Replies: 3 comments
-
I don't think you understand. This is to report issues for the firmware.
The Facebook page is for help with prints and settings. The firmware has no
issues.
…On Tue, Jul 4, 2023, 1:20 PM RichBr1 ***@***.***> wrote:
Cannot get any decent prints out of the Neptune 3 using Cura latest and
Neptune 3 profiles. for PETG. Stringing everywhere and terrible top layers.
Have spent hours changing everything in Cura (temp, speed and many other
settings) but nothing works,?
PLA works a treat.
Anybody know of a magic setting to cure this.
Tried all temps from 210 to 245, Run at 40 , 50 and 60 mm/s
Fan from 20% to %0 %
Fills from 10 to 30%
Retraaction fro 2 to 6 mm
Brand new Eryone PETG White
Completely baffled
—
Reply to this email directly, view it on GitHub
<#72>, or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ADL5M6XQPCINNKVYOXWUTELXORGEJANCNFSM6AAAAAAZ57Q23I>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
0 replies
-
Apologies, it was not very clear what this site was for, will try elsewhere.Sent from Android deviceOn 4 Jul 2023 18:26, Moody66 ***@***.***> wrote:
I don't think you understand. This is to report issues for the firmware.
The Facebook page is for help with prints and settings. The firmware has no
issues.
On Tue, Jul 4, 2023, 1:20 PM RichBr1 ***@***.***> wrote:
Cannot get any decent prints out of the Neptune 3 using Cura latest and
Neptune 3 profiles. for PETG. Stringing everywhere and terrible top layers.
Have spent hours changing everything in Cura (temp, speed and many other
settings) but nothing works,?
PLA works a treat.
Anybody know of a magic setting to cure this.
Tried all temps from 210 to 245, Run at 40 , 50 and 60 mm/s
Fan from 20% to %0 %
Fills from 10 to 30%
Retraaction fro 2 to 6 mm
Brand new Eryone PETG White
Completely baffled
—
Reply to this email directly, view it on GitHub
<#72>, or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ADL5M6XQPCINNKVYOXWUTELXORGEJANCNFSM6AAAAAAZ57Q23I>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you authored the thread.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
0 replies
-
Join the Facebook group. That is to help people for prints. We are all
there. https://m.facebook.com/groups/192499235897759/
…On Tue, Jul 4, 2023, 1:20 PM RichBr1 ***@***.***> wrote:
Cannot get any decent prints out of the Neptune 3 using Cura latest and
Neptune 3 profiles. for PETG. Stringing everywhere and terrible top layers.
Have spent hours changing everything in Cura (temp, speed and many other
settings) but nothing works,?
PLA works a treat.
Anybody know of a magic setting to cure this.
Tried all temps from 210 to 245, Run at 40 , 50 and 60 mm/s
Fan from 20% to %0 %
Fills from 10 to 30%
Retraaction fro 2 to 6 mm
Brand new Eryone PETG White
Completely baffled
—
Reply to this email directly, view it on GitHub
<#72>, or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ADL5M6XQPCINNKVYOXWUTELXORGEJANCNFSM6AAAAAAZ57Q23I>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
0 replies
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
-
Cannot get any decent prints out of the Neptune 3 using Cura latest and Neptune 3 profiles. for PETG. Stringing everywhere and terrible top layers. Have spent hours changing everything in Cura (temp, speed and many other settings) but nothing works,?
PLA works a treat.
Anybody know of a magic setting to cure this.
Tried all temps from 210 to 245, Run at 40 , 50 and 60 mm/s
Fan from 20% to %0 %
Fills from 10 to 30%
Retraaction fro 2 to 6 mm
Brand new Eryone PETG White
Completely baffled
Beta Was this translation helpful? Give feedback.
All reactions