Yoctopuce Yocto-VOC-V3 with Artisan for tracking humidity at the exhaust

[McPatPyhton]

Hello,

I would like to track the humidity at the exhaust port of my roaster and considering to track in Artisan with Yoctopuce Yocto-VOC-V3 (https://www.yoctopuce.com/EN/products/usb-environmental-sensors/yocto-voc-v3) . now, i noted that the device is not directly supported but Artisan propose the Yocto Sensor (https://artisan-scope.org/devices/yoctopuce/) Now, can i add the VOC-V3 with the Yocto Sensor addition in Extra Devices ? And if so, how can i access the Humidity Sensor, one of the 4 sensors proposed by the VOC-V3? Note that i am running with Artisan 2.8.2 Thanks , Patrick

[darrenaddy]

" the relative humidity scale is essentially useless or even misleading at temperatures above 100°C." Source: https://macinstruments.com/blog/whats-wrong-with-relative-humidity-above-100-celsius/ Respectfully, Darren Addy Kearney, Nebraska

…

On Tue, Apr 9, 2024 at 2:59 PM McPatPyhton ***@***.***> wrote: Hello, I would like to track the humidity at the exhaust port of my roaster and considering to track in Artisan with Yoctopuce Yocto-VOC-V3 ( https://www.yoctopuce.com/EN/products/usb-environmental-sensors/yocto-voc-v3) . now, i noted that the device is not directly supported but Artisan propose the Yocto Sensor (https://artisan-scope.org/devices/yoctopuce/) Now, can i add the VOC-V3 with the Yocto Sensor addition in Extra Devices ? And if so, how can i access the Humidity Sensor, one of the 4 sensors proposed by the VOC-V3? Note that i am running with Artisan 2.8.2 Thanks , Patrick — Reply to this email directly, view it on GitHub <#1534>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AO5YMLSIPPEAGUOMSGZRBBDY4RCAZAVCNFSM6AAAAABF7F7ZP2VHI2DSMVQWIX3LMV43ERDJONRXK43TNFXW4OZWGQ4DINJQGE> . You are receiving this because you are subscribed to this thread.Message ID: ***@***.***>

[McPatPyhton]

Hello,

Thank you for your reply, i will precise i will not attempt to put the VOC-V3 directly at the exhaust port, but near enough. So, to avoid exceeding the limit of the VOC V3 and what you mention.

Regards,
Patrick

[darrenaddy]

Just to be clear, I wasn't talking about exceeding the limit of the VOC V3. I was talking about the folly of attempting to measure relative humidity of air that is over 100C. Respectfully, Darren Addy Kearney, NE

…

On Tue, Apr 9, 2024 at 3:48 PM McPatPyhton ***@***.***> wrote: Hello, Thank you for your reply, i will precise i will not attempt to put the VOC-V3 directly at the exhaust port, but near enough. So, to avoid exceeding the limit of the VOC V3 and what you mention. Regards, Patrick — Reply to this email directly, view it on GitHub <#1534 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AO5YMLSUHKFAZXAQDGVSGDLY4RHYBAVCNFSM6AAAAABF7F7ZP2VHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TANRTG43DI> . You are receiving this because you commented.Message ID: <artisan-roaster-scope/artisan/repo-discussions/1534/comments/9063764@ github.com>

[McPatPyhton]

Hello Darren,

Understood, for information the idea that i am planning to adapt for my roaster is based on this idea
https://www.home-barista.com/roasting/humidity-sensor-on-exhaust-other-gas-sensors-t87191.html

Regards,
Patrick

[MAKOMO]

I haven't tested this for lack of hardware, but the Artisan YoctoSensor device type binds its two channels to any Yoctopuce sensor interface (YSensor) not yet allocated. Thus you need to add several of those YoctoSensor devices to bind to all published sensors of that module and just deactivate/hide those you are not interested in. Artisan does not provide a UI to specify the exact channel you want YoctoSensor to bind too. However, at anytime you can write script that reads data from any source you are interested in and run it as External Program to the ET/BT tab of the Device dialog.

[McPatPyhton]

Hello,

Thank you for the information, i will check the YoctoSensor the functionality when I receive the device. I currently use the version 2.8.2

Regards,
Patrick