msm-pmi8940.dtsi

/*
 * Copyright (c) 2016-2017, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

#include <dt-bindings/msm/power-on.h>

&spmi_bus {

	qcom,pmi8940@2 {
		spmi-slave-container;
		reg = <0x2>;
		#address-cells = <1>;
		#size-cells = <1>;

		pmi8940_revid: qcom,revid@100 {
			compatible = "qcom,qpnp-revid";
			reg = <0x100 0x100>;
		};

		qcom,power-on@800 {
			compatible = "qcom,qpnp-power-on";
			reg = <0x800 0x100>;
			qcom,secondary-pon-reset;
			qcom,hard-reset-poweroff-type =
				<PON_POWER_OFF_SHUTDOWN>;

			pon_perph_reg: qcom,pon_perph_reg {
				regulator-name = "pon_spare_reg";
				qcom,pon-spare-reg-addr = <0x8c>;
				qcom,pon-spare-reg-bit = <1>;
			};
		};

		pmi8940_vadc: vadc@3100 {
			compatible = "qcom,qpnp-vadc";
			reg = <0x3100 0x100>;
			#address-cells = <1>;
			#size-cells = <0>;
			interrupts = <0x2 0x31 0x0>;
			interrupt-names = "eoc-int-en-set";
			qcom,adc-bit-resolution = <15>;
			qcom,adc-vdd-reference = <1800>;
			qcom,vadc-poll-eoc;

			chan@0 {
				label = "usbin";
				reg = <0>;
				qcom,decimation = <0>;
				qcom,pre-div-channel-scaling = <4>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
			};

			chan@1 {
				label = "dcin";
				reg = <1>;
				qcom,decimation = <0>;
				qcom,pre-div-channel-scaling = <4>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
			};

			chan@3 {
				label = "vchg_sns";
				reg = <3>;
				qcom,decimation = <0>;
				qcom,pre-div-channel-scaling = <1>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
			};

			chan@9 {
				label = "ref_625mv";
				reg = <9>;
				qcom,decimation = <0>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
			};

			chan@a {
				label = "ref_1250v";
				reg = <0xa>;
				qcom,decimation = <0>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
			};

			chan@d {
				label = "chg_temp";
				reg = <0xd>;
				qcom,decimation = <0>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <16>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
			};

			chan@43 {
				label = "usb_dp";
				reg = <0x43>;
				qcom,decimation = <0>;
				qcom,pre-div-channel-scaling = <1>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
			};

			chan@44 {
				label = "usb_dm";
				reg = <0x44>;
				qcom,decimation = <0>;
				qcom,pre-div-channel-scaling = <1>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
			};
		};

		pmi8940_mpps: mpps {
			spmi-dev-container;
			compatible = "qcom,qpnp-pin";
			gpio-controller;
			#gpio-cells = <2>;
			#address-cells = <1>;
			#size-cells = <1>;
			label = "pmi8940-mpp";

			mpp@a000 {
				reg = <0xa000 0x100>;
				qcom,pin-num = <1>;
				status = "disabled";
			};

			mpp@a100 {
				reg = <0xa100 0x100>;
				qcom,pin-num = <2>;
				status = "disabled";
			};

			mpp@a300 {
				reg = <0xa300 0x100>;
				qcom,pin-num = <4>;
				status = "disabled";
			};
		};

		pmi8940_charger: qcom,qpnp-smbcharger {
			spmi-dev-container;
			compatible = "qcom,qpnp-smbcharger";
			#address-cells = <1>;
			#size-cells = <1>;

			qcom,usbin-vadc = <&pmi8940_vadc>;     // pony.ma, DATE20171214, add input voltage log, DATE20171214-01 LINE
			qcom,float-voltage-mv = <4400>;
			// pony.ma, DATE20171010, Define project battery capacity for 3rd apk, DATE20171010-01 LINE
			qcom,tinno-battery-capacity = <3900>;
			qcom,weak-charger-enable = <1>;
			qcom,resume-delta-mv = <200>;
			qcom,fastchg-current-ma = <1800>;		    
			qcom,chg-inhibit-fg;
			qcom,rparasitic-uohm = <100000>;
			qcom,bms-psy-name = "bms";
			qcom,thermal-mitigation = <1800 1200 1000 0>;
			qcom,pmic-revid = <&pmi8940_revid>;
			qcom,force-aicl-rerun;
			qcom,aicl-rerun-period-s = <180>;
			qcom,float-voltage-comp = <16>;
			qcom,fastchg-current-comp = <700>; //700ma
			qcom,fastchg-current-comp-warm = <1200>;
			//LINE<REQ><><DEFUALT USB DCP ICL SET TO 1400MA><20160708>huiyong.yin
			qcom,no-parallel-defualt-dcp-icl-ma = <1800>;
			qcom,no_support_qc;//<20160720><don't support qc>wangyanhui add 
			// pony.ma, DATE20160902, HCADCNA-317, insert SDP and restart, do not set usb il, DATE20160902-01 LINE
			qcom,override-usb-current;
			qcom,speed-current = <1800 1400 1200 1100 900 700 600 450 400 0>;


			qcom,chgr@1000 {
				reg = <0x1000 0x100>;
				interrupts =	<0x2 0x10 0x0>,
						<0x2 0x10 0x1>,
						<0x2 0x10 0x2>,
						<0x2 0x10 0x3>,
						<0x2 0x10 0x4>,
						<0x2 0x10 0x5>,
						<0x2 0x10 0x6>,
						<0x2 0x10 0x7>;

				interrupt-names =	"chg-error",
							"chg-inhibit",
							"chg-prechg-sft",
							"chg-complete-chg-sft",
							"chg-p2f-thr",
							"chg-rechg-thr",
							"chg-taper-thr",
							"chg-tcc-thr";
			};

			qcom,otg@1100 {
				reg = <0x1100 0x100>;
				interrupts =	<0x2 0x11 0x0>,
						<0x2 0x11 0x1>,
						<0x2 0x11 0x3>;
				interrupt-names =	"otg-fail",
							"otg-oc",
						"usbid-change";
			};

			qcom,bat-if@1200 {
				reg = <0x1200 0x100>;
				interrupts =	<0x2 0x12 0x0>,
						<0x2 0x12 0x1>,
						<0x2 0x12 0x2>,
						<0x2 0x12 0x3>,
					<0x2 0x12 0x4>,
						<0x2 0x12 0x5>,
						<0x2 0x12 0x6>,
						<0x2 0x12 0x7>;

				interrupt-names =	"batt-hot",
							"batt-warm",
							"batt-cold",
							"batt-cool",
						"batt-ov",
							"batt-low",
							"batt-missing",
							"batt-term-missing";
			};

			qcom,usb-chgpth@1300 {
				reg = <0x1300 0x100>;
				interrupts =	<0x2 0x13 0x0>,
						<0x2 0x13 0x1>,
					<0x2 0x13 0x2>,
						<0x2 0x13 0x5>;

				interrupt-names =	"usbin-uv",
						"usbin-ov",
							"usbin-src-det",
							"aicl-done";
			};

			qcom,dc-chgpth@1400 {
				reg = <0x1400 0x100>;
				interrupts =	<0x2 0x14 0x0>,
						<0x2 0x14 0x1>;
				interrupt-names =	"dcin-uv",
							"dcin-ov";
			};

			qcom,chgr-misc@1600 {
				reg = <0x1600 0x100>;
				interrupts =	<0x2 0x16 0x0>,
						<0x2 0x16 0x1>,
						<0x2 0x16 0x2>,
					<0x2 0x16 0x3>,
						<0x2 0x16 0x4>,
						<0x2 0x16 0x5>;

				interrupt-names =	"power-ok",
							"temp-shutdown",
							"wdog-timeout",
							"flash-fail",
							"otst2",
							"otst3";
			};

			smbcharger_charger_otg: qcom,smbcharger-boost-otg {
				regulator-name = "smbcharger_charger_otg";
			};
		};

		pmi8940_fg: qcom,fg {
			spmi-dev-container;
			compatible = "qcom,qpnp-fg";
			#address-cells = <1>;
			#size-cells = <1>;
			qcom,fg-cc-cv-threshold-mv = <4390>;          //---pony
			qcom,vbat-estimate-diff-mv =<200>;            //VCIFGCE-367 resolve soc inaccurate
			qcom,resume-soc = <95>;
			status = "okay";
			qcom,bcl-lm-threshold-ma = <127>;
			qcom,bcl-mh-threshold-ma = <405>;
			qcom,fg-iterm-ma = <200>;
			qcom,fg-chg-iterm-ma = <150>;
			qcom,pmic-revid = <&pmi8940_revid>;
			qcom,fg-cutoff-voltage-mv = <3400>;
			qcom,cycle-counter-en;
			qcom,ext-sense-type;
			qcom,cold-hot-jeita-hysteresis = <0 0>;//add by lijian

//Battery NTC is 3435K ,But we choose 3440K,becuse Tinno's test method  is not rigorous.
//NTC            C1                C2              C3
//b3440 -3.3802  86C2  0.036987   50BB -0.00381  37CF
			qcom,thermal-coefficients =[c2 86 bb 50 cf 37];
			qcom,capacity-learning-on;
			qcom,hold-soc-while-full;
			qcom,fg-soc@4000 {
			status = "okay";
				reg = <0x4000 0x100>;
				interrupts =	<0x2 0x40 0x0>,
						<0x2 0x40 0x1>,
						<0x2 0x40 0x2>,
						<0x2 0x40 0x3>,
						<0x2 0x40 0x4>,
						<0x2 0x40 0x5>,
						<0x2 0x40 0x6>;

				interrupt-names =	"high-soc",
							"low-soc",
							"full-soc",
							"empty-soc",
							"delta-soc",
							"first-est-done",
							"update-soc";
			};

			qcom,fg-batt@4100 {
				reg = <0x4100 0x100>;
				interrupts =	<0x2 0x41 0x0>,
						<0x2 0x41 0x1>,
					<0x2 0x41 0x2>,
						<0x2 0x41 0x3>,
						<0x2 0x41 0x4>,
						<0x2 0x41 0x5>,
						<0x2 0x41 0x6>,
						<0x2 0x41 0x7>;

				interrupt-names =	"soft-cold",
							"soft-hot",
							"vbatt-low",
							"batt-ided",
							"batt-id-req",
							"batt-unknown",
							"batt-missing",
							"batt-match";
			};

			qcom,revid-tp-rev@1f1 {
				reg = <0x1f1 0x1>;
			};

			qcom,fg-memif@4400 {
				status = "okay";
				reg = <0x4400 0x100>;
				interrupts =	<0x2 0x44 0x0>,
						<0x2 0x44 0x2>;

				interrupt-names =	"mem-avail",
							"data-rcvry-sug";
			};
		};

		bcl@4200 {
			compatible = "qcom,msm-bcl";
			reg = <0x4200 0xff>;
			reg-names = "fg_user_adc";
			interrupts = <0x2 0x42 0x0>,
					<0x2 0x42 0x1>;
			interrupt-names = "bcl-high-ibat-int",
					"bcl-low-vbat-int";
			qcom,vbat-scaling-factor = <39000>;
			qcom,vbat-gain-numerator = <1>;
			qcom,vbat-gain-denominator = <128>;
			qcom,vbat-polling-delay-ms = <100>;
			qcom,ibat-scaling-factor = <39000>;
			qcom,ibat-gain-numerator = <1>;
			qcom,ibat-gain-denominator = <128>;
			qcom,ibat-offset-numerator = <1200>;
			qcom,ibat-offset-denominator = <1>;
			qcom,ibat-polling-delay-ms = <100>;
		};

// pony.ma, DATE20170222, pwm mode config for green blink, DATE20170222-01 START
		qcom,leds@a100 {
			compatible = "qcom,leds-qpnp";
			reg = <0xa100 0x100>;
                        status = "okay";
                        qcom,led_mpp_2 {
			label = "mpp";
                        linux,name = "green"; 
                        linux,default-trigger = "none"; 
                        qcom,default-state = "off"; 
                        qcom,max-current = <40>; 
                        qcom,current-setting = <10>; 
                        qcom,id = <6>; 
                        qcom,mode = "pwm"; 
                        qcom,source-sel = <8>; 
                        qcom,mode-ctrl = <0x60>; 
                        qcom,pwm-channel = <0>;
			qcom,pwm-us = <5000000>;
                        pwms = <&pmi8940_pwm 0 0>; 
                        pwm-names="green"; // add this
			qcom,use-blink;
                                         };
		};
// pony.ma, DATE20170222-01 END
	};

	qcom,pmi8940@3 {
		spmi-slave-container;
		reg = <0x3>;
		#address-cells = <1>;
		#size-cells = <1>;
		status = "okay"; 
		pmi8940_pwm: pwm@b000 {
			compatible = "qcom,qpnp-pwm";
			reg = <0xb000 0x100>;
			reg-names = "qpnp-lpg-channel-base";
			qcom,channel-id = <0>;
			qcom,supported-sizes = <6>, <9>;
			qcom,period = <1000000>;
                        qcom,dtest-line = <1>; 
                        qcom,dtest-output = <1>; 
			#pwm-cells = <2>;
                        qcom,pwm { 
				qcom,duty = <500000>; //PWM duty time in microseconds
                        label = "pwm"; 
                        }; 
		};

		labibb: qpnp-labibb-regulator {
			status = "disabled";
			spmi-dev-container;
			compatible = "qcom,qpnp-labibb-regulator";
			#address-cells = <1>;
			#size-cells = <1>;
			qcom,pmic-revid = <&pmi8940_revid>;

			ibb_regulator: qcom,ibb@dc00 {
				reg = <0xdc00 0x100>;
				reg-names = "ibb_reg";
				regulator-name = "ibb_reg";

				regulator-min-microvolt = <4600000>;
				regulator-max-microvolt = <6000000>;

				qcom,qpnp-ibb-min-voltage = <1400000>;
				qcom,qpnp-ibb-step-size = <100000>;
				qcom,qpnp-ibb-slew-rate = <2000000>;
				qcom,qpnp-ibb-use-default-voltage;
				qcom,qpnp-ibb-init-voltage = <5500000>;
				qcom,qpnp-ibb-init-amoled-voltage = <4000000>;
				qcom,qpnp-ibb-init-lcd-voltage = <5500000>;

				qcom,qpnp-ibb-soft-start = <1000>;

				qcom,qpnp-ibb-discharge-resistor = <32>;
				qcom,qpnp-ibb-lab-pwrup-delay = <8000>;
				qcom,qpnp-ibb-lab-pwrdn-delay = <8000>;
				qcom,qpnp-ibb-en-discharge;

				qcom,qpnp-ibb-full-pull-down;
				qcom,qpnp-ibb-pull-down-enable;
				qcom,qpnp-ibb-switching-clock-frequency =
									<1480>;
				qcom,qpnp-ibb-limit-maximum-current = <1550>;
				qcom,qpnp-ibb-debounce-cycle = <16>;
				qcom,qpnp-ibb-limit-max-current-enable;
				qcom,qpnp-ibb-ps-enable;
			};

			lab_regulator: qcom,lab@de00 {
				reg = <0xde00 0x100>;
				reg-names = "lab";
				regulator-name = "lab_reg";

				regulator-min-microvolt = <4600000>;
				regulator-max-microvolt = <6000000>;

				qcom,qpnp-lab-min-voltage = <4600000>;
				qcom,qpnp-lab-step-size = <100000>;
				qcom,qpnp-lab-slew-rate = <5000>;
				qcom,qpnp-lab-use-default-voltage;
				qcom,qpnp-lab-init-voltage = <5500000>;
				qcom,qpnp-lab-init-amoled-voltage = <4600000>;
				qcom,qpnp-lab-init-lcd-voltage = <5500000>;

				qcom,qpnp-lab-soft-start = <800>;

				qcom,qpnp-lab-full-pull-down;
				qcom,qpnp-lab-pull-down-enable;
				qcom,qpnp-lab-switching-clock-frequency =
									<1600>;
				qcom,qpnp-lab-limit-maximum-current = <800>;
				qcom,qpnp-lab-limit-max-current-enable;
				qcom,qpnp-lab-ps-threshold = <40>;
				qcom,qpnp-lab-ps-enable;
				qcom,qpnp-lab-nfet-size = <100>;
				qcom,qpnp-lab-pfet-size = <100>;
				qcom,qpnp-lab-max-precharge-time = <500>;
			};
		};

		wled: qcom,leds@d800 {
			compatible = "qcom,qpnp-wled";
			reg = <0xd800 0x100>,
				<0xd900 0x100>;
			reg-names = "qpnp-wled-ctrl-base",
					"qpnp-wled-sink-base";
			interrupts = <0x3 0xd8 0x2>;
			interrupt-names = "sc-irq";
			status = "okay";
			linux,name = "wled";
			linux,default-trigger = "bkl-trigger";
			qcom,fdbk-output = "auto";
			qcom,vref-mv = <350>;
			qcom,switch-freq-khz = <800>;
			qcom,ovp-mv = <29500>;
			qcom,ilim-ma = <980>;
			qcom,boost-duty-ns = <26>;
			qcom,mod-freq-khz = <9600>;
			qcom,dim-mode = "hybrid";
			qcom,dim-method = "linear";
			qcom,hyb-thres = <625>;
			qcom,sync-dly-us = <800>;
			qcom,fs-curr-ua = <20000>;
			qcom,en-phase-stag;
			qcom,led-strings-list = [00 01];
// pony.ma, DATE20170222, pwm mode config for green blink, DATE20170222-01 LINE
			//qcom,en-ext-pfet-sc-pro;
			qcom,cons-sync-write-delay-us = <1000>;
		};

		flash_led: qcom,leds@d300 {
			compatible = "qcom,qpnp-flash-led";
			status = "okay";
			reg = <0xd300 0x100>;
			label = "flash";
			qcom,headroom = <500>;
			qcom,startup-dly = <128>;
			qcom,clamp-curr = <200>;
			qcom,pmic-charger-support;
			qcom,self-check-enabled;
			qcom,thermal-derate-enabled;
			qcom,thermal-derate-threshold = <100>;
			qcom,thermal-derate-rate = "5_PERCENT";
			qcom,current-ramp-enabled;
			qcom,ramp_up_step = "6P7_US";
			qcom,ramp_dn_step = "6P7_US";
			qcom,vph-pwr-droop-enabled;
			qcom,vph-pwr-droop-threshold = <3000>;
			qcom,vph-pwr-droop-debounce-time = <10>;
			qcom,headroom-sense-ch0-enabled;
			qcom,headroom-sense-ch1-enabled;
			qcom,pmic-revid = <&pmi8940_revid>;

			pmi8940_flash0: qcom,flash_0 {
				label = "flash";
				qcom,led-name = "led:flash_0";
				qcom,default-led-trigger =
						"flash0_trigger";
				qcom,max-current = <1000>;
				qcom,duration = <1280>;
				qcom,id = <0>;
				qcom,current = <625>;
			};

			pmi8940_flash1: qcom,flash_1 {
				label = "flash";
				qcom,led-name = "led:flash_1";
				qcom,default-led-trigger =
						"flash1_trigger";
				qcom,max-current = <1000>;
				qcom,duration = <1280>;
				qcom,id = <1>;
				qcom,current = <625>;
			};

			pmi8940_torch0: qcom,torch_0 {
				label = "torch";
				qcom,led-name = "led:torch_0";
				qcom,default-led-trigger =
						"torch0_trigger";
				qcom,max-current = <200>;
				qcom,id = <0>;
				qcom,current = <120>;
			};

			pmi8940_torch1: qcom,torch_1 {
				label = "torch";
				qcom,led-name = "led:torch_1";
				qcom,default-led-trigger =
						"torch1_trigger";
				qcom,max-current = <200>;
				qcom,id = <1>;
				qcom,current = <120>;
			};

			pmi8940_switch: qcom,switch {
				label = "switch";
				qcom,led-name = "led:switch";
				qcom,default-led-trigger =
						"switch_trigger";
				qcom,max-current = <1000>;
				qcom,duration = <1280>;
				qcom,id = <2>;
				qcom,current = <625>;
				reg0 {
					regulator-name = "pon_spare_reg";
				};
			};
		};

		pmi_haptic: qcom,haptic@c000 {
			compatible = "qcom,qpnp-haptic";
			reg = <0xc000 0x100>;
			interrupts = <0x3 0xc0 0x0>,
				<0x3 0xc0 0x1>;
			interrupt-names = "sc-irq", "play-irq";
			qcom,pmic-revid = <&pmi8940_revid>;
			vcc_pon-supply = <&pon_perph_reg>;
			qcom,play-mode = "direct";
			qcom,wave-play-rate-us = <4165>;
			qcom,actuator-type = "erm";
			qcom,wave-shape = "square";
			qcom,vmax-mv = <3000>;
			qcom,ilim-ma = <800>;
			qcom,sc-deb-cycles = <8>;
			qcom,int-pwm-freq-khz = <505>;
			qcom,en-brake;
			qcom,brake-pattern = [03 03 00 00];
			qcom,use-play-irq;
			qcom,use-sc-irq;
			qcom,wave-samples = [3e 3e 3e 3e 3e 3e 3e 3e];
			qcom,wave-rep-cnt = <1>;
			qcom,wave-samp-rep-cnt = <1>;
			//qcom,lra-auto-res-mode="qwd";
			//qcom,lra-high-z="opt1";
			//qcom,lra-res-cal-period = <4>;
			//qcom,correct-lra-drive-freq;
			//qcom,misc-trim-error-rc19p2-clk-reg-present;
		};
	};
};