forked from hjd1964/OnStep
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Config.h
245 lines (204 loc) · 24.4 KB
/
Config.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
// ---------------------------------------------------------------------------------------------------------------------------------
// Configuration for OnStep
/*
* For more information on setting OnStep up see http://www.stellarjourney.com/index.php?r=site/equipment_onstep
* and join the OnStep Groups.io at https://groups.io/g/onstep
*
* *** Read the compiler warnings and errors, they are there to help guard against invalid configurations ***
*/
// ---------------------------------------------------------------------------------------------------------------------------------
// ADJUST THE FOLLOWING TO CONFIGURE YOUR CONTROLLER FEATURES ----------------------------------------------------------------------
// <-Req'd = always must set, <-Often = usually must set, Option = optional, Adjust = adjust as req'd, Infreq = infrequently changed
// PINMAP ---------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#PINMAP
// *** See the matching Pins.xxx.h file for your setup (found by looking in src/pinmaps/Models.h) with detailed information ***
// *** to be sure it matches your wiring. *** USE AT YOUR OWN RISK *** ***
// Parameter Name Value Default Notes Hint
#define PINMAP OFF // OFF, Choose from: MiniPCB, MiniPCB2, MaxPCB, MaxPCB2, STM32Blue, <-Req'd
// Ramps14, MaxESP2, MaxESP3. Check Constants.h for more info.
// SERIAL PORT COMMAND CHANNELS ------------------------------------ see https://onstep.groups.io/g/main/wiki/6-Configuration#SERIAL
#define SERIAL_A_BAUD_DEFAULT 9600 // 9600, n. Where n=9600,19200,57600,115200 (common baud rates.) Infreq
#define SERIAL_B_BAUD_DEFAULT 9600 // 9600, n. See (src/HAL/) for your MCU Serial port # etc. Option
#define SERIAL_B_ESP_FLASHING OFF // OFF, ON Upload ESP8266 WiFi firmware through SERIAL_B with :ESPFLASH# cmd. Option
#define SERIAL_C_BAUD_DEFAULT OFF // OFF, n, ON for ESP32 Bluetooth. Option
#define SERIAL_C_BLUETOOTH_NAME "OnStep" // "On..", Bluetooth device name for ESP32. Option
// MOUNT TYPE -------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#MOUNT_TYPE
#define MOUNT_TYPE GEM // GEM, GEM for German Equatorial, FORK for Equatorial Fork, or ALTAZM <-Req'd
// Dobsonian etc. mounts. GEM Eq mounts perform meridian flips.
// USER FEEDBACK -------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#USER_FEEDBACK
#define LED_STATUS ON // ON, Blinks w/sidereal tracking otherwise steady on indicates activity. Option
#define LED_STATUS2 OFF // OFF, ON Blinks 1s interval w/PPS sync, steady for gotos, off if in standby. Option
#define LED_RETICLE OFF // OFF, n. Where n=0..255 (0..100%) activates feature sets default brightness. Option
#define BUZZER OFF // OFF, ON, n. Where n=100..6000 (Hz freq.) for piezo speaker. ON for buzzer. Option
#define BUZZER_STATE_DEFAULT OFF // OFF, ON Start with piezo buzzer/speaker enabled. Option
// TIME AND LOCATION -------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#TLS
#define TIME_LOCATION_SOURCE OFF // OFF, DS3231 (I2c,) DS3234 (Spi,) TEENSY (T3.2 internal,) or GPS source. Option
// Provides Date/Time, and if available, PPS & Lat/Long also.
// SENSORS -------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#SENSORS
// * = also supports ON_PULLUP or ON_PULLDOWN to activate MCU internal resistors if present.
#define WEATHER OFF // OFF, BME280 (I2C 0x77,) BME280_0x76, BME280_SPI (see pinmap for CS.) Option
// BMP280 (I2C 0x77,) BMP280_0x76, BMP280_SPI (see pinmap for CS.)
// BME280 or BMP280 for temperature, pressure. BME280 for humidity also.
#define TELESCOPE_TEMPERATURE OFF // OFF, DS1820, n. Where n is the DS1820 s/n for focuser temperature. Adjust
#define HOME_SENSE OFF // OFF, ON*. Automatically detect and use home switches. For GEM mode only. Option
#define HOME_SENSE_STATE_AXIS1 HIGH // HIGH, State when clockwise of home position, as seen from front. Rev. w/LOW. Adjust
#define HOME_SENSE_STATE_AXIS2 HIGH // HIGH, State when clockwise of home position, as seen from above. Rev. w/LOW. Adjust
// Signal state reverses when travel moves ccw past the home position.
#define LIMIT_SENSE OFF // OFF, ON* limit sense switch close to Gnd stops gotos and/or tracking. Option
#define LIMIT_SENSE_STATE LOW // LOW, For NO (normally open) switches, HIGH for NC (normally closed.) Adjust
#define PEC_SENSE OFF // OFF, ON*, n, sense digital OR n=0 to 1023 (0 to 3.3V or 5V) analog threshold. Option
#define PEC_SENSE_STATE HIGH // HIGH, Senses the PEC signal rising edge or use LOW for falling edge. Adjust
// Ignored in ALTAZM mode.
#define PPS_SENSE OFF // OFF, ON* enables PPS (pulse per second,) senses signal rising edge. Option
// Better tracking accuracy especially for Mega2560's w/ceramic resonator.
// ST4 INTERFACE ------------------------------------------------------ see https://onstep.groups.io/g/main/wiki/6-Configuration#ST4
// *** It is up to you to verify the interface meets the electrical specifications of any connected device, use at your own risk ***
#define ST4_INTERFACE OFF // OFF, ON, ON_PULLUP enables interface. <= 1X guides unless hand control mode. Option
// During goto btn press: aborts slew or continue meridian flip pause home
#define ST4_HAND_CONTROL OFF // OFF, ON for hand controller special features and SHC support. Option
// Hold [E]+[W] btns >2s: Guide rate [E]- [W]+ [N] trk on/off [S] sync
// Hold [N]+[S] btns >2s: Usr cat item [E]- [W]+ [N] goto [S] snd on/off
#define ST4_HAND_CONTROL_FOCUSER OFF // OFF, ON alternate to above: Focuser move [E]f1 [W]f2 [N]- [S]+ Option
// GUIDING BEHAVIOUR ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#GUIDING
#define GUIDE_TIME_LIMIT 0 // 0, No guide time limit. Or n. Where n=1..120 second time limit guard. Adjust
#define GUIDE_DISABLE_BACKLASH OFF // OFF, Disable backlash takeup during guiding at <= 1X Option
// TRACKING BEHAVIOUR -------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#TRACKING
#define TRACK_AUTOSTART OFF // OFF, ON Start with tracking enabled. Option
#define TRACK_REFRACTION_RATE_DEFAULT OFF // OFF, ON Start w/atmospheric refract. compensation (RA axis/Eq mounts only.) Option
#define TRACK_BACKLASH_RATE 25 // 25, n. Where n=2..50 (x sidereal rate) during backlash takeup. Option
// Too fast motors stall/gears slam or too slow and sluggish in backlash.
// SYNCING BEHAVIOUR ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#SYNCING
#define SYNC_CURRENT_PIER_SIDE_ONLY ON // ON, Disables ability of sync to change pier side, for GEM mounts. Option
// SLEWING BEHAVIOUR ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#SLEWING
#define SLEW_RATE_BASE_DESIRED 1.0 // 1.0, n. Desired slew rate in deg/sec. Adjustable at run-time from <-Req'd
// 1/2 to 2x this rate, and as MCU performace considerations require.
#define SLEW_RATE_MEMORY OFF // OFF, ON Remembers rates set across power cycles. Option
#define SLEW_ACCELERATION_DIST 5.0 // 5.0, n, (degrees.) Approx. distance for acceleration (and deceleration.) Adjust
#define SLEW_RAPID_STOP_DIST 2.5 // 2.0, n, (degrees.) Approx. distance required to stop when a slew Adjust
// is aborted or a limit is exceeded.
#define MFLIP_SKIP_HOME OFF // OFF, ON Goto directly to the destination without visiting home position. Option
#define MFLIP_PAUSE_HOME_MEMORY OFF // OFF, ON Remember meridian flip pause at home setting across power cycles. Option
#define MFLIP_AUTOMATIC_MEMORY OFF // OFF, ON Remember automatic meridian flip setting across power cycles. Option
// PARKING BEHAVIOUR ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#PARKING
#define STRICT_PARKING OFF // OFF, ON Un-parking is only allowed if successfully parked. Option
// MOTION CONTROL -------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#MOTION
#define STEP_WAVE_FORM SQUARE // SQUARE, PULSE Step signal wave form faster rates. SQUARE best signal integrity. Adjust
// Stepper driver models (also see ~/OnStep/src/sd_drivers/Models.h for additional infrequently used models and more info.):
// A4988, DRV8825, LV8729, S109, SSS TMC2209*, TMC2130* **, and TMC5160* ***
// * = add _QUIET (stealthChop tracking) for example "TMC2130_QUIET"
// ** = SSS TMC2130 if you choose to set stepper driver current (in mA) set Vref pot. 2.5V instead of by motor current as usual.
// *** = SSS TMC5160 you must set stepper driver current (in mA) w/ #define AXISn_TMC_IRUN (IHOLD, etc.)
// AXIS1 RA/AZM
// see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS1
#define AXIS1_STEPS_PER_DEGREE 12800.0 // 12800, n. Number of steps per degree: <-Req'd
// n = (stepper_steps * micro_steps * overall_gear_reduction)/360.0
#define AXIS1_STEPS_PER_WORMROT 0 // 0, n. Number steps per worm rotation (PEC Eq mode only, 0 disables PEC.) <-Req'd
// n = (AXIS1_STEPS_PER_DEGREE*360)/reduction_final_stage
#define AXIS1_DRIVER_MODEL OFF // OFF, (See above.) Stepper driver model. <-Often
#define AXIS1_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. <-Often
#define AXIS1_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during gotos. Option
#define AXIS1_DRIVER_IHOLD OFF // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option
#define AXIS1_DRIVER_IRUN OFF // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option
#define AXIS1_DRIVER_IGOTO OFF // OFF, n, (mA.) Current during slews. OFF uses same as IRUN. Option
#define AXIS1_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. <-Often
#define AXIS1_DRIVER_STATUS OFF // OFF, TMC_SPI, HIGH, or LOW. Polling for driver status info/fault detection. Option
#define AXIS1_LIMIT_MIN -180 // -180, n. Where n= -90..-270 (degrees.) Minimum "Hour Angle" for Eq modes. Adjust
// n. Where n=-180..-360 (degrees.) Minimum Azimuth for AltAzm mode.
#define AXIS1_LIMIT_MAX 180 // 180, n. Where n= 90.. 270 (degrees.) Maximum "Hour Angle" for Eq modes. Adjust
// n. Where n= 180.. 360 (degrees.) Maximum Azimuth for AltAzm mode.
// AXIS2 DEC/ALT
// see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS2
#define AXIS2_STEPS_PER_DEGREE 12800.0 // 12800, n. Number of steps per degree: <-Req'd
// n = (stepper_steps * micro_steps * overall_gear_reduction)/360.0
#define AXIS2_DRIVER_MODEL OFF // OFF, (See above.) Stepper driver model. <-Often
#define AXIS2_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. <-Often
#define AXIS2_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during gotos. Option
#define AXIS2_DRIVER_IHOLD OFF // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option
#define AXIS2_DRIVER_IRUN OFF // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option
#define AXIS2_DRIVER_IGOTO OFF // OFF, n, (mA.) Current during slews. OFF uses same as IRUN. Option
#define AXIS2_DRIVER_POWER_DOWN OFF // OFF, ON Powers off 10sec after movement stops or 10min after last<=1x guide. Option
#define AXIS2_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. <-Often
#define AXIS2_DRIVER_STATUS OFF // OFF, TMC_SPI, HIGH, or LOW. Polling for driver status info/fault detection. Option
#define AXIS2_TANGENT_ARM OFF // OFF, ON +limit range below. Set cntr w/[Reset Home] Return cntr w/[Find Home] Infreq
#define AXIS2_LIMIT_MIN -90 // -90, n. Where n=-90..0 (degrees.) Minimum allowed declination. Infreq
#define AXIS2_LIMIT_MAX 90 // 90, n. Where n=0..90 (degrees.) Maximum allowed declination. Infreq
// AXIS3 ROTATOR
// see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS3
#define ROTATOR OFF // OFF, ON to enable the rotator (or de-rotator for ALTAZM mounts.) Option
#define AXIS3_STEPS_PER_DEGREE 64.0 // 64.0, n. Number of steps per degree for rotator/de-rotator. Adjust
// Alt/Az de-rotation: n = (num_circumference_pixels * 2)/360, minimum
#define AXIS3_SLEW_RATE_DESIRED 1.0 // 1.0, n, (degrees/second) Maximum speed depends on processor. Adjust
#define AXIS3_DRIVER_MODEL OFF // OFF, TMC2130, TMC5160. Leave OFF for all drivers models except these. Option
#define AXIS3_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. For TMC2130, TMC5160. Option
#define AXIS3_DRIVER_IHOLD OFF // OFF, n, (mA.) Current standstill. OFF uses IRUN/2.0. " Option
#define AXIS3_DRIVER_IRUN OFF // OFF, n, (mA.) Current tracking, appropriate for stepper/driver/etc. " Option
#define AXIS3_DRIVER_POWER_DOWN OFF // OFF, ON Powers off the motor at stand-still. Option
#define AXIS3_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option
#define AXIS3_LIMIT_MIN -180 // -180, n. Where n=-360..0 (degrees.) Minimum allowed rotator angle. Infreq
#define AXIS3_LIMIT_MAX 180 // 180, n. Where n=0..360 (degrees.) Maximum allowed rotator angle. Infreq
// AXIS4 FOCUSER 1
// see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS4
#define FOCUSER1 OFF // OFF, ON to enable this focuser. Option
#define AXIS4_STEPS_PER_MICRON 0.5 // 0.5, n. Steps per micrometer. Figure this out by testing or other means. Adjust
#define AXIS4_SLEW_RATE_DESIRED 500 // 500, n, Where n=200..5000 (um/s.) Max microns/second. In DC mode, max pwr % Adjust
#define AXIS4_DRIVER_MODEL OFF // OFF, TMC2130, TMC5160. Leave OFF for all drivers models except these. Option
#define AXIS4_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. For TMC2130, TMC5160. Option
#define AXIS4_DRIVER_IHOLD OFF // OFF, n, (mA.) Current standstill. OFF uses IRUN/2.0. " Option
#define AXIS4_DRIVER_IRUN OFF // OFF, n, (mA.) Current tracking, appropriate for stepper/driver/etc. " Option
#define AXIS4_DRIVER_POWER_DOWN OFF // OFF, ON Powers off the motor at stand-still. Option
#define AXIS4_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option
#define AXIS4_DRIVER_DC_MODE OFF // OFF, DRV8825 for pwm dc motor control on stepper driver outputs. Option
#define AXIS4_LIMIT_MIN_RATE 50 // 50, n. Where n=1..1000 (um/s.) Minimum microns/second. In DC mode, min pwr. Adjust
#define AXIS4_LIMIT_MIN 0 // 0, n. Where n=0..500 (millimeters.) Minimum allowed position. Adjust
#define AXIS4_LIMIT_MAX 50 // 50, n. Where n=0..500 (millimeters.) Maximum allowed position. Adjust
// AXIS5 FOCUSER 2
// see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS5
#define FOCUSER2 OFF // OFF, ON to enable this focuser. Option
#define AXIS5_STEPS_PER_MICRON 0.5 // 0.5, n. Steps per micrometer. Figure this out by testing or other means. Adjust
#define AXIS5_SLEW_RATE_DESIRED 500 // 500, n, Where n=200..5000 (um/s.) Max microns/second. In DC mode, max pwr % Adjust
#define AXIS5_DRIVER_MODEL OFF // OFF, TMC2130, TMC5160. Leave OFF for all drivers models except these. Option
#define AXIS5_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. For TMC2130, TMC5160. Option
#define AXIS5_DRIVER_IHOLD OFF // OFF, n, (mA.) Current standstill. OFF uses IRUN/2.0. " Option
#define AXIS5_DRIVER_IRUN OFF // OFF, n, (mA.) Current tracking, appropriate for stepper/driver/etc. " Option
#define AXIS5_DRIVER_POWER_DOWN OFF // OFF, ON Powers off the motor at stand-still. Option
#define AXIS5_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option
#define AXIS5_DRIVER_DC_MODE OFF // OFF, DRV8825 for pwm dc motor control on stepper driver outputs. Option
#define AXIS5_LIMIT_MIN_RATE 50 // 50, n. Where n=1..1000 (um/s.) Minimum microns/second. In DC mode, min pwr. Adjust
#define AXIS5_LIMIT_MIN 0 // 0, n. Where n=0..500 (millimeters.) Minimum allowed position. Adjust
#define AXIS5_LIMIT_MAX 50 // 50, n. Where n=0..500 (millimeters.) Maximum allowed position. Adjust
// AUXILIARY FEATURE CONTROL ------------------------------ see https://onstep.groups.io/g/main/wiki/6-ConfigurationMaster#AUXILIARY
#define FEATURE_LIST_DS OFF // OFF, temporarily set ON to list ds18b20 and ds2413 device serial numbers. Adjust
#define FEATURE1_NAME "FEATURE1" // "FE..", Name of feature being controlled. Adjust
#define FEATURE1_PURPOSE OFF // OFF, SWITCH, ANALOG, DEW_HEATER, INTERVALOMETER. Adjust
#define FEATURE1_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust
#define FEATURE1_PIN OFF // OFF, AUX, DS2413, n. Where n is ds2413 s/n (gpio0) or n=0 to 255 (pin#.) Adjust
#define FEATURE2_NAME "FEATURE2" // "FE..", Name of feature being controlled. Adjust
#define FEATURE2_PURPOSE OFF // OFF, SWITCH, ANALOG, DEW_HEATER, INTERVALOMETER. Adjust
#define FEATURE2_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust
#define FEATURE2_PIN OFF // OFF, AUX, CHAIN (ds2413 gpio1,) n. Where n=0 to 255 (pin#.) Adjust
#define FEATURE3_NAME "FEATURE3" // "FE..", Name of feature being controlled. Adjust
#define FEATURE3_PURPOSE OFF // OFF, SWITCH, ANALOG, DEW_HEATER, INTERVALOMETER. Adjust
#define FEATURE3_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust
#define FEATURE3_PIN OFF // OFF, AUX, DS2413, n. Where n is ds2413 s/n (gpio0) or n=0 to 255 (pin#.) Adjust
#define FEATURE4_NAME "FEATURE4" // "FE..", Name of feature being controlled. Adjust
#define FEATURE4_PURPOSE OFF // OFF, SWITCH, ANALOG, DEW_HEATER, INTERVALOMETER. Adjust
#define FEATURE4_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust
#define FEATURE4_PIN OFF // OFF, AUX, CHAIN (ds2413 gpio1,) n. Where n=0 to 255 (pin#.) Adjust
#define FEATURE5_NAME "FEATURE5" // "FE..", Name of feature being controlled. Adjust
#define FEATURE5_PURPOSE OFF // OFF, SWITCH, ANALOG, DEW_HEATER, INTERVALOMETER. Adjust
#define FEATURE5_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust
#define FEATURE5_PIN OFF // OFF, AUX, DS2413, n. Where n is ds2413 s/n (gpio0) or n=0 to 255 (pin#.) Adjust
#define FEATURE6_NAME "FEATURE6" // "FE..", Name of feature being controlled. Adjust
#define FEATURE6_PURPOSE OFF // OFF, SWITCH, ANALOG, DEW_HEATER, INTERVALOMETER. Adjust
#define FEATURE6_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust
#define FEATURE6_PIN OFF // OFF, AUX, CHAIN (ds2413 gpio1,) n. Where n=0 to 255 (pin#.) Adjust
#define FEATURE7_NAME "FEATURE7" // "FE..", Name of feature being controlled. Adjust
#define FEATURE7_PURPOSE OFF // OFF, SWITCH, ANALOG, DEW_HEATER, INTERVALOMETER. Adjust
#define FEATURE7_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust
#define FEATURE7_PIN OFF // OFF, AUX, DS2413, n. Where n is ds2413 s/n (gpio0) or n=0 to 255 (pin#.) Adjust
#define FEATURE8_NAME "FEATURE8" // "FE..", Name of feature being controlled. Adjust
#define FEATURE8_PURPOSE OFF // OFF, SWITCH, ANALOG, DEW_HEATER, INTERVALOMETER. Adjust
#define FEATURE8_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust
#define FEATURE8_PIN OFF // OFF, AUX, CHAIN (ds2413 gpio1,) n. Where n=0 to 255 (pin#.) Adjust
// THAT'S IT FOR USER CONFIGURATION!
// -------------------------------------------------------------------------------------------------------------------------
#define FileVersionConfig 3