Support for ESP32-GEEK Development Board

[jkwim]

There is a new product in Aliexpress:
https://vi.aliexpress.com/item/1005006406976102.html?

Based On ESP32-S3R2

Comes with 1.14inch 65K Color LCD.

[] ESP32-S3-GEEK is a geek development board designed by Waveshare, onboard USB-A port, 1.14inch LCD screen, TF card slot, and other peripherals. Supports 2.4GHz WiFi and BLE 5, with integrated 16MB Flash & 2MB PSRAM, provides I2C port, UART port, and GPIO header, bringing more possibilities for your project.

[] Key features include:

[] Adopts ESP32-S3R2 chip with Xtensa® 32-bit LX7 dual-core processor, capable of running at 240 MHz

[] Built in 512KB SRAM, 384KB ROM, 2MB of on-chip PSRAM, and onboard 16MB Flash memory

[] Onboard 1.14inch 240×135 pixels 65K color IPS LCD display

[] Integrated 2.4GHz WiFi and Bluetooth LE wireless communication

-WiFi supports Infrastructure BSS in Station, SoftAP, and Station + SoftAP modes

-WiFi supports 1T1R mode with data rate up to 150 Mbps

-Bluetooth supports high power mode (20dBm)

-Internal co-existence mechanism between Wi-Fi and Bluetooth to share the same antenna

[] Onboard 3PIN UART port, 3PIN GPIO header and 4PIN I2C port

[] Equipped with plastic case and cables

[] Provides online open-source demo and resources, more convenient for learning and development

I also saw
[Support for ESP32-S3-BOX-3 #19471]#19471

Will Tasmota S3 build run on this device as well?

[Jason2866]

It will work. For the display "just" the needed display.ini needs to be configured.
Flashing the S3 LVGL Haspmota build and the device will start Tasmota already

[HaraldKiessling]

i found a description for ESPhome
WaveShare ESP32-S3-GEEK
This worked fine with the display. Writing date an time an the display.

But i would preferre tasmota

[HaraldKiessling]

It's a little more better:

the console

SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce2820,len:0x1ac
load:0x403c8700,len:0x4
load:0x403c8704,len:0xb2c
load:0x403cb700,len:0x27e4
SHA-256 comparison failed:
Calculated: 9da421cbddfc8f787b5116a851487bffc60043da94939dbbc4d62970133b4edc
Expected: a412dcd4c77e9af49fd629493ae06bb0e3c85e0e6b76697dc1e10b4cb634b715
Attempting to boot anyway...
entry 0x403c8868

00:00:00.001 CMD: Using USB CDC
00:00:00.001 HDW: ESP32-S3 v0.2 (PSRAM)
00:00:00.024 UFS: FlashFS mounted with 12424 kB free
00:00:00.033 CFG: Loaded from File, Count 65
00:00:00.034 SER: Set to 8N1 115200 bit/s
00:00:00.034 SER: HWCDC supports 115200 bit/s only
00:00:00.039 QPC: Count 1
00:00:00.042 I2C: Bus1 using GPIO17(SCL) and GPIO18(SDA)
00:00:00.072 BRY: Berry initialized, RAM used 5252 bytes
00:00:01.186 DSP: ST7789 initialized
00:00:01.192 Project tasmota - Tasmota Version 14.3.0.7(4925e9c-lvgl-haspmota)-3_1_0(2024-11-22T21:48:20)
00:00:01.199 LVG: LVGL initialized
00:00:01.199 LVG: LVGL initialized
00:00:01.419 TAP: Loaded Tasmota App 'haspmota_demo.tapp'
00:00:05.849 WIF: Connecting to AP1 miVida2 Channel 11 BSSId 3C:A6:2F:D8:ED:FA in mode HT40 as tasmota-26D7BC-6076...
00:00:07.113 WIF: Connected
00:00:07.373 HTP: Web server active on tasmota-26D7BC-6076 with IP address 192.168.0.119
17:04:46.369 RSL: INFO1 = {"Info1":{"Module":"Lilygo S3 Display","Version":"14.3.0.7(4925e9c-lvgl-haspmota)","FallbackTopic":"cmnd/DVES_26D7BC_fb/","GroupTopic":"cmnd/tasmotas/"}}
17:04:46.374 RSL: INFO2 = {"Info2":{"WebServerMode":"Admin","Hostname":"tasmota-26D7BC-6076","IPAddress":"192.168.0.119","IP6Global":"","IP6Local":"fe80::3e84:27ff:fe26:d7bc%st1"}}
17:04:46.379 RSL: INFO3 = {"Info3":{"RestartReason":"Usb uart reset digital core","BootCount":26}}
17:04:46.384 RSL: RESULT = {"POWER":"ON"}
17:04:46.385 RSL: POWER = ON
17:04:49.712 QPC: Reset
17:04:50.724 RSL: STATE = {"Time":"2024-11-23T17:04:50","Uptime":"0T00:00:08","UptimeSec":8,"Heap":216,"SleepMode":"Dynamic","Sleep":10,"LoadAvg":99,"MqttCount":0,"Berry":{"HeapUsed":35,"Objects":639},"POWER":"ON","Wifi":{"AP":1,"SSId":"miVida2","BSSId":"3C:A6:2F:D8:ED:FA","Channel":11,"Mode":"HT40","RSSI":100,"Signal":-30,"LinkCount":1,"Downtime":"0T00:00:03"}}
17:04:50.766 RSL: SENSOR = {"Time":"2024-11-23T17:04:50","ANALOG":{"Range1":2}}

[HaraldKiessling]

changing the first line from:
:H,ST7789,135,240,16,SPI,3,10,12,11,8,7,9,-1,40
to (135 <-> 240)
:H,ST7789,240,135,16,SPI,3,10,12,11,8,7,9,-1,40

[HaraldKiessling]

do you agree, LVGL ist correct configured?

Ist this only a problem of the Tasmota App 'haspmota_demo.tapp'?

[s-hadinger]

It's good news.

First colors are inverted so put instead

:i,20,21

Next you need to change the internal offset of the display. I don't have the datasheet at hand but chances are that you need to adjust the last byte of

3A,81,55
36,81,00