fixed time period on/off

[JaDiko]

Hello,
I would like to ask for help in solving a problem.
I want to have a TASMOTA 8266
(https://bilder.obi.sk/93aaded6-d082-4945-8b53-8957f5f059e8/prZZO/5543228.jpg)
set so that when I plug it in, it turns on after 15 minutes, stays on for 3 minutes and then turns off. This is how it should work 24/7.
I don't want any solution using MQTT or anything else.
I just want a "magic" rule or "something" that will allow me to do this.
The above socket wakes up the modem, wifi for 3 minutes after 15 minutes and sends me the measured values, but then I need the modem, wifi, probes to be off.
Don't tell me that such a sophisticated device can't handle it, I guess it's not just worse than this:
https://media.hornbach.sk/hb/packshot/as.46488068.jpg?dvid=8
because that's also a solution
Thanks for the help.

[lalo-uy]

Just set pulsetime to 300 sec ( 5min) and a rule triggered on boot to 900 sec that set power on PulseTime 300 Rule1 ON system#boot do RuleTimer1 900 ENDON ON Rules#Timer=1 DO Power1 on ENDON El El lun, 25 nov. 2024 a la(s) 09:24, JaDiko ***@***.***> escribió:

…

Hello, I would like to ask for help in solving a problem. I want to have a TASMOTA 8266 ( https://bilder.obi.sk/93aaded6-d082-4945-8b53-8957f5f059e8/prZZO/5543228.jpg ) set so that when I plug it in, it turns on after 15 minutes, stays on for 3 minutes and then turns off. This is how it should work 24/7. I don't want any solution using MQTT or anything else. I just want a "magic" rule or "something" that will allow me to do this. The above socket wakes up the modem, wifi for 3 minutes after 15 minutes and sends me the measured values, but then I need the modem, wifi, probes to be off. Don't tell me that such a sophisticated device can't handle it, I guess it's not just worse than this: https://media.hornbach.sk/hb/packshot/as.46488068.jpg?dvid=8 because that's also a solution Thanks for the help. — Reply to this email directly, view it on GitHub <#22547>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ACXBW4M3B3MTQX5E4LWL2GT2CMJJXAVCNFSM6AAAAABSN3QXDOVHI2DSMVQWIX3LMV43ERDJONRXK43TNFXW4OZXGU2TEOBQGU> . You are receiving this because you are subscribed to this thread.Message ID: ***@***.***>

[sfromis]

If you want it to repeat, change the last rule to
ON Rules#Timer=1 DO Backlog Power1 on; RuleTimer1 900 ENDON
Otherwise it is once-only.

Beware that without Wifi, Tasmota is not fully initialized, and timing may not work well, but using System#Init instead of System#Boot lets it start even before full initialization.

[JaDiko]

Hi,
I tried to enter it through the console, but it doesn't work.
Are you sure this is correct?
I'm running 12.3.1(tasmota), but there is no problem upgrading.
On the console it looks like this:
PulseTime Ent
RESULT = {"PulseTime":{"Set":[60,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0],"Remaining":[0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0]}}
Rule1 Ent
RESULT = {"Rule1":{"State":"OFF","Once":"OFF","StopOnError":"OFF","Length":38,"Free":473,"Rules":"ON system#boot do RuleTimer1 120 ENDON"}}
ON Rules#Timer=1 DO Backlog Power1 on; RuleTimer1 900 ENDON Ent
RESULT = {"Command":"Unknown"}
I've shortened the time, but the third set doesn't work.

I'm not very good at this, so I'd like to ask for help.
Thanks

[sfromis]

Rule1 is the command for rule set 1, and on ... endon is the content; has to be one line, including multiple rules, each of which are on ... endon. Both rules are on the same line as the Rule1 command.

Also, after inputting the rule set, you'll have to activate it by another command, Rule1 1