^Top
The client and the Proxmark3 firmware should always be in sync. Nevertheless, the firmware can be tuned depending on the Proxmark3 platform and options.
Indeed, the Iceman fork can be used on other Proxmark3 hardware platforms as well.
Via some definitions, you can adjust the firmware for a given platform, but also to add features like the support of the Blue Shark add-on or to select which standalone mode to embed. To learn how to adjust the firmware, please read Advanced compilation parameters.
^Top
The repo defaults for compiling a firmware and client suitable for Proxmark3 RDV4.
^Top
In order to build this repo for generic Proxmark3 platforms we urge you to read Advanced compilation parameters
^Top
cd proxmark3
git pull^Top
make clean && make -j^Top
Read the troubleshooting guide,
For instance, on WSl-1 you usually get the libQt5Core.so.5 not found message
solution
^Top
This is an optional step. If you do
sudo make installThen the required files will be installed on your system, by default in /usr/local/bin and /usr/local/share/proxmark3.
Maintainers can read this doc to learn how to modify installation paths via DESTDIR and PREFIX Makefile variables.
The commands given in the documentation assume you did the installation step. If you didn't, you've to adjust the commands paths and files paths accordingly,
e.g. calling ./pm3 or client/proxmark3 instead of just pm3 or proxmark3.
^Top
In most cases, you can run the following script which try to auto-detect the port to use, on several OS:
pm3-flash-allFor the other cases, specify the port by yourself. For example, for a Proxmark3 connected via USB under Linux (adjust the port for your OS):
proxmark3 /dev/ttyACM0 --flash --unlock-bootloader --image bootrom.elf --image fullimage.elfThe firmware files will be searched in the expected locations (installed files, working repo files, user folder, etc.). You can also specify their location:
pm3-flash -b /tmp/my-bootrom.elf /tmp/my-fullimage.elfor
proxmark3 /dev/ttyACM0 --flash --unlock-bootloader --image /tmp/my-bootrom.elf --image /tmp/my-fullimage.elfIf the flasher can't detect your Proxmark3 (especially the very first time you flash a new device), force it to enter the bootloader mode as following:
With your Proxmark3 unplugged from your machine, press and hold the button on your Proxmark3 as you plug it into a USB port. You can release the button, two of the four LEDs should stay on. You're in bootloader mode, ready for the next step. In case the two LEDs don't stay on when you're releasing the button, you've a very old bootloader, start over and keep the button pressed during the whole flashing procedure.
^Top
The Proxmark3 software and firmware is connected tightly. The strong recommendation is to use the client with a Proxmark3 device flashed with firmware images from same source version.
In the flash process you might get this message because the firmware images is downloaded or distributed and you have compiled your own client from a different source version.
To minimize the risks the flasher warns about it and stops.
Make sure to flash a correct and up-to-date version
You can force flashing this firmware by using the option '--force'
If you know what you are doing and want to proceed despite the mismatch, you need to add the --force param in order to continue flashing.
pm3-flash-all --force^Top
In most cases, you can run the script pm3 which try to auto-detect the port to use, on several OS.
./pm3For the other cases, specify the port by yourself. For example, for a Proxmark3 connected via USB under Linux:
Here, for example, for a Proxmark3 connected via USB under Linux (adjust the port for your OS):
proxmark3 /dev/ttyACM0or from the local repo
client/proxmark3 /dev/ttyACM0^Top
For the next steps, please read the following pages: