\mainpage Main Page
BATT Boost Click is a compact add-on board that expands a coin battery cell's lifetime and current capability, like the CR2032 and lithium thionyl batteries. This board features the NBM5100A, a coin-cell battery life booster with adaptive power optimization from Nexperia. It is a battery energy management device designed to maximize usable capacity from non-rechargeable, primary batteries when used in low-voltage, low-power applications requiring burst current loads. The devices overcome voltage drop and battery life limitations associated with extracting high pulse currents.
- Author : Nenad Filipovic
- Date : Oct 2023.
- Type : I2C type
We provide a library for the BATT Boost Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.
This library contains API for BATT Boost Click driver.
battboost_cfg_setupConfig Object Initialization function.
void battboost_cfg_setup ( battboost_cfg_t *cfg );battboost_initInitialization function.
err_t battboost_init ( battboost_t *ctx, battboost_cfg_t *cfg );battboost_default_cfgClick Default Configuration function.
err_t battboost_default_cfg ( battboost_t *ctx );battboost_get_vcapThis function is used to read the storage capacitor voltage status.
err_t battboost_get_vcap ( battboost_t *ctx, float *vcap );battboost_set_op_modeThis function is used to select the desired operating mode of the device.
err_t battboost_set_op_mode ( battboost_t *ctx, uint8_t op_mode );battboost_get_statusThis function reads the the status information of low battery input, capacitor input voltage early warning, VDH output alarm and ready state.
err_t battboost_get_status ( battboost_t *ctx, uint8_t *status );This library contains API for the BATT Boost Click driver. This driver provides the functions to controle battery energy management device designed to maximize usable capacity from non-rechargeable.
The demo application is composed of two sections :
Initialization of I2C module and log UART. After driver initialization, the app executes a default configuration, sets the output voltage to 1.8V, charge current to 16mA, and early warning voltage to 2.6V.
void application_init ( void )
{
log_cfg_t log_cfg; /**< Logger config object. */
battboost_cfg_t battboost_cfg; /**< Click config object. */
/**
* Logger initialization.
* Default baud rate: 115200
* Default log level: LOG_LEVEL_DEBUG
* @note If USB_UART_RX and USB_UART_TX
* are defined as HAL_PIN_NC, you will
* need to define them manually for log to work.
* See @b LOG_MAP_USB_UART macro definition for detailed explanation.
*/
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, " Application Init " );
// Click initialization.
battboost_cfg_setup( &battboost_cfg );
BATTBOOST_MAP_MIKROBUS( battboost_cfg, MIKROBUS_1 );
if ( I2C_MASTER_ERROR == battboost_init( &battboost, &battboost_cfg ) )
{
log_error( &logger, " Communication init." );
for ( ; ; );
}
if ( BATTBOOST_ERROR == battboost_default_cfg ( &battboost ) )
{
log_error( &logger, " Default configuration." );
for ( ; ; );
}
log_info( &logger, " Application Task " );
Delay_ms ( 100 );
}This example demonstrates the use of the BATT Boost Click board. The demo application uses two operations in two states: the charging state and the active state. First, when the device is in a Charge state, the external storage capacitor is charging from VBT using a constant current and displays storage capacitor voltage levels and charge cycle count. Upon completion of a Charge state, the device transitions to the Active state at which time VDH becomes a regulated voltage output of 1.8V (default configuration), displays storage capacitor voltage level, and monitors alarms for low output voltage (below 1.8V) and early warning (below 2.4V). Results are being sent to the UART Terminal, where you can track their changes.
void application_task ( void )
{
float vcap = 0;
uint8_t status = 0;
uint32_t chenergy = 0;
if ( BATTBOOST_STATUS_READY != battboost_get_ready( &battboost ) )
{
if ( BATTBOOST_OK == battboost_set_op_mode( &battboost, BATTBOOST_OP_MODE_CHARGE ) )
{
log_printf( &logger, "\nOperating state: Charge\r\n" );
}
if ( BATTBOOST_OK == battboost_get_vcap( &battboost, &vcap ) )
{
log_printf( &logger, " Capacitor Voltage: %.2f V \r\n", vcap );
}
if ( BATTBOOST_OK == battboost_get_chenergy( &battboost, &chenergy ) )
{
log_printf( &logger, " Charge cycle count: %lu \r\n", chenergy );
}
Delay_ms ( 1000 );
}
else
{
if ( BATTBOOST_OK == battboost_set_op_mode( &battboost, BATTBOOST_OP_MODE_ACTIVE ) )
{
log_printf( &logger, "\nOperating state: Active\r\n" );
if ( BATTBOOST_OK == battboost_get_vcap( &battboost, &vcap ) )
{
log_printf( &logger, " Capacitor Voltage: %.2f V \r\n", vcap );
}
if ( BATTBOOST_OK == battboost_get_status( &battboost, &status ) )
{
if ( BATTBOOST_STATUS_EW & status )
{
log_printf( &logger, " Status: Early warning.\r\n" );
}
if ( BATTBOOST_STATUS_ALRM & status )
{
log_printf( &logger, " Status: Low output voltage in the Active state.\r\n" );
}
}
}
Delay_ms ( 1000 );
}
}The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.
Other Mikroe Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.BATTBoost
Additional notes and informations
Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.