\mainpage Main Page
1x4 RGB Click is a compact add-on board that creates vivid and dynamic lighting effects. This board features the LP5812, an advanced RGB LED driver from Texas Instruments. It features ultra-low operation current, an autonomous animation engine, and support for both analog and PWM dimming. The board operates with 3.3V or 5V logic voltage levels and communicates with the host MCU via a standard 2-wire I2C interface. It is suitable for portable and wearable electronics, gaming, home entertainment, IoT, networking, industrial HMI, and many more.
- Author : Nenad Filipovic
- Date : Feb 2024.
- Type : I2C type
We provide a library for the 1x4 RGB Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.
This library contains API for 1x4 RGB Click driver.
c1x4rgb_cfg_setup
Config Object Initialization function.
void c1x4rgb_cfg_setup ( c1x4rgb_cfg_t *cfg );
c1x4rgb_init
Initialization function.
err_t c1x4rgb_init ( c1x4rgb_t *ctx, c1x4rgb_cfg_t *cfg );
c1x4rgb_default_cfg
Click Default Configuration function.
err_t c1x4rgb_default_cfg ( c1x4rgb_t *ctx );
c1x4rgb_set_rgb_color
This function sets the desired values of RGB colors for the selected LED by using the I2C serial interface.
err_t c1x4rgb_set_rgb_color ( c1x4rgb_t *ctx, uint8_t led_pos, uint8_t red, uint8_t green, uint8_t blue );
c1x4rgb_enable_leds
This function turns on the desired LEDs by using the I2C serial interface.
err_t c1x4rgb_enable_leds ( c1x4rgb_t *ctx, uint16_t led_bitmask );
c1x4rgb_set_tmc_mode
This function configures the desired LED drive mode as TCM 1/2/3/4 scans using the I2C serial interface.
err_t c1x4rgb_set_tmc_mode ( c1x4rgb_t *ctx, uint8_t dev_cfg, uint8_t mode );
This example demonstrates the use of the 1x4 RGB Click board by controlling the color of the LEDs [LD1-LD4].
The demo application is composed of two sections :
Initialization of I2C module and log UART. After driver initialization, the app executes a default configuration.
void application_init ( void )
{
log_cfg_t log_cfg; /**< Logger config object. */
c1x4rgb_cfg_t c1x4rgb_cfg; /**< Click config object. */
/**
* Logger initialization.
* Default baud rate: 115200
* Default log level: LOG_LEVEL_DEBUG
* @note If USB_UART_RX and USB_UART_TX
* are defined as HAL_PIN_NC, you will
* need to define them manually for log to work.
* See @b LOG_MAP_USB_UART macro definition for detailed explanation.
*/
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, " Application Init " );
// Click initialization.
c1x4rgb_cfg_setup( &c1x4rgb_cfg );
C1X4RGB_MAP_MIKROBUS( c1x4rgb_cfg, MIKROBUS_1 );
if ( I2C_MASTER_ERROR == c1x4rgb_init( &c1x4rgb, &c1x4rgb_cfg ) )
{
log_error( &logger, " Communication init." );
for ( ; ; );
}
if ( C1X4RGB_ERROR == c1x4rgb_default_cfg ( &c1x4rgb ) )
{
log_error( &logger, " Default configuration." );
for ( ; ; );
}
log_info( &logger, " Application Task " );
Delay_ms ( 1000 );
}
The demo example shows the color change of four RGB LEDs, starting with red color, through green and blue, and ending with white. These LEDs actually consist of three single-colored LEDs (Red-Green-Blue) in a single package. Various colors can be reproduced by mixing the intensity of each LED.
void application_task ( void )
{
log_printf( &logger, "\r\n\n RED: " );
for ( uint8_t led_pos = C1X4RGB_LED_POS_LD1; led_pos <= C1X4RGB_LED_POS_LD4; led_pos++ )
{
if ( C1X4RGB_OK == c1x4rgb_set_rgb_color( &c1x4rgb, led_pos, DEMO_COLOR_INT_100,
DEMO_COLOR_INT_0,
DEMO_COLOR_INT_0 ) )
{
log_printf( &logger, " LD%d ", ( uint16_t ) led_pos );
Delay_ms ( 100 );
}
}
log_printf( &logger, "\r\n GREEN: " );
for ( uint8_t led_pos = C1X4RGB_LED_POS_LD1; led_pos <= C1X4RGB_LED_POS_LD4; led_pos++ )
{
if ( C1X4RGB_OK == c1x4rgb_set_rgb_color( &c1x4rgb, led_pos, DEMO_COLOR_INT_0,
DEMO_COLOR_INT_100,
DEMO_COLOR_INT_0 ) )
{
log_printf( &logger, " LD%d ", ( uint16_t ) led_pos );
Delay_ms ( 100 );
}
}
log_printf( &logger, "\r\n BLUE: " );
for ( uint8_t led_pos = C1X4RGB_LED_POS_LD1; led_pos <= C1X4RGB_LED_POS_LD4; led_pos++ )
{
if ( C1X4RGB_OK == c1x4rgb_set_rgb_color( &c1x4rgb, led_pos, DEMO_COLOR_INT_0,
DEMO_COLOR_INT_0,
DEMO_COLOR_INT_100 ) )
{
log_printf( &logger, " LD%d ", ( uint16_t ) led_pos );
Delay_ms ( 100 );
}
}
log_printf( &logger, "\r\n WHITE:" );
for ( uint8_t led_pos = C1X4RGB_LED_POS_LD1; led_pos <= C1X4RGB_LED_POS_LD4; led_pos++ )
{
if ( C1X4RGB_OK == c1x4rgb_set_rgb_color( &c1x4rgb, led_pos, DEMO_COLOR_INT_100,
DEMO_COLOR_INT_100,
DEMO_COLOR_INT_100 ) )
{
log_printf( &logger, " LD%d ", ( uint16_t ) led_pos );
Delay_ms ( 100 );
}
}
}
The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.
Other Mikroe Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.1x4RGB
Additional notes and informations
Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.