diff --git a/device_files/install/k1mod_init.sh b/device_files/install/k1mod_init.sh
index 61237a2..4872f6b 100755
--- a/device_files/install/k1mod_init.sh
+++ b/device_files/install/k1mod_init.sh
@@ -74,6 +74,45 @@ do_setup()
     xz -dc $WORK_DIR/chroot.tar.xz | tar -xf - -C $CHROOT_DIR
     sync
 
+    ##############################
+    # which k1 are you?
+    ##############################
+
+    PRINTER_CONF_DIR="${CHROOT_DIR}//root/printer_data/config"
+    machine_info=$(tr -d '\0' </dev/mmcblk0p2)
+    if [[ $machine_info == *"CR-K1;CR4CU220812S12;;;;;"* ]]; then
+	echo "Identified machine as K1. Configuring printer.cfg for a K1."
+	cp $PRINTER_CONF_DIR/k1/*.cfg $PRINTER_CONF_DIR/
+	rm $PRINTER_CONF_DIR/printer_k1c.cfg $PRINTER_CONF_DIR/printer_variant1.cfg
+
+    elif [[ $machine_info == *"CR-K1;CR4CU220812S12;;;1;;"* ]]; then
+	echo "Identified machine as K1 New Variant. Configuring printer.cfg for a K1 New Variant."
+	cp $PRINTER_CONF_DIR/k1/*.cfg $PRINTER_CONF_DIR/
+	mv $PRINTER_CONF_DIR/printer_variant1.cfg $PRINTER_CONF_DIR/printer.cfg
+	rm $PRINTER_CONF_DIR/printer_k1c.cfg
+
+    elif [[ $machine_info == *"CR-K1 Max;CR4CU220812S12;;;;;"* ]]; then
+	echo "Identified machine as K1 Max. Configuring printer.cfg for a K1 Max."
+	cp $PRINTER_CONF_DIR/k1max/*.cfg $PRINTER_CONF_DIR/
+	rm $PRINTER_CONF_DIR/printer_variant1.cfg
+
+    elif [[ $machine_info == *"CR-K1 Max;CR4CU220812S12;;;1;;"* ]]; then
+	echo "Identified machine as K1 Max New Variant. Configuring printer.cfg for a K1 Max New Variant."
+	cp $PRINTER_CONF_DIR/k1max/*.cfg $PRINTER_CONF_DIR/
+	mv $PRINTER_CONF_DIR/printer_variant1.cfg  $PRINTER_CONF_DIR/printer.cfg
+
+    elif [[ $machine_info == *"K1C;CR4CU220812S12;;;;;"* ]]; then
+	echo "Identified machine as K1C. Configuring printer.cfg for a K1C."
+	cp $PRINTER_CONF_DIR/k1/*.cfg $PRINTER_CONF_DIR/
+	mv $PRINTER_CONF_DIR/printer_k1c.cfg $PRINTER_CONF_DIR/printer.cfg
+	rm $PRINTER_CONF_DIR/printer_variant1.cfg
+
+    else
+	echo "Failed to idenity K1 model. Exiting.."
+	exit 1
+    fi
+
+
     # do intial setup
     $CHROOT_DIR/etc/init/S00klipper_mod setup
     sync
diff --git a/printer_configs/custom_gcode.cfg b/printer_configs/custom_gcode.cfg
index 4376933..ea8359d 100644
--- a/printer_configs/custom_gcode.cfg
+++ b/printer_configs/custom_gcode.cfg
@@ -1,15 +1,8 @@
-[gcode_macro _CLIENT_VARIABLE]
-variable_use_custom_pos  : True
-variable_custom_park_x   : 5
-variable_custom_park_y   : 10
-variable_custom_park_dz   : 50.0 ; custom dz value; the value in mm to lift the nozzle when move to park position
-variable_park_at_cancel   : True
-gcode:
-
 [gcode_macro START_PRINT]
 gcode:
     {% set BED_TEMP=params.BED_TEMP|default(55)|float %}
     {% set EXTRUDER_TEMP=params.EXTRUDER_TEMP|default(195)|float %}
+    {% set eddy = ('probe_eddy_current btt_eddy' in printer.configfile.settings) %}
     
     # Home the printer
     G28
@@ -18,15 +11,16 @@ gcode:
     M140 S{BED_TEMP}
     M190 S{BED_TEMP}
 
-    SET_VELOCITY_LIMIT ACCEL=15000 ACCEL_TO_DECEL=10000 SQUARE_CORNER_VELOCITY=25   # drop accels to prevent hyper agressive meshing
     BED_MESH_CLEAR
+    {% if eddy %}
     BED_MESH_CALIBRATE METHOD=rapid_scan ADAPTIVE=1 ADAPTIVE_MARGIN=5
-
+    {% else %}
+    BED_MESH_CALIBRATE ADAPTIVE=1 ADAPTIVE_MARGIN=5
+    {% endif %}
     # Heat the extruder to the desired temperature
     M104 S{EXTRUDER_TEMP}
 
     SMART_PARK                                                                      # park the printhead near the print area
-    SET_VELOCITY_LIMIT ACCEL=18000 ACCEL_TO_DECEL=10000 SQUARE_CORNER_VELOCITY=5    # up acceleration back to slightly below regular travel speeds
     M109 S{EXTRUDER_TEMP}                                                           # wait for nozzle temperature before next step
     LINE_PURGE 
 
diff --git a/printer_configs/bltouch.cfg b/printer_configs/k1/bltouch.cfg
similarity index 81%
rename from printer_configs/bltouch.cfg
rename to printer_configs/k1/bltouch.cfg
index eb3434d..889b712 100644
--- a/printer_configs/bltouch.cfg
+++ b/printer_configs/k1/bltouch.cfg
@@ -42,3 +42,11 @@ screw4_name: rear left screw
 speed: 100
 horizontal_move_z: 5
 screw_thread: CW-M4
+
+[gcode_macro _CLIENT_VARIABLE]
+variable_use_custom_pos  : True
+variable_custom_park_x   : 205
+variable_custom_park_y   : 204
+variable_custom_park_dz   : 50.0
+variable_park_at_cancel   : True
+gcode:
diff --git a/printer_configs/btteddy.cfg b/printer_configs/k1/btteddy.cfg
similarity index 56%
rename from printer_configs/btteddy.cfg
rename to printer_configs/k1/btteddy.cfg
index b5f36fa..d630867 100644
--- a/printer_configs/btteddy.cfg
+++ b/printer_configs/k1/btteddy.cfg
@@ -1,6 +1,11 @@
+#
+# This btt eddy configuration is for this mount:
+# https://makerworld.com/en/models/494931
+#
+
 ### btt eddy
 [mcu eddy]
-serial: /dev/serial/by-id/usb-Klipper_rp2040_45503571288CBAF8-if00
+serial: /dev/serial/by-id/usb-Klipper_rp2040_45503571288CBAF8-if00 # change this based on your device path
 
 [temperature_sensor btt_eddy_mcu]
 sensor_type: temperature_mcu
@@ -20,7 +25,15 @@ y_offset: 11.8 # Set according to the actual offset relative to the nozzle
 [bed_mesh]
 horizontal_move_z: 2
 speed: 300
-mesh_min: 0, 20
+mesh_min: 5, 30
 mesh_max: 185, 215
 probe_count: 20, 20
 algorithm: bicubic
+
+[gcode_macro _CLIENT_VARIABLE]
+variable_use_custom_pos  : True
+variable_custom_park_x   : 5
+variable_custom_park_y   : 10
+variable_custom_park_dz   : 50.0 ; custom dz value; the value in mm to lift the nozzle when move to park position
+variable_park_at_cancel   : True
+gcode:
diff --git a/printer_configs/microprobe.cfg b/printer_configs/k1/microprobe.cfg
similarity index 59%
rename from printer_configs/microprobe.cfg
rename to printer_configs/k1/microprobe.cfg
index 68ae793..06cbf9a 100644
--- a/printer_configs/microprobe.cfg
+++ b/printer_configs/k1/microprobe.cfg
@@ -11,7 +11,8 @@ gcode:
   SET_PIN PIN=probe_enable VALUE=0
 
 [probe]
-pin: ^!nozzle_mcu: PA9
+#pin: ^nozzle_mcu: PA9  # MicroProbe V1 users should use this line to trigger on high
+pin: ^!nozzle_mcu: PA9  # MicroProbe V2 users should use this line to trigger on low
 deactivate_on_each_sample: False
 x_offset: -33.0
 y_offset: 0
@@ -26,30 +27,6 @@ activate_gcode:
 deactivate_gcode:
   PROBE_UP
 
-[bed_mesh]
-speed: 150
-mesh_min: 0,3
-mesh_max: 196,215
-probe_count: 12,12
-fade_start: 3.0
-fade_end: 10.0
-horizontal_move_z: 8
-algorithm: bicubic
-bicubic_tension: 0.1
-
-[screws_tilt_adjust]
-screw1: 59,20
-screw1_name: front left screw
-screw2: 229,20
-screw2_name: front right screw
-screw3: 229,190
-screw3_name: rear right screw
-screw4: 59,190
-screw4_name: rear left screw
-speed: 100
-horizontal_move_z: 5
-screw_thread: CW-M4
-
 #
 # This configuration is for the K1 and K1C only
 #
@@ -68,14 +45,22 @@ algorithm: bicubic
 bicubic_tension: 0.1
 
 [screws_tilt_adjust]
-screw1: 59,20
-screw1_name: front left screw
-screw2: 229,20
-screw2_name: front right screw
-screw3: 229,190
-screw3_name: rear right screw
-screw4: 59,190
-screw4_name: rear left screw
+screw1: 58,20
+screw1_name: front left
+screw2: 228,20
+screw2_name: front right
+screw3: 228,190
+screw3_name: rear right
+screw4: 58,190
+screw4_name: rear left
 speed: 100
 horizontal_move_z: 5
 screw_thread: CW-M4
+
+[gcode_macro _CLIENT_VARIABLE]
+variable_use_custom_pos  : True
+variable_custom_park_x   : 185
+variable_custom_park_y   : 210
+variable_custom_park_dz   : 50.0
+variable_park_at_cancel   : True
+gcode:
diff --git a/printer_configs/printer.cfg b/printer_configs/k1/printer.cfg
similarity index 100%
rename from printer_configs/printer.cfg
rename to printer_configs/k1/printer.cfg
diff --git a/printer_configs/k1/printer_k1c.cfg b/printer_configs/k1/printer_k1c.cfg
new file mode 100644
index 0000000..7ca3838
--- /dev/null
+++ b/printer_configs/k1/printer_k1c.cfg
@@ -0,0 +1,273 @@
+# K1C
+# Printer_size: 220x220x250
+# Version: v2.0.5
+# CreateDate: 2023/09/05
+# Nozzle_mcu: chip: GD32F303CBT6
+#             version: CR-K1-MAX-NOZZLE-V1.2.0
+# Leveling_mcu: chip: GD32E230F8P6
+#             version: CR-K1-MAX-LEVELING-V1.1.0
+# mcu: chip: GD32F303RET6
+#      version: CR4CU220812S12
+
+[include GuppyScreen/*.cfg]
+[include KAMP/KAMP_Settings.cfg]
+[include sensorless.cfg]
+[include custom_gcode.cfg]
+
+### start probe
+### select and configure one probe, comment the rest
+
+[include btteddy.cfg]
+#[include bltouch.cfg]       ## uncomment if using bltouch
+#[include microprobe.cfg]    ## uncomment if using microprobe
+
+## end probe
+
+[include fluidd.cfg]
+[include fan_control.cfg]
+[include timelapse.cfg]
+
+[mcu]
+serial: /dev/ttyS7
+baud: 230400
+restart_method: command
+
+[mcu nozzle_mcu]
+serial: /dev/ttyS1
+baud: 230400
+restart_method: command
+
+# [mcu leveling_mcu]
+# serial: /dev/ttyS9
+# baud: 230400
+# restart_method: command
+
+[verify_heater extruder]
+[verify_heater heater_bed]
+check_gain_time: 120
+heating_gain: 1.0
+hysteresis: 10
+
+[mcu rpi]
+serial: /tmp/klipper_host_mcu
+
+[idle_timeout]
+timeout: 99999999
+
+[virtual_sdcard]
+path: /root/printer_data/gcodes
+
+[gcode_arcs]
+resolution: 1.0
+
+[temperature_sensor mcu_temp]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[temperature_sensor chamber_temp]
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+min_temp: 0
+max_temp: 125
+
+[temperature_fan _chamber_fan]
+pin: PC0
+cycle_time: 0.0100
+hardware_pwm: false
+max_power: 1
+shutdown_speed: 0
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+min_temp: 0
+max_temp: 70
+control: watermark
+max_delta: 2
+target_temp: 35.0
+max_speed: 1.0
+min_speed: 0.0
+
+[stepper_x]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+microsteps: 32
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_x:virtual_endstop
+position_endstop: 229
+position_min: -5
+position_max: 229
+homing_speed: 30
+homing_retract_dist:0
+
+[tmc2209 stepper_x]
+uart_pin:PA9
+interpolate: True
+run_current:1.5
+hold_current:1.0
+sense_resistor: 0.100
+stealthchop_threshold: 0
+uart_address:3
+diag_pin: ^PB12
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 1
+# driver_TOFF: 1
+# driver_HEND: 0
+# driver_HSTRT: 7
+driver_SGTHRS: 75
+
+[stepper_y]
+step_pin: PB8
+dir_pin: !PB7
+enable_pin: !PC3
+microsteps: 32
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_y:virtual_endstop
+position_endstop: -0.5
+position_min: -0.5
+position_max: 227
+homing_speed: 30
+homing_retract_dist:0
+
+[tmc2209 stepper_y]
+uart_pin:PA10
+interpolate: True
+run_current:1.5
+hold_current:1.0
+sense_resistor: 0.100
+stealthchop_threshold: 0
+uart_address:3
+diag_pin: ^PB13
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 1
+# driver_TOFF: 1
+# driver_HEND: 0
+# driver_HSTRT: 7
+driver_SGTHRS: 75
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance:8
+gear_ratio: 64:20
+endstop_pin: probe:z_virtual_endstop
+position_max: 255
+position_min: -10
+
+[tmc2209 stepper_z]
+uart_pin: PA11
+uart_address: 3
+run_current: 0.8
+diag_pin: ^PB14
+stealthchop_threshold: 0
+sense_resistor: 0.100
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 1
+# driver_TOFF: 1
+# driver_HEND: 2
+# driver_HSTRT: 2
+driver_SGTHRS: 0
+
+[extruder]
+max_extrude_only_distance: 1000.0
+max_extrude_cross_section: 80
+step_pin: nozzle_mcu:PB1
+dir_pin: nozzle_mcu:PB0
+enable_pin: !nozzle_mcu:PB2
+microsteps: 16
+rotation_distance: 6.9
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: nozzle_mcu:PB7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: nozzle_mcu:PA0
+pressure_advance: 0.04
+pressure_advance_smooth_time: 0.040
+control: pid
+pid_Kp: 25.013
+pid_Ki: 2.566
+pid_Kd: 60.966
+min_temp: 0
+max_temp: 320
+
+[tmc2209 extruder]
+uart_pin: nozzle_mcu:PB11
+tx_pin: nozzle_mcu:PB10
+
+uart_address: 3
+run_current: 0.55
+sense_resistor: 0.150
+stealthchop_threshold: 0
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 2
+# driver_TOFF: 3
+# driver_HEND: 0
+# driver_HSTRT: 5
+
+[heater_bed]
+heater_pin: PB10
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: watermark
+# control: pid
+# pid_kp: 27
+# pid_ki: 0.08
+# pid_kd: 0
+min_temp: 0
+max_temp: 115
+
+[filament_switch_sensor filament_sensor]
+pause_on_runout: true
+switch_pin: !PC15
+runout_gcode:
+  {% if printer.extruder.can_extrude|lower == 'true' %}
+    G91
+    G0 E30 F600
+    G90
+  {% endif %}
+
+[static_digital_output my_fan_output_pins]
+pins: nozzle_mcu: PB6
+
+[output_pin LED]
+pin:PB0
+pwm: True
+cycle_time: 0.010
+value: 1
+
+[adxl345]
+cs_pin: nozzle_mcu:PA4
+spi_speed: 5000000
+axes_map: x,-z,y
+spi_software_sclk_pin: nozzle_mcu:PA5
+spi_software_mosi_pin: nozzle_mcu:PA7
+spi_software_miso_pin: nozzle_mcu:PA6
+
+[resonance_tester]
+accel_chip: adxl345
+accel_per_hz: 75
+# min_freq: 30
+# max_freq: 100
+probe_points:
+   110,110,10
+
+[display_status]
+
+[printer]
+kinematics: corexy
+max_velocity: 600
+max_accel: 20000
+max_z_velocity: 10
+square_corner_velocity: 5.0
+max_z_accel: 300
+
+[pause_resume]
+# recover_velocity: 500.
+
+[exclude_object]
diff --git a/printer_configs/k1/printer_variant1.cfg b/printer_configs/k1/printer_variant1.cfg
new file mode 100644
index 0000000..2d7d153
--- /dev/null
+++ b/printer_configs/k1/printer_variant1.cfg
@@ -0,0 +1,272 @@
+# K1
+# Printer_size: 220x220x250
+# Version: v1.0.1
+# CreateDate: 2024/03/07
+# Nozzle_mcu: chip: GD32F303CBT6
+#             version: CR-K1-MAX-NOZZLE-V1.2.0
+# Leveling_mcu: chip: GD32E230F8P6
+#             version: CR-K1-MAX-LEVELING-V1.1.0
+# mcu: chip: GD32F303RET6
+#      version: CR4CU220812S12
+
+[include GuppyScreen/*.cfg]
+[include KAMP/KAMP_Settings.cfg]
+[include sensorless.cfg]
+[include custom_gcode.cfg]
+
+### start probe
+### select and configure one probe, comment the rest
+
+[include btteddy.cfg]
+#[include bltouch.cfg]       ## uncomment if using bltouch
+#[include microprobe.cfg]    ## uncomment if using microprobe
+
+## end probe
+
+[include fluidd.cfg]
+[include fan_control.cfg]
+[include timelapse.cfg]
+
+[mcu]
+serial: /dev/ttyS7
+baud: 230400
+restart_method: command
+
+[mcu nozzle_mcu]
+serial: /dev/ttyS1
+baud: 230400
+restart_method: command
+
+# [mcu leveling_mcu]
+# serial: /dev/ttyS9
+# baud: 230400
+# restart_method: command
+
+[verify_heater extruder]
+[verify_heater heater_bed]
+check_gain_time: 120
+heating_gain: 1.0
+hysteresis: 10
+
+[mcu rpi]
+serial: /tmp/klipper_host_mcu
+
+[idle_timeout]
+timeout: 99999999
+
+[virtual_sdcard]
+path: /root/printer_data/gcodes
+
+[gcode_arcs]
+resolution: 1.0
+
+[temperature_sensor mcu_temp]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[temperature_sensor chamber_temp]
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+min_temp: 0
+max_temp: 125
+
+[temperature_fan _chamber_fan]
+pin: PC0
+cycle_time: 0.0100
+hardware_pwm: false
+max_power: 1
+shutdown_speed: 0
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+min_temp: 0
+max_temp: 70
+control: watermark
+max_delta: 2
+target_temp: 35.0
+max_speed: 1.0
+min_speed: 0.0
+
+[stepper_x]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+microsteps: 32
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_x:virtual_endstop
+position_endstop: 229
+position_min: -5
+position_max: 229
+homing_speed: 30
+homing_retract_dist:0
+
+[tmc2209 stepper_x]
+uart_pin:PA9
+interpolate: True
+run_current:1.5
+hold_current:1.0
+sense_resistor: 0.100
+stealthchop_threshold: 0
+uart_address:3
+diag_pin: ^PB12
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+driver_TBL: 0
+driver_TOFF: 1
+driver_HEND: 0
+driver_HSTRT: 0
+driver_SGTHRS: 75
+
+[stepper_y]
+step_pin: PB8
+dir_pin: !PB7
+enable_pin: !PC3
+microsteps: 32
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_y:virtual_endstop
+position_endstop: -0.5
+position_min: -0.5
+position_max: 226
+homing_speed: 30
+homing_retract_dist:0
+
+[tmc2209 stepper_y]
+uart_pin:PA10
+interpolate: True
+run_current:1.5
+hold_current:1.0
+sense_resistor: 0.100
+stealthchop_threshold: 0
+uart_address:3
+diag_pin: ^PB13
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+driver_TBL: 0
+driver_TOFF: 1
+driver_HEND: 0
+driver_HSTRT: 0
+driver_SGTHRS: 75
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance:8
+gear_ratio: 64:20
+endstop_pin: probe:z_virtual_endstop
+position_max: 255
+position_min: -10
+
+[tmc2209 stepper_z]
+uart_pin: PA11
+uart_address: 3
+run_current: 0.8
+diag_pin: ^PB14
+stealthchop_threshold: 0
+sense_resistor: 0.100
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 1
+# driver_TOFF: 1
+# driver_HEND: 2
+# driver_HSTRT: 2
+driver_SGTHRS: 0
+
+[extruder]
+max_extrude_only_distance: 1000.0
+max_extrude_cross_section: 80
+step_pin: nozzle_mcu:PB1
+dir_pin: nozzle_mcu:PB0
+enable_pin: !nozzle_mcu:PB2
+microsteps: 16
+rotation_distance: 6.9
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: nozzle_mcu:PB7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: nozzle_mcu:PA0
+pressure_advance: 0.04
+pressure_advance_smooth_time: 0.040
+control: pid
+pid_Kp: 25.013
+pid_Ki: 2.566
+pid_Kd: 60.966
+min_temp: 0
+max_temp: 320
+
+[tmc2209 extruder]
+uart_pin: nozzle_mcu:PB11
+tx_pin: nozzle_mcu:PB10
+uart_address: 3
+run_current: 0.55
+sense_resistor: 0.150
+stealthchop_threshold: 0
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 2
+# driver_TOFF: 3
+# driver_HEND: 0
+# driver_HSTRT: 5
+
+[heater_bed]
+heater_pin: PB10
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: watermark
+# control: pid
+# pid_kp: 27
+# pid_ki: 0.08
+# pid_kd: 0
+min_temp: 0
+max_temp: 115
+
+[filament_switch_sensor filament_sensor]
+pause_on_runout: true
+switch_pin: !PC15
+runout_gcode:
+  {% if printer.extruder.can_extrude|lower == 'true' %}
+    G91
+    G0 E30 F600
+    G90
+  {% endif %}
+
+[static_digital_output my_fan_output_pins]
+pins: nozzle_mcu: PB6
+
+[output_pin LED]
+pin:PB0
+pwm: True
+cycle_time: 0.010
+value: 1
+
+[adxl345]
+cs_pin: nozzle_mcu:PA4
+spi_speed: 5000000
+axes_map: x,-z,y
+spi_software_sclk_pin: nozzle_mcu:PA5
+spi_software_mosi_pin: nozzle_mcu:PA7
+spi_software_miso_pin: nozzle_mcu:PA6
+
+[resonance_tester]
+accel_chip: adxl345
+accel_per_hz: 75
+# min_freq: 30
+# max_freq: 100
+probe_points:
+   110,110,10
+
+[display_status]
+
+[printer]
+kinematics: corexy
+max_velocity: 800
+max_accel: 20000
+max_z_velocity: 20
+square_corner_velocity: 5.0
+max_z_accel: 300
+
+[pause_resume]
+# recover_velocity: 500.
+
+[exclude_object]
diff --git a/printer_configs/k1max/bltouch.cfg b/printer_configs/k1max/bltouch.cfg
new file mode 100644
index 0000000..7abb0e3
--- /dev/null
+++ b/printer_configs/k1max/bltouch.cfg
@@ -0,0 +1,52 @@
+[bltouch]
+sensor_pin: ^nozzle_mcu: PA9
+control_pin: nozzle_mcu: PA8
+pin_move_time: 0.500
+x_offset: 0.0
+y_offset: 25.25 
+z_offset: 1.925
+speed: 1
+lift_speed: 20
+samples: 3
+probe_with_touch_mode: true
+samples_result: average
+stow_on_each_sample: false
+samples_tolerance: 0.1
+samples_tolerance_retries: 5
+sample_retract_dist: 3
+#
+# This configuration is for the K1 Max
+#
+# This microprobe configuration is for this mount:
+# https://www.printables.com/model/666186-creality-k1-bltouch-adapter
+#
+
+[bed_mesh]
+speed: 100
+horizontal_move_z: 8
+mesh_min: 5,30
+mesh_max: 285,280
+probe_count: 12,12
+algorithm: bicubic
+bicubic_tension: 0.1
+
+[screws_tilt_adjust]
+screw1: 19,-2
+screw1_name: front left
+screw2: 278,-2
+screw2_name: front right
+screw3: 248,247
+screw3_name: rear right
+screw4: 48,247
+screw4_name: rear left
+horizontal_move_z: 5
+speed: 150
+screw_thread: CW-M4
+
+[gcode_macro _CLIENT_VARIABLE]
+variable_use_custom_pos  : True 
+variable_custom_park_x   : 280
+variable_custom_park_y   : 275
+variable_custom_park_dz   : 50.0
+variable_park_at_cancel   : True 
+gcode:
diff --git a/printer_configs/k1max/btteddy.cfg b/printer_configs/k1max/btteddy.cfg
new file mode 100644
index 0000000..efb8802
--- /dev/null
+++ b/printer_configs/k1max/btteddy.cfg
@@ -0,0 +1,39 @@
+#
+# This btt eddy configuration is for this mount:
+# https://makerworld.com/en/models/494931
+#
+
+### btt eddy
+[mcu eddy]
+serial: /dev/serial/by-id/usb-Klipper_rp2040_45503571288CBAF8-if00 # change this based on your device path
+
+[temperature_sensor btt_eddy_mcu]
+sensor_type: temperature_mcu
+sensor_mcu: eddy
+min_temp: 10
+max_temp: 100
+
+[probe_eddy_current btt_eddy]
+sensor_type: ldc1612
+z_offset: 1.0
+#i2c_address:
+i2c_mcu: eddy
+i2c_bus: i2c0f
+x_offset: -38.5 # Set according to the actual offset relative to the nozzle
+y_offset: 11.8 # Set according to the actual offset relative to the nozzle
+
+[bed_mesh]
+horizontal_move_z: 2
+speed: 300
+mesh_min: 5, 30
+mesh_max: 262, 295
+probe_count: 40, 40
+algorithm: bicubic
+
+[gcode_macro _CLIENT_VARIABLE]
+variable_use_custom_pos  : True
+variable_custom_park_x   : 5
+variable_custom_park_y   : 10
+variable_custom_park_dz   : 50.0 ; custom dz value; the value in mm to lift the nozzle when move to park position
+variable_park_at_cancel   : True
+gcode:
diff --git a/printer_configs/k1max/microprobe.cfg b/printer_configs/k1max/microprobe.cfg
new file mode 100644
index 0000000..439e2b0
--- /dev/null
+++ b/printer_configs/k1max/microprobe.cfg
@@ -0,0 +1,66 @@
+[output_pin probe_enable]
+pin: nozzle_mcu: PA8 # Set to the control pin on your board
+value: 0
+
+[gcode_macro PROBE_DOWN]
+gcode:
+  SET_PIN PIN=probe_enable VALUE=1
+
+[gcode_macro PROBE_UP]
+gcode:
+  SET_PIN PIN=probe_enable VALUE=0
+
+[probe]
+#pin: ^nozzle_mcu: PA9  # MicroProbe V1 users should use this line to trigger on high
+pin: ^!nozzle_mcu: PA9  # MicroProbe V2 users should use this line to trigger on low
+deactivate_on_each_sample: False
+x_offset: -33.0
+y_offset: 0
+# this should be overriden but best to have a default
+z_offset = 0.500
+samples: 3
+samples_tolerance: 0.05
+samples_tolerance_retries: 3
+activate_gcode:
+  PROBE_DOWN
+  G4 P500
+deactivate_gcode:
+  PROBE_UP
+
+#
+# This configuration is for the K1 Max only
+#
+# This microprobe configuration is for this mount:
+# https://www.printables.com/model/867527-k1-biqu-microprobe-mount-remix
+#
+[bed_mesh]
+speed: 100
+horizontal_move_z: 8
+mesh_min: 5,5
+mesh_max: 262,295
+probe_count: 12,12
+fade_start: 1.0
+fade_end: 10.0
+algorithm: bicubic
+bicubic_tension: 0.1
+
+[screws_tilt_adjust]
+screw1: 54,21
+screw1_name: front left
+screw2: 312,21
+screw2_name: front right
+screw3: 283,270
+screw3_name: rear right
+screw4: 81,270
+screw4_name: rear left
+speed: 150
+horizontal_move_z: 5
+screw_thread: CW-M4
+
+[gcode_macro _CLIENT_VARIABLE]
+variable_use_custom_pos  : True 
+variable_custom_park_x   : 255
+variable_custom_park_y   : 290
+variable_custom_park_dz   : 50.0
+variable_park_at_cancel   : True 
+gcode:
diff --git a/printer_configs/k1max/printer.cfg b/printer_configs/k1max/printer.cfg
new file mode 100644
index 0000000..057a235
--- /dev/null
+++ b/printer_configs/k1max/printer.cfg
@@ -0,0 +1,278 @@
+# K1-MAX
+# Printer_size: 300x300x300
+# Version: v1.0.30
+# CreateDate: 2023/03/21
+# Nozzle_mcu: chip: GD32F303CBT6
+#             version: K1-NOZZLE-M_V12
+# Leveling_mcu: chip: GD32E230F8P6
+#             version: K1-MAX-L-V11
+# mcu: chip: GD32F303RET6
+#      version: CR4CU220812S12
+
+[include GuppyScreen/*.cfg]
+[include KAMP/KAMP_Settings.cfg]
+[include sensorless.cfg]
+[include custom_gcode.cfg]
+
+### start probe
+### select and configure one probe, comment the rest
+
+[include btteddy.cfg]
+#[include bltouch.cfg]       ## uncomment if using bltouch
+#[include microprobe.cfg]    ## uncomment if using microprobe
+
+## end probe
+
+[include fluidd.cfg]
+[include fan_control.cfg]
+[include timelapse.cfg]
+
+[mcu]
+serial: /dev/ttyS7
+baud: 230400
+restart_method: command
+
+[mcu nozzle_mcu]
+serial: /dev/ttyS1
+baud: 230400
+restart_method: command
+
+# [mcu leveling_mcu]
+# serial: /dev/ttyS9
+# baud: 230400
+# restart_method: command
+
+[verify_heater extruder]
+[verify_heater heater_bed]
+check_gain_time: 120
+heating_gain: 1.0
+hysteresis: 10
+
+[mcu rpi]
+serial: /tmp/klipper_host_mcu
+
+[idle_timeout]
+timeout: 99999999
+
+[virtual_sdcard]
+path: /root/printer_data/gcodes
+
+[gcode_arcs]
+resolution: 1.0
+
+[temperature_sensor mcu_temp]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[temperature_sensor chamber_temp]
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+min_temp: 0
+max_temp: 125
+
+[temperature_fan _chamber_fan]
+pin: PC0
+cycle_time: 0.0100
+hardware_pwm: false
+max_power: 1
+shutdown_speed: 0
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+min_temp: 0
+max_temp: 70
+control: watermark
+max_delta: 2
+target_temp: 35.0
+max_speed: 1.0
+min_speed: 0.0
+
+[stepper_x]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+microsteps: 32
+rotation_distance: 72
+endstop_pin: tmc2209_stepper_x:virtual_endstop
+position_endstop: 306.5
+position_min: -2
+position_max: 306.5
+homing_speed: 36
+homing_retract_dist:0
+
+[tmc2209 stepper_x]
+uart_pin:PA9
+interpolate: True
+run_current:1.5
+hold_current:1.0
+sense_resistor: 0.100
+stealthchop_threshold: 0
+uart_address:3
+diag_pin: ^PB12
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 1
+# driver_TOFF: 1
+# driver_HEND: 0
+# driver_HSTRT: 7
+driver_SGTHRS: 65
+
+[stepper_y]
+step_pin: PB8
+dir_pin: !PB7
+enable_pin: !PC3
+microsteps: 32
+rotation_distance: 72
+endstop_pin: tmc2209_stepper_y:virtual_endstop
+position_endstop: -2
+position_min: -2
+position_max: 306
+homing_speed: 36
+homing_retract_dist:0
+
+[tmc2209 stepper_y]
+uart_pin:PA10
+interpolate: True
+run_current:1.5
+hold_current:1.0
+sense_resistor: 0.100
+stealthchop_threshold: 0
+uart_address:3
+diag_pin: ^PB13
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 1
+# driver_TOFF: 1
+# driver_HEND: 0
+# driver_HSTRT: 7
+driver_SGTHRS: 65
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance:8
+gear_ratio: 64:20
+endstop_pin: probe:z_virtual_endstop
+position_max: 305
+position_min: -10
+homing_speed: 10
+second_homing_speed: 1
+homing_retract_dist: 2.0
+
+[tmc2209 stepper_z]
+uart_pin: PA11
+uart_address: 3
+run_current: 0.8
+diag_pin: ^PB14
+stealthchop_threshold: 0
+sense_resistor: 0.100
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 1
+# driver_TOFF: 1
+# driver_HEND: 2
+# driver_HSTRT: 2
+driver_SGTHRS: 0
+
+[extruder]
+max_extrude_only_distance: 1000.0
+max_extrude_cross_section: 80
+step_pin: nozzle_mcu:PB1
+dir_pin: nozzle_mcu:PB0
+enable_pin: !nozzle_mcu:PB2
+microsteps: 16
+rotation_distance: 6.9
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: nozzle_mcu:PB7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: nozzle_mcu:PA0
+pressure_advance: 0.04
+pressure_advance_smooth_time: 0.040
+control: pid
+pid_Kp: 25.013
+pid_Ki: 2.566
+pid_Kd: 60.966
+min_temp: 0
+max_temp: 320
+
+[tmc2209 extruder]
+uart_pin: nozzle_mcu:PB11
+tx_pin: nozzle_mcu:PB10
+uart_address: 3
+run_current: 0.55
+sense_resistor: 0.150
+stealthchop_threshold: 0
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 2
+# driver_TOFF: 3
+# driver_HEND: 0
+# driver_HSTRT: 5
+
+[heater_bed]
+heater_pin: PC8
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_Kp: 37
+pid_Ki: 0.18
+pid_Kd: 280
+min_temp: 0
+max_temp: 125
+
+[filament_switch_sensor filament_sensor]
+pause_on_runout: true
+switch_pin: !PC15
+runout_gcode:
+  {% if printer.extruder.can_extrude|lower == 'true' %}
+    G91
+    G0 E30 F600
+    G90
+  {% endif %}
+
+
+[static_digital_output my_fan_output_pins]
+pins: nozzle_mcu: PB6
+
+[output_pin LED]
+pin:PB0
+pwm: True
+cycle_time: 0.010
+value: 1
+
+[output_pin power]
+pin: PC9
+
+[adxl345]
+cs_pin: nozzle_mcu:PA4
+spi_speed: 5000000
+axes_map: x,-z,y
+spi_software_sclk_pin: nozzle_mcu:PA5
+spi_software_mosi_pin: nozzle_mcu:PA7
+spi_software_miso_pin: nozzle_mcu:PA6
+
+[resonance_tester]
+accel_chip: adxl345
+accel_per_hz: 75
+# min_freq: 30
+# max_freq: 100
+probe_points:
+   150,150,10
+
+[display_status]
+
+[printer]
+kinematics: corexy
+max_velocity: 800
+max_accel: 20000
+max_z_velocity: 20
+square_corner_velocity: 5.0
+max_z_accel: 300
+
+[pause_resume]
+# recover_velocity: 500.
+
+[exclude_object]
diff --git a/printer_configs/k1max/printer_variant1.cfg b/printer_configs/k1max/printer_variant1.cfg
new file mode 100644
index 0000000..b8d7af9
--- /dev/null
+++ b/printer_configs/k1max/printer_variant1.cfg
@@ -0,0 +1,277 @@
+# K1-MAX
+# Printer_size: 300x300x300
+# Version: v1.0.3
+# CreateDate: 2024/01/11
+# Nozzle_mcu: chip: GD32F303CBT6
+#             version: K1-NOZZLE-M_V12
+# Leveling_mcu: chip: GD32E230F8P6
+#             version: K1-MAX-L-V11
+# mcu: chip: GD32F303RET6
+#      version: CR4CU220812S12
+
+[include GuppyScreen/*.cfg]
+[include KAMP/KAMP_Settings.cfg]
+[include sensorless.cfg]
+[include custom_gcode.cfg]
+
+### start probe
+### select and configure one probe, comment the rest
+
+[include btteddy.cfg]
+#[include bltouch.cfg]       ## uncomment if using bltouch
+#[include microprobe.cfg]    ## uncomment if using microprobe
+
+## end probe
+
+[include fluidd.cfg]
+[include fan_control.cfg]
+[include timelapse.cfg]
+
+[mcu]
+serial: /dev/ttyS7
+baud: 230400
+restart_method: command
+
+[mcu nozzle_mcu]
+serial: /dev/ttyS1
+baud: 230400
+restart_method: command
+
+# [mcu leveling_mcu]
+# serial: /dev/ttyS9
+# baud: 230400
+# restart_method: command
+
+[verify_heater extruder]
+[verify_heater heater_bed]
+check_gain_time: 120
+heating_gain: 1.0
+hysteresis: 10
+
+[mcu rpi]
+serial: /tmp/klipper_host_mcu
+
+[idle_timeout]
+timeout: 99999999
+
+[virtual_sdcard]
+path: /root/printer_data/gcodes
+
+[gcode_arcs]
+resolution: 1.0
+
+[temperature_sensor mcu_temp]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[temperature_sensor chamber_temp]
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+min_temp: 0
+max_temp: 125
+
+[temperature_fan _chamber_fan]
+pin: PC0
+cycle_time: 0.0100
+hardware_pwm: false
+max_power: 1
+shutdown_speed: 0
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+min_temp: 0
+max_temp: 70
+control: watermark
+max_delta: 2
+target_temp: 35.0
+max_speed: 1.0
+min_speed: 0.0
+
+[stepper_x]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+microsteps: 32
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_x:virtual_endstop
+position_endstop: 306.5
+position_min: -2
+position_max: 306.5
+homing_speed: 30
+homing_retract_dist:0
+
+[tmc2209 stepper_x]
+uart_pin:PA9
+interpolate: True
+run_current:1.5
+hold_current:1.0
+sense_resistor: 0.100
+stealthchop_threshold: 0
+uart_address:3
+diag_pin: ^PB12
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+driver_TBL: 0
+driver_TOFF: 1
+driver_HEND: 0
+driver_HSTRT: 0
+driver_SGTHRS: 75
+
+[stepper_y]
+step_pin: PB8
+dir_pin: !PB7
+enable_pin: !PC3
+microsteps: 32
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_y:virtual_endstop
+position_endstop: -2
+position_min: -2
+position_max: 306
+homing_speed: 30
+homing_retract_dist:0
+
+[tmc2209 stepper_y]
+uart_pin:PA10
+interpolate: True
+run_current:1.5
+hold_current:1.0
+sense_resistor: 0.100
+stealthchop_threshold: 0
+uart_address:3
+diag_pin: ^PB13
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+driver_TBL: 0
+driver_TOFF: 1
+driver_HEND: 0
+driver_HSTRT: 0
+driver_SGTHRS: 75
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance:8
+gear_ratio: 64:20
+endstop_pin: probe:z_virtual_endstop
+position_max: 305
+position_min: -10
+homing_speed: 10
+second_homing_speed: 1
+homing_retract_dist: 2.0
+
+[tmc2209 stepper_z]
+uart_pin: PA11
+uart_address: 3
+run_current: 0.8
+diag_pin: ^PB14
+stealthchop_threshold: 0
+sense_resistor: 0.100
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 1
+# driver_TOFF: 1
+# driver_HEND: 2
+# driver_HSTRT: 2
+driver_SGTHRS: 0
+
+[extruder]
+max_extrude_only_distance: 1000.0
+max_extrude_cross_section: 80
+step_pin: nozzle_mcu:PB1
+dir_pin: nozzle_mcu:PB0
+enable_pin: !nozzle_mcu:PB2
+microsteps: 16
+rotation_distance: 6.9
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: nozzle_mcu:PB7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: nozzle_mcu:PA0
+pressure_advance: 0.04
+pressure_advance_smooth_time: 0.040
+control: pid
+pid_Kp: 25.013
+pid_Ki: 2.566
+pid_Kd: 60.966
+min_temp: 0
+max_temp: 320
+
+[tmc2209 extruder]
+uart_pin: nozzle_mcu:PB11
+tx_pin: nozzle_mcu:PB10
+uart_address: 3
+run_current: 0.55
+sense_resistor: 0.150
+stealthchop_threshold: 0
+# driver_IHOLDDELAY: 8
+# driver_TPOWERDOWN: 20
+# driver_TBL: 2
+# driver_TOFF: 3
+# driver_HEND: 0
+# driver_HSTRT: 5
+
+[heater_bed]
+heater_pin: PC8
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_Kp: 37
+pid_Ki: 0.18
+pid_Kd: 280
+min_temp: 0
+max_temp: 125
+
+[filament_switch_sensor filament_sensor]
+pause_on_runout: true
+switch_pin: !PC15
+runout_gcode:
+  {% if printer.extruder.can_extrude|lower == 'true' %}
+    G91
+    G0 E30 F600
+    G90
+  {% endif %}
+
+[static_digital_output my_fan_output_pins]
+pins: nozzle_mcu: PB6
+
+[output_pin LED]
+pin:PB0
+pwm: True
+cycle_time: 0.010
+value: 1
+
+[output_pin power]
+pin: PC9
+
+[adxl345]
+cs_pin: nozzle_mcu:PA4
+spi_speed: 5000000
+axes_map: x,-z,y
+spi_software_sclk_pin: nozzle_mcu:PA5
+spi_software_mosi_pin: nozzle_mcu:PA7
+spi_software_miso_pin: nozzle_mcu:PA6
+
+[resonance_tester]
+accel_chip: adxl345
+accel_per_hz: 75
+# min_freq: 30
+# max_freq: 100
+probe_points:
+   150,150,10
+
+[display_status]
+
+[printer]
+kinematics: corexy
+max_velocity: 800
+max_accel: 20000
+max_z_velocity: 20
+square_corner_velocity: 5.0
+max_z_accel: 300
+
+[pause_resume]
+# recover_velocity: 500.
+
+[exclude_object]
diff --git a/printer_configs/prompts/eddysetup.cfg b/printer_configs/prompts/eddysetup.cfg
new file mode 100644
index 0000000..250ee69
--- /dev/null
+++ b/printer_configs/prompts/eddysetup.cfg
@@ -0,0 +1,37 @@
+### eddy helpers
+[gcode_shell_command btt_eddy_flash]
+command: /usr/bin/rp2040_flash
+timeout: 600.0
+verbose: True
+
+[gcode_shell_command klipper_restart]
+command: /etc/init.d/S60klipper
+timeout: 600.0
+verbose: True
+
+[gcode_macro _KLIPPER_RESTART]
+gcode:
+    RESPOND TYPE=command MSG="action:prompt_end"
+
+    RUN_SHELL_COMMAND CMD=klipper_restart PARAMS="restart"
+
+
+[gcode_macro BTT_EDDY_FLASH_FIRMWARE]
+description: Use to flash your BTT Eddy with the latest firmware
+gcode:
+    RESPOND TYPE=command MSG="action:prompt_begin Flash BTT Eddy Firmare"
+    RESPOND TYPE=command MSG="action:prompt_text Hold BOOT on top of BTT Eddy and plug it into the front USB port"
+    RESPOND TYPE=command MSG="action:prompt_footer_button Flash|_FLASH_BTT_EDDY|primary"    
+    RESPOND TYPE=command MSG="action:prompt_footer_button Abort|RESPOND TYPE=command MSG=action:prompt_end"
+    RESPOND TYPE=command MSG="action:prompt_show"
+
+[gcode_macro _FLASH_BTT_EDDY]
+gcode:
+    RUN_SHELL_COMMAND CMD=btt_eddy_flash PARAMS="/root/firmwares/btt-eddy-mainline.uf2"
+    RESPOND TYPE=command MSG="action:prompt_end"
+
+    RESPOND TYPE=command MSG="action:prompt_begin Restart Klipper"
+    RESPOND TYPE=command MSG="action:prompt_text Firmware is flashed. Restart Klipper to continue."
+    RESPOND TYPE=command MSG="action:prompt_footer_button Restart|_KLIPPER_RESTART|primary"    
+    RESPOND TYPE=command MSG="action:prompt_footer_button Abort|RESPOND TYPE=command MSG=action:prompt_end"
+    RESPOND TYPE=command MSG="action:prompt_show"