state": "Unconfigured(good), Spun Up",
"Foreign State": "None",
"Inquiry Data": "WD WD3001BKHG D1S6WXU1E13VTMJ7",
"Last Predictive Failure Event Seq Number": "0",
"Link Speed": "6.0Gb/s",
"Locked": "Unlocked",
"Media Error Count": "0",
"Media Type": "Hard Disk Device",
"Needs EKM Attention": "No",
"Non Coerced Size": "278.896 GB [0x22dcb25c Sectors]",
"Other Error Count": "0",
"PD Type": "SAS",
"PI": "No PI",
"PI Eligibility": "No",
"Port status": "Active",
"Port's Linkspeed": "6.0Gb/s",
"Predictive Failure Count": "0",
"Raw Size": "279.396 GB [0x22ecb25c Sectors]",
"SAS Address(0)": "0x50000c0f02196b12",
"SAS Address(1)": "0x0",
"Sector Size": "0",
"Secured": "Unsecured",
"Sequence Number": "3",
"Shield Counter": "0",
"Slot Number": "2",
"Successful diagnostics completion on": "N/A",
"WWN": "50000C0F02196B11"
}
},
{
"ControllerID": "0",
"ControllerDriver": "megacli",
"VolumeID": "",
"Enclosure": "32",
"Size": 299439751168,
"UsedSize": 0,
"SectorCount": 584843264,
"PhysicalSectorSize": 0,
"LogicalSectorSize": 0,
"Slot": 3,
"Protocol": "sas",
"MediaType": "disk",
"Status": "Unconfigured(good), Spun Up",
"JBOD": false,
"Info": {
"Coerced Size": "278.875 GB [0x22dc0000 Sectors]",
"Connected Port Number": "6(path0)",
"Device Firmware Level": "D1S6",
"Device Id": "3",
"Device Speed": "6.0Gb/s",
"Drive has flagged a S.M.A.R.T alert": "No",
"Drive is formatted for PI information": "No",
"Enclosure Device ID": "32",
"Enclosure position": "1",
"FDE Capable": "Not Capable",
"FDE Enable": "Disable",
"Firmware state": "Unconfigured(good), Spun Up",
"Foreign State": "None",
"Inquiry Data": "WD WD3001BKHG D1S6WXU1E13VVFT1",
"Last Predictive Failure Event Seq Number": "0",
"Link Speed": "6.0Gb/s",
"Locked": "Unlocked",
"Media Error Count": "0",
"Media Type": "Hard Disk Device",
"Needs EKM Attention": "No",
"Non Coerced Size": "278.896 GB [0x22dcb25c Sectors]",
"Other Error Count": "0",
"PD Type": "SAS",
"PI": "No PI",
"PI Eligibility": "No",
"Port status": "Active",
"Port's Linkspeed": "6.0Gb/s",
"Predictive Failure Count": "0",
"Raw Size": "279.396 GB [0x22ecb25c Sectors]",
"SAS Address(0)": "0x50000c0f021968ca",
"SAS Address(1)": "0x0",
"Sector Size": "0",
"Secured": "Unsecured",
"Sequence Number": "3",
"Shield Counter": "0",
"Slot Number": "3",
"Successful diagnostics completion on": "N/A",
"WWN": "50000C0F021968C9"
}
},
{
"ControllerID": "0",
"ControllerDriver": "megacli",
"VolumeID": "",
"Enclosure": "32",
"Size": 299439751168,
"UsedSize": 0,
"SectorCount": 584843264,
"PhysicalSectorSize": 0,
"LogicalSectorSize": 0,
"Slot": 4,
"Protocol": "sas",
"MediaType": "disk",
"Status": "Unconfigured(good), Spun Up",
"JBOD": false,
"Info": {
"Coerced Size": "278.875 GB [0x22dc0000 Sectors]",
"Connected Port Number": "0(path0)",
"Device Firmware Level": "D1S6",
"Device Id": "4",
"Device Speed": "6.0Gb/s",
"Drive has flagged a S.M.A.R.T alert": "No",
"Drive is formatted for PI information": "No",
"Enclosure Device ID": "32",
"Enclosure position": "1",
"FDE Capable": "Not Capable",
"FDE Enable": "Disable",
"Firmware state": "Unconfigured(good), Spun Up",
"Foreign State": "None",
"Inquiry Data": "WD WD3001BKHG D1S6WXU1E13VTSK4",
"Last Predictive Failure Event Seq Number": "0",
"Link Speed": "6.0Gb/s",
"Locked": "Unlocked",
"Media Error Count": "0",
"Media Type": "Hard Disk Device",
"Needs EKM Attention": "No",
"Non Coerced Size": "278.896 GB [0x22dcb25c Sectors]",
"Other Error Count": "0",
"PD Type": "SAS",
"PI": "No PI",
"PI Eligibility": "No",
"Port status": "Active",
"Port's Linkspeed": "6.0Gb/s",
"Predictive Failure Count": "0",
"Raw Size": "279.396 GB [0x22ecb25c Sectors]",
"SAS Address(0)": "0x50000c0f02cc6ac6",
"SAS Address(1)": "0x0",
"Sector Size": "0",
"Secured": "Unsecured",
"Sequence Number": "3",
"Shield Counter": "0",
"Slot Number": "4",
"Successful diagnostics completion on": "N/A",
"WWN": "50000C0F02CC6AC5"
}
},
{
"ControllerID": "0",
"ControllerDriver": "megacli",
"VolumeID": "",
"Enclosure": "32",
"Size": 299439751168,
"UsedSize": 0,
"SectorCount": 584843264,
"PhysicalSectorSize": 0,
"LogicalSectorSize": 0,
"Slot": 5,
"Protocol": "sas",
"MediaType": "disk",
"Status": "Unconfigured(good), Spun Up",
"JBOD": false,
"Info": {
"Coerced Size": "278.875 GB [0x22dc0000 Sectors]",
"Connected Port Number": "7(path0)",
"Device Firmware Level": "D1S6",
"Device Id": "5",
"Device Speed": "6.0Gb/s",
"Drive has flagged a S.M.A.R.T alert": "No",
"Drive is formatted for PI information": "No",
"Enclosure Device ID": "32",
"Enclosure position": "1",
"FDE Capable": "Not Capable",
"FDE Enable": "Disable",
"Firmware state": "Unconfigured(good), Spun Up",
"Foreign State": "None",
"Inquiry Data": "WD WD3001BKHG D1S6WXU1E13VVSV5",
"Last Predictive Failure Event Seq Number": "0",
"Link Speed": "6.0Gb/s",
"Locked": "Unlocked",
"Media Error Count": "0",
"Media Type": "Hard Disk Device",
"Needs EKM Attention": "No",
"Non Coerced Size": "278.896 GB [0x22dcb25c Sectors]",
"Other Error Count": "0",
"PD Type": "SAS",
"PI": "No PI",
"PI Eligibility": "No",
"Port status": "Active",
"Port's Linkspeed": "6.0Gb/s",
"Predictive Failure Count": "0",
"Raw Size": "279.396 GB [0x22ecb25c Sectors]",
"SAS Address(0)": "0x50000c0f02197112",
"SAS Address(1)": "0x0",
"Sector Size": "0",
"Secured": "Unsecured",
"Sequence Number": "3",
"Shield Counter": "0",
"Slot Number": "5",
"Successful diagnostics completion on": "N/A",
"WWN": "50000C0F02197111"
}
},
{
"ControllerID": "0",
"ControllerDriver": "megacli",
"VolumeID": "",
"Enclosure": "32",
"Size": 299439751168,
"UsedSize": 0,
"SectorCount": 584843264,
"PhysicalSectorSize": 0,
"LogicalSectorSize": 0,
"Slot": 6,
"Protocol": "sas",
"MediaType": "disk",
"Status": "Unconfigured(good), Spun Up",
"JBOD": false,
"Info": {
"Coerced Size": "278.875 GB [0x22dc0000 Sectors]",
"Connected Port Number": "1(path0)",
"Device Firmware Level": "D1S6",
"Device Id": "6",
"Device Speed": "6.0Gb/s",
"Drive has flagged a S.M.A.R.T alert": "No",
"Drive is formatted for PI information": "No",
"Enclosure Device ID": "32",
"Enclosure position": "1",
"FDE Capable": "Not Capable",
"FDE Enable": "Disable",
"Firmware state": "Unconfigured(good), Spun Up",
"Foreign State": "None",
"Inquiry Data": "WD WD3001BKHG D1S6WXU1E13VTTV4",
"Last Predictive Failure Event Seq Number": "0",
"Link Speed": "6.0Gb/s",
"Locked": "Unlocked",
"Media Error Count": "0",
"Media Type": "Hard Disk Device",
"Needs EKM Attention": "No",
"Non Coerced Size": "278.896 GB [0x22dcb25c Sectors]",
"Other Error Count": "0",
"PD Type": "SAS",
"PI": "No PI",
"PI Eligibility": "No",
"Port status": "Active",
"Port's Linkspeed": "6.0Gb/s",
"Predictive Failure Count": "0",
"Raw Size": "279.396 GB [0x22ecb25c Sectors]",
"SAS Address(0)": "0x50000c0f02764fae",
"SAS Address(1)": "0x0",
"Sector Size": "0",
"Secured": "Unsecured",
"Sequence Number": "3",
"Shield Counter": "0",
"Slot Number": "6",
"Successful diagnostics completion on": "N/A",
"WWN": "50000C0F02764FAD"
}
},
{
"ControllerID": "0",
"ControllerDriver": "megacli",
"VolumeID": "",
"Enclosure": "32",
"Size": 299439751168,
"UsedSize": 0,
"SectorCount": 584843264,
"PhysicalSectorSize": 0,
"LogicalSectorSize": 0,
"Slot": 7,
"Protocol": "sas",
"MediaType": "disk",
"Status": "Unconfigured(good), Spun Up",
"JBOD": false,
"Info": {
"Coerced Size": "278.875 GB [0x22dc0000 Sectors]",
"Connected Port Number": "2(path0)",
"Device Firmware Level": "D1S6",
"Device Id": "7",
"Device Speed": "6.0Gb/s",
"Drive has flagged a S.M.A.R.T alert": "No",
"Drive is formatted for PI information": "No",
"Enclosure Device ID": "32",
"Enclosure position": "1",
"Exit Code": "0x00",
"FDE Capable": "Not Capable",
"FDE Enable": "Disable",
"Firmware state": "Unconfigured(good), Spun Up",
"Foreign State": "None",
"Inquiry Data": "WD WD3001BKHG D1S6WXU1E13VKVC8",
"Last Predictive Failure Event Seq Number": "0",
"Link Speed": "6.0Gb/s",
"Locked": "Unlocked",
"Media Error Count": "0",
"Media Type": "Hard Disk Device",
"Needs EKM Attention": "No",
"Non Coerced Size": "278.896 GB [0x22dcb25c Sectors]",
"Other Error Count": "0",
"PD Type": "SAS",
"PI": "No PI",
"PI Eligibility": "No",
"Port status": "Active",
"Port's Linkspeed": "6.0Gb/s",
"Predictive Failure Count": "0",
"Raw Size": "279.396 GB [0x22ecb25c Sectors]",
"SAS Address(0)": "0x50000c0f02766fba",
"SAS Address(1)": "0x0",
"Sector Size": "0",
"Secured": "Unsecured",
"Sequence Number": "3",
"Shield Counter": "0",
"Slot Number": "7",
"Successful diagnostics completion on": "N/A",
"WWN": "50000C0F02766FB9"
}
}
],
"Info": {
"Access Policy": "Yes",
"Alarm": "Absent",
"Alarm Control": "Yes",
"Alarm Disable": "No",
"Allow Boot with Preserved Cache": "No",
"Allow Ctrl Encryption": "No",
"Allow HDD SAS/SATA Mix in VD": "No",
"Allow HDD/SSD Mix in VD": "No",
"Allow Mix in Enclosure": "Yes",
"Allow Mixed Redundancy on Array": "No",
"Allow SATA in Cluster": "No",
"Allow SSD SAS/SATA Mix in VD": "No",
"Allowed Device Type": "SAS/SATA Mix",
"Any Offline VD Cache Preserved": "No",
"Auto Detect BackPlane Enable": "SGPIO/i2c SEP",
"Auto Detect BackPlane Enabled": "SGPIO/i2c SEP",
"Auto Enhanced Import": "No",
"Auto Rebuild": "Enabled",
"BBU": "Present",
"BGI Rate": "30%",
"BIOS Continue on Error": "0",
"BIOS Enumerate VDs": "Yes",
"BIOS Error Handling": "Stop On Errors",
"BIOS Version": "5.38.00_4.12.05.00_0x05260000",
"BOOT Version": "06.253.57.219",
"Background Rate": "30",
"Battery FRU": "N/A",
"Battery Warning": "Enabled",
"Block SSD Write Disk Cache Change": "No",
"Boot Block Version": "2.03.00.00-0004",
"BreakMirror RAID Support": "Yes",
"CC Rate": "Yes",
"Cache Flush Interval": "4s",
"Cache When BBU Bad": "Disabled",
"Cached IO": "No",
"Check Consistency Rate": "30%",
"ChipRevision": "D1",
"Cluster Active": "No",
"Cluster Disable": "Yes",
"Cluster Mode": "Disabled",
"Cluster Permitted": "No",
"Cluster Support": "No",
"Coercion Mode": "128MB",
"Controller Id": "0000",
"Controller temperature": "50 degree Celcius",
"Critical Disks": "0",
"Ctrl-R Version": "4.03-0002",
"Current Size of CacheCade": "0 GB",
"Current Size of FW Cache": "382 MB",
"Current Time": "10:15:48 1/26, 2021",
"Dedicated Hot Spare": "Yes",
"Default LD PowerSave Policy": "Controller Defined",
"Default spin down time in minutes": "30",
"Degraded": "0",
"Delay Among Spinup Groups": "12s",
"Delay during POST": "0",
"Deny CC": "No",
"Deny Clear": "Yes",
"Deny Force Failed": "No",
"Deny Force Good/Bad": "No",
"Deny Locate": "No",
"Deny Missing Replace": "No",
"Deny SCSI Passthrough": "No",
"Deny SMP Passthrough": "No",
"Deny STP Passthrough": "No",
"Device Id": "005b",
"Device Interface": "PCIE",
"Direct PD Mapping": "Yes",
"Dirty LED Shows Drive Activity": "No",
"Disable Copyback": "No",
"Disable Ctrl-R": "No",
"Disable Join Mirror": "Yes",
"Disable Online Controller Reset": "No",
"Disable Online PFK Change": "No",
"Disable Puncturing": "No",
"Disable Spin Down of hot spares": "Yes",
"Disk Cache Policy": "Yes",
"Disks": "8",
"ECC Bucket Count": "0",
"Ecc Bucket Leak Rate": "240 Minutes",
"Ecc Bucket Size": "255",
"Enable Copyback on SMART": "No",
"Enable Copyback to SSD on SMART Error": "No",
"Enable JBOD": "No",
"Enable LDBBM": "Yes",
"Enable Led Header": "No",
"Enable SSD Patrol Read": "No",
"Enable Shield State": "No",
"Enable Spin Down of UnConfigured Drives": "No",
"Enable Web BIOS": "No",
"EnableCrashDump": "No",
"EnableLDBBM": "Yes",
"Exit Code": "0x00",
"Expose Enclosure Devices": "Disabled",
"FW Package Build": "21.2.0-0007",
"FW Version": "3.130.05-2086",
"Failed Disks": "0",
"Flash": "Present",
"Flush Time": "4 seconds",
"Force Offline": "Yes",
"Force Online": "Yes",
"Force Rebuild": "Yes",
"Foreign Config Import": "Yes",
"Global Hot Spares": "Yes",
"Host Interface": "PCIE",
"Host Request Reordering": "Enabled",
"IO Policy": "Yes",
"Interrupt Throttle Active Count": "16",
"Interrupt Throttle Completion": "50us",
"LED Show Drive Activity": "Yes",
"Link Speed": "2",
"Load Balance Mode": "Auto",
"Maintain PD Fail History": "Disabled",
"Max Arms Per VD": "32",
"Max Arrays": "128",
"Max Chained Enclosures": "4",
"Max Configurable CacheCade Size": "512 GB",
"Max Data Transfer Size": "8192 sectors",
"Max Drives to Spinup at One Time": "4",
"Max LD per array": "16",
"Max Number of VDs": "64",
"Max Parallel Commands": "1008",
"Max SGE Count": "60",
"Max Spans Per VD": "8",
"Max Strip Size": "1.0 MB",
"Max Strips PerIO": "42",
"Maximum number of direct attached drives to spin up in 1 min": "20",
"Memory": "Present",
"Memory Correctable Errors": "0",
"Memory Size": "512MB",
"Memory Uncorrectable Errors": "0",
"Mfg. Date": "09/08/13",
"Min Strip Size": "64 KB",
"NVDATA Version": "2.1108.03-0095",
"NVRAM": "Present",
"Number of Backend Port": "8",
"Number of Frontend Port": "0",
"Offline": "0",
"On board Expander": "Absent",
"PFK in NVRAM": "No",
"POST delay": "90 seconds",
"PR Correct Unconfigured Areas": "Yes",
"PR Rate": "30%",
"Patrol Read Rate": "Yes",
"Phy Polarity": "0",
"Phy PolaritySplit": "0",
"Physical Devices": "9",
"Physical Drive Coercion Mode": "128MB",
"Power Saving option": "Don't spin down unconfigured drives",
"Power Savings": "Yes",
"PreBoot CLI Enabled": "No",
"Preboot CLI Version": "05.00-03:#%00008",
"Predictive Fail Poll Interval": "300sec",
"Product Name": "PERC H710 Mini",
"RAID Level Supported": "RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span",
"ROC temperature": "50 degree Celsius",
"Read Policy": "Yes",
"Rebuild Rate": "30%",
"Reconstruct Rate": "Yes",
"Reconstruction": "Yes",
"Reconstruction Rate": "30%",
"Restore Hot Spare on Insertion": "No",
"Restore HotSpare on Insertion": "Disabled",
"Revertible Hot Spares": "Yes",
"Revision No": "A03",
"Rework Date": "09/08/13",
"SAS Address": "5b8ca3a0f99e5100",
"SAS Disable": "No",
"SMART Mode": "Mode 6",
"Security Key Assigned": "No",
"Security Key Failed": "No",
"Security Key Not Backedup": "No",
"Self Diagnostic": "Yes",
"Serial Debugger": "Present",
"Serial No": "39704H0",
"Snapshot Enabled": "No",
"Spanning": "Yes",
"Spin Down Mode": "None",
"Spin Down time": "30",
"Strip Size": "64kB",
"SubDeviceId": "1f38",
"SubVendorId": "1028",
"Support Boot Time PFK Change": "No",
"Support Breakmirror": "Yes",
"Support PFK": "No",
"Support PI": "No",
"Support Security": "Yes",
"Support Shield State": "No",
"Support Temperature": "Yes",
"Support the OCE without adding drives": "Yes",
"Supported Drives": "SAS, SATA",
"T10 Power State": "Yes",
"TPM": "Absent",
"TTY Log In Flash": "No",
"Temperature sensor for ROC": "Present",
"Temperature sensor for controller": "Present",
"Time taken to detect CME": "60s",
"Treat Single span R1E as R10": "Yes",
"Un-Certified Hard Disk Drives": "Allow",
"Upgrade Key": "Absent",
"Use FDE Only": "Yes",
"Use disk activity for locate": "No",
"Vendor Id": "1000",
"Virtual Drives": "0",
"Write Policy": "Yes",
"ZCR Config": "Unknown",
"Zero Based Enclosure Enumeration": "Yes"
}
}
]