forked from vedderb/bldc
-
Notifications
You must be signed in to change notification settings - Fork 0
/
conf_general.h
executable file
·197 lines (164 loc) · 6.95 KB
/
conf_general.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
/*
Copyright 2017 - 2022 Benjamin Vedder [email protected]
This file is part of the VESC firmware.
The VESC firmware is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
The VESC firmware is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef CONF_GENERAL_H_
#define CONF_GENERAL_H_
// Firmware version
#define FW_VERSION_MAJOR 6
#define FW_VERSION_MINOR 05
// Set to 0 for building a release and iterate during beta test builds
#define FW_TEST_VERSION_NUMBER 17
#include "datatypes.h"
// Disable hardware limits on configuration parameters
//#define DISABLE_HW_LIMITS
#if !defined(HW_SOURCE) && !defined(HW_SOURCE_ALT)
#error "No hardware source file set"
#endif
#ifndef HW_HEADER
#error "No hardware header file set"
#endif
#ifdef USER_MC_CONF
#include USER_MC_CONF
#endif
#ifdef USER_APP_CONF
#include USER_APP_CONF
#endif
// This is how to provide a custom UI in VESC Tool. The UI can be created and tested in the
// scripting page, then the source files can be exported. The defines below use the exported
// files to provide the custom UI when VESC Tool connects.
//
// The intention if the HW gui is to be part of the HW-file and the app gui is for custom apps.
// Both can be used at the same time.
//
// Defining QMLUI_HW_FULLSCREEN and/or QMLUI_APP_FULLSCREEN will disable the other pages in the
// mobile version of VESC Tool.
//
//#define QMLUI_SOURCE_HW "qmlui/hw/qmlui_example_hw.c"
//#define QMLUI_HEADER_HW "qmlui/hw/qmlui_example_hw.h"
//#define QMLUI_HW_FULLSCREEN
//
//#define QMLUI_SOURCE_APP "qmlui/app/qmlui_example_app.c"
//#define QMLUI_HEADER_APP "qmlui/app/qmlui_example_app.h"
//#define QMLUI_APP_FULLSCREEN
/*
* Select default user motor configuration
*/
//#include "mcconf_default.h"
//#include "mcconf_china_60kv.h"
/*
* Select default user app configuration
*/
//#include "appconf_example_ppm.h"
//#include "appconf_custom.h"
/*
* Set APP_CUSTOM_TO_USE to the name of the main C file of the custom application.
*/
//#define APP_CUSTOM_TO_USE "app_custom_template.c"
//#define APP_CUSTOM_TO_USE "app_motor_heater.c"
//#include "er/app_erockit_conf_v2.h"
//#include "finn/app_finn_az_conf.h"
#include "hw.h"
#include "mcconf_default.h"
#include "appconf_default.h"
/*
* Enable blackmagic probe output on SWD port
*/
#ifndef HAS_BLACKMAGIC
#define HAS_BLACKMAGIC 1
#endif
/*
* Enable CAN-bus
*/
#ifndef CAN_ENABLE
#define CAN_ENABLE 1
#endif
#ifdef HW_HAS_NO_CAN
#undef CAN_ENABLE
#define CAN_ENABLE 0
#endif
/*
* Servo output driver
*/
#define SERVO_OUT_PULSE_MIN_US 1000 // Minimum pulse length in microseconds
#define SERVO_OUT_PULSE_MAX_US 2000 // Maximum pulse length in microseconds
#define SERVO_OUT_RATE_HZ 50 // Update rate in Hz
// Correction factor for computations that depend on the old resistor division factor
#define VDIV_CORR ((VIN_R2 / (VIN_R2 + VIN_R1)) / (2.2 / (2.2 + 33.0)))
// Current ADC to amperes factor
#define FAC_CURRENT ((V_REG / 4095.0) / (CURRENT_SHUNT_RES * CURRENT_AMP_GAIN))
#define VOLTAGE_TO_ADC_FACTOR ( VIN_R2 / (VIN_R2 + VIN_R1) ) * ( 4096.0 / V_REG )
// Actual voltage on 3.3V net based on internal reference
//#define V_REG (1.21 / ((float)ADC_Value[ADC_IND_VREFINT] / 4095.0))
//#define V_REG 3.3
// Use the pins for the hardware SPI port instead of the hall/encoder pins for the AS5047
#ifndef AS504x_USE_SW_MOSI_PIN
#define AS504x_USE_SW_MOSI_PIN 0
#endif
/*
* MCU
*/
#define SYSTEM_CORE_CLOCK 168000000
#define STM32_UUID ((uint32_t*)0x1FFF7A10)
#define STM32_UUID_8 ((uint8_t*)0x1FFF7A10)
/*
* Run the BLDC speed controller in current mode instead of duty cycle mode. This will
* make it behave like the FOC speed controller. The duty cycle mode has the advantage
* that it does not require the extra current controller since bldc inherently runs
* with duty cycle control. The current controller also outputs a duty cycle in the
* end, and then the speed controller might as well do the same without the current
* controller dynamics in between. FOC on the other hand is inherently based on current
* control.
*/
#define BLDC_SPEED_CONTROL_CURRENT 1
/*
* Run the FOC loop once every N ADC ISR requests. This way the pwm frequency is
* detached from the FOC calculation, which because it takes ~25usec it can't work
* at >40khz. To set a 100kHz pwm FOC_CONTROL_LOOP_FREQ_DIVIDER can be set at 3
* so it skips 2 ISR calls and execute the control loop in the 3rd call.
*/
#ifndef FOC_CONTROL_LOOP_FREQ_DIVIDER
#define FOC_CONTROL_LOOP_FREQ_DIVIDER 1
#endif
// Global configuration variables
extern bool conf_general_permanent_nrf_found;
extern volatile backup_data g_backup;
// Functions
void conf_general_init(void);
bool conf_general_store_backup_data(void);
bool conf_general_read_eeprom_var_hw(eeprom_var *v, int address);
bool conf_general_read_eeprom_var_custom(eeprom_var *v, int address);
bool conf_general_store_eeprom_var_hw(eeprom_var *v, int address);
bool conf_general_store_eeprom_var_custom(eeprom_var *v, int address);
void conf_general_read_app_configuration(app_configuration *conf);
bool conf_general_store_app_configuration(app_configuration *conf);
void conf_general_read_mc_configuration(mc_configuration *conf, bool is_motor_2);
bool conf_general_store_mc_configuration(mc_configuration *conf, bool is_motor_2);
bool conf_general_detect_motor_param(float current, float min_rpm, float low_duty,
float *int_limit, float *bemf_coupling_k, int8_t *hall_table, int *hall_res);
bool conf_general_measure_flux_linkage(float current, float duty,
float min_erpm, float res, float *linkage);
uint8_t conf_general_calculate_deadtime(float deadtime_ns, float core_clock_freq);
int conf_general_measure_flux_linkage_openloop(float current, float duty,
float erpm_per_sec, float res, float ind, float *linkage,
float *linkage_undriven, float *undriven_samples, bool *result);
int conf_general_autodetect_apply_sensors_foc(float current,
bool store_mcconf_on_success, bool send_mcconf_on_success, int *result);
void conf_general_calc_apply_foc_cc_kp_ki_gain(mc_configuration *mcconf, float tc);
int conf_general_detect_apply_all_foc(float max_power_loss,
bool store_mcconf_on_success, bool send_mcconf_on_success);
int conf_general_detect_apply_all_foc_can(bool detect_can, float max_power_loss,
float min_current_in, float max_current_in,
float openloop_rpm, float sl_erpm,
void(*reply_func)(unsigned char* data, unsigned int len));
#endif /* CONF_GENERAL_H_ */