Update bootstrap.sh

rpi/.bash_profile

@@ -5,3 +5,7 @@ then
     startx
   done
 fi
+
+if [ -f ~/.bashrc ]; then
+  . ~/.bashrc
+fi

rpi/.xinitrc

@@ -11,4 +11,7 @@ unclutter -idle 0 &
 xrandr --output HDMI-1 --mode 1024x768
 
 # Start browser in kiosk mode
-chromium-browser http://localhost:8082 --start-fullscreen --kiosk --incognito --noerrdialogs --no-first-run --disk-cache-dir=/dev/null
+#chromium-browser http://localhost:8082 --start-fullscreen --kiosk --incognito --noerrdialogs --no-first-run --disk-cache-dir=/dev/null
+
+# Start nw.js
+nwjs ~/nwjs

rpi/bootstrap.sh

@@ -1,6 +1,6 @@
 #!/usr/bin/env bash
 
-set -eu
+set -Eeuo pipefail
 
 SCRIPT_DIR="$(cd "$(dirname "${BASH_SOURCE[0]}")" >/dev/null 2>&1 && pwd)"
 
@@ -36,6 +36,7 @@ function installBrowser() {
     sudo apt-get install --no-install-recommends -y \
         xserver-xorg-video-all xserver-xorg-input-all xserver-xorg-core xinit x11-xserver-utils \
         unclutter \
+        xinput \
         chromium-browser
 
     # Enable Auto-Login on console
@@ -49,10 +50,26 @@ function installBrowser() {
     cp "${SCRIPT_DIR}/.bash_profile" ~/.bash_profile
 }
 
+function install_nwjs() {
+    sudo apt install apt-transport-https
+    sudo apt-key adv --keyserver keyserver.ubuntu.com --recv-keys DB348A58A292E9BC
+    echo "deb https://repo.netsyms.com/apt main main" | sudo tee /etc/apt/sources.list.d/netsyms.list
+    sudo apt update
+    sudo apt install nw.js-normal
+    mkdir -p ~/nwjs
+    cp "${SCRIPT_DIR}/package.json" ~/nwjs
+}
+
+function configurePi() {
+    sudo cp "${SCRIPT_DIR}/config.txt" /boot/config.txt
+}
+
 updateSystem
 installService
 installStatusBoard
 installBrowser
+install_nwjs
+configurePi
 
 echo "You may need to restart the system to apply some settings. Reboot now? (y/n)"
 read -r response

rpi/config.txt

@@ -0,0 +1,81 @@
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+#hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+#dtparam=i2c_arm=on
+#dtparam=i2s=on
+#dtparam=spi=on
+
+# Uncomment this to enable infrared communication.
+#dtoverlay=gpio-ir,gpio_pin=17
+#dtoverlay=gpio-ir-tx,gpio_pin=18
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+# Automatically load overlays for detected cameras
+#camera_auto_detect=1
+
+# Automatically load overlays for detected DSI displays
+display_auto_detect=1
+
+# Enable DRM VC4 V3D driver
+dtoverlay=vc4-fkms-v3d
+max_framebuffers=2
+
+# Disable compensation for displays with overscan
+disable_overscan=1
+
+[cm4]
+# Enable host mode on the 2711 built-in XHCI USB controller.
+# This line should be removed if the legacy DWC2 controller is required
+# (e.g. for USB device mode) or if USB support is not required.
+otg_mode=1
+
+[all]
+
+[pi4]
+# Run as fast as firmware / board allows
+arm_boost=1
+
+[all]
+avoid_warnings=1