From 74473322e550e8ca1d7a9c513ea3a909b4845126 Mon Sep 17 00:00:00 2001 From: Herb McNew Date: Tue, 14 Nov 2023 13:15:46 -0500 Subject: [PATCH] config: Add Sovol SV06 Plus (#6397) New configuration for the Sovol SV06 Plus Initial pass at adding a printer configuration for the Sovol SV06 Plus based on the existing Sovol SV06 config. Updated for the larger build volume, added filament runout sensor, and removed any references to the LCD screen since the stock screen doesn't work with Klipper. Signed-off-by: Herb McNew --- config/printer-sovol-sv06-plus-2023.cfg | 147 ++++++++++++++++++++++++ test/klippy/printers.test | 1 + 2 files changed, 148 insertions(+) create mode 100644 config/printer-sovol-sv06-plus-2023.cfg diff --git a/config/printer-sovol-sv06-plus-2023.cfg b/config/printer-sovol-sv06-plus-2023.cfg new file mode 100644 index 000000000000..cb6fbd873f9d --- /dev/null +++ b/config/printer-sovol-sv06-plus-2023.cfg @@ -0,0 +1,147 @@ +# This file contains pin mappings for the stock Sovol SV06 Plus +# To use this config, during "make menuconfig" select the +# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication. +# Also, since it is using the GD32F103, please select Disable SWD at startup +# +# Flash this firmware by copying "out/klipper.bin" to a SD card and +# turning on the printer with the card inserted. The firmware +# filename must end in ".bin" and must not match the last filename +# that was flashed. +# +# Note: The stock LCD display does not currently work with Klipper +# +# See docs/Config_Reference.md for a description of parameters. +[mcu] +serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0 +restart_method: command + +[printer] +kinematics: cartesian +max_velocity: 500 +max_accel: 2000 +max_z_velocity: 10 +max_z_accel: 100 + +[stepper_x] +step_pin: PC2 +dir_pin: !PB9 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: tmc2209_stepper_x:virtual_endstop +position_endstop: 0 +position_max: 305 +homing_speed: 40 +homing_retract_dist: 0 + +[tmc2209 stepper_x] +uart_pin: PC1 +run_current: 0.860 +sense_resistor: 0.150 +uart_address: 3 +driver_SGTHRS: 81 +diag_pin: PA5 + +[stepper_y] +step_pin: PB8 +dir_pin: PB7 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: tmc2209_stepper_y:virtual_endstop +position_endstop: 0 +position_max: 305 +homing_speed: 40 +homing_retract_dist: 0 + +[tmc2209 stepper_y] +uart_pin: PC0 +run_current: 0.900 +sense_resistor: 0.150 +uart_address: 3 +driver_SGTHRS: 82 +diag_pin: PA6 + +[stepper_z] +step_pin: PB6 +dir_pin: !PB5 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 4 +endstop_pin: probe:z_virtual_endstop +position_min: -4 +position_max: 350 +homing_speed: 4 + +[tmc2209 stepper_z] +uart_pin: PA15 +run_current: 1.000 +interpolate: False +sense_resistor: 0.150 +uart_address: 3 +diag_pin: PA7 + +[extruder] +max_extrude_only_distance: 100.0 +step_pin: PB4 +dir_pin: !PB3 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 4.56 +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PA1 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC5 +control: pid +pid_kd: 41.96 +pid_kp: 15.66 +pid_ki: 1.49 +min_temp: 0 +max_temp: 300 + +[tmc2209 extruder] +uart_pin: PC14 +run_current: 0.550 +stealthchop_threshold: 0 +interpolate: False +sense_resistor: 0.150 +uart_address: 3 + +[heater_bed] +heater_pin: PA2 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC4 +control: pid +pid_kp: 186.38 +pid_ki: 36.12 +pid_kd: 637.30 +min_temp: 0 +max_temp: 130 + +[fan] +pin: PA0 + +[probe] +pin: PB1 +x_offset: 28 +y_offset: -20 +z_offset: 0 + +[safe_z_home] +home_xy_position: 123,170 +z_hop: 10 +z_hop_speed: 5 + +[bed_mesh] +speed: 120 +mesh_min: 28, 20 +mesh_max: 270, 270 +probe_count: 5 +algorithm: bicubic +fade_end: 10 +fade_target: 0 + +[filament_switch_sensor filament_runout_sensor] +switch_pin: PA4 +pause_on_runout: True diff --git a/test/klippy/printers.test b/test/klippy/printers.test index d9168adc58e7..2ab96acc85e3 100644 --- a/test/klippy/printers.test +++ b/test/klippy/printers.test @@ -157,6 +157,7 @@ CONFIG ../../config/printer-anycubic-vyper-2021.cfg CONFIG ../../config/printer-monoprice-select-mini-v1-2016.cfg CONFIG ../../config/printer-sovol-sv05-2022.cfg CONFIG ../../config/printer-sovol-sv06-2022.cfg +CONFIG ../../config/printer-sovol-sv06-plus-2023.cfg CONFIG ../../config/printer-sunlu-t3-2022.cfg # Printers using the stm32f103 via serial