Have tou tested?

[Ricky1966]

@Dave811
Maybe I'm wrong , but, I've downloaded your zip and take a look inside BTT config.ini. You have changed NC value of runout sensor, but (and here I don't understand if I have an old one version of GD32 porting) when I've tried, two week ago, to change NC nothing happened, seems we need to change logical of runout (few linea above).
Could you confirming this changing real working?
File is AT-SW-fill-lev.zip
P.S.: what meaning leveling ok? Cause when I've tried the noozle it didn't stop fine and ittrying to "hole" bed!

[Dave811]

I am writing here now, my bed level is working, but I double check in about 2h!

Indeed the config from the TFT needs to be addressed, because you found an issue and my file name isn't scrolling. For the rest I need my PC to look into it.

[Ricky1966]

@Dave811
Ok...fine. I wait for news, I hope good news!
P.S.: I think, but is only my opinion, if you share a guide "how to" for installing new fw for TFT and Marlin, a lot of rockies could try to test all 🤣
For example M502, M500 and so on...

[Dave811]

So a few questions
did you run abl from the tft?
and does the tft give you a warning that the runout sensor was triggered?

[Dave811]

Another question, did you level your bed with a piece of paper?

[Ricky1966]

@Dave811
Yrs with paper.
In my tests it seemed that the BL touch was not working properly. But if I poked him with a finger he would stop. I never understood what the problem was, so after two different Marlins I went back to the stock situation and for now I have only changed the firmware of the TFT.

[Dave811]

So what I did:

1. flash both firmware (tft and marlin)
2. goto: menu -> movement -> leveling
3. do all corners with the paper test until all feel the same
4. goto: menu -> bed level -> p offset
5. do the paper test, so that it feels like the leveling -> click on next and on save
6. goto: menu -> bed level -> abl -> start -> after finish -> save
7. make sure bl: on is there and not bl: off
8. under mesh edit you can see your mesh
9. do a firstlayer print and fine tune the baby steps while its printing, be ready to increase the steps if needed, so that it didn't scratch the bed
10. I use this for the first layer https://teachingtechyt.github.io/calibration.html#firstlayer
11. after the baby stepping do not do the p offset again! Because the baby stepping is done while printing and therefor the right number
12. If you fear, have the finger on the reset button or the power button, so that you can stop the print

[Dave811]

So I thing you problem is the z offset

[Dave811]

I also uploaded a new firmware with a few new settings that I got from prezis thingiverse

[Ricky1966]

@Dave811
Now I'm outside home. When I'll come back tonight I'll try..

[Dave811]

also on my end the run out sensor is working, if the filament runs out, I get an immediate reaction on the display and a few moments later it stops the print

[Dave811]

a small tip, write down your numbers, before you flash, such as the z offset in the baby stepping menu, so after a reflash you can just enter the values before (but make a first layer test befor printing something big, so "only" the bottom left get a scratch if something is not working, the link I sent starts at the bottom left. also Include on the website your slicer start gcode to do a prime line)

[Ricky1966]

@Dave811
I'll doing a M503 with Pronterface, so I'll have all EEPROM settings.
After I'll installing both firmwares.
Only a question,when I've trying, last time, I've saw that the 2 right corners (looking bed in front) was strictly to the bed border right. Are You adjusted this issue?

[Dave811]

@Ricky1966
What do you mean with the 2 right corners? English isn't my first language, so perhabs this is why I dont understand it

[Ricky1966]

@Dave811
Me too.
Last time I've tried firmware, the noozle was placed near the right border (only in manual leveling), and probe was outside bed...I'm explained?

[Dave811]

Do you have a Sidewinder or a Genius Pro?
I don' have the problem, did the printer home before?
then it shouldnt happen

Or did you install any mods that places the BL-Touch elsewhere? (Because I had the issue before, now I am again on the stock SW)

[mikebcbc]

@Dave811 @Ricky1966

Hey guys! Hard to follow this thread. I'm going to install this TFT firmware and freakyguy's marlin firmware to my X2 today. Can you summarize what the known issues are so I can test and report back on my end?

[Dave811]

Just follow this

https://dave811.github.io/ATSG/

[mikebcbc]

Just follow this

https://dave811.github.io/ATSG/

Yes, for sure! I flashed the TFT and it's working great. I was more just asking if you know of any known issues so far that I should be aware of - I saw you and Ricky talking about some issues and wanted to see if there's anything I should know of.

Also, how does your Marlin firmware differ from FreakyDude's? Thanks for working on this.

[Dave811]

It is freakydudes marlin version and this thread is more of a Diskussion at the Moment

[mikebcbc]

For sure! Thanks Dave. I'll report back anything I see as well. Appreciate it!

[Dave811]

@Ricky1966 I need to approve the translation, I can do it later the day, but you need also to translate the first string like Download

[Dave811]

I will close this issue and convert it to a Diskussion, so that nobody gets confused. At the top you can see an item named Diskussion so there will be this thread then

[Ricky1966]

@Dave811
somethings wrong in italian page install, link to download page
Scarica il giusto file da qui: <0>Downloads</0>

[Ricky1966]

@Dave811
Some translation for site (Spanish and Home Page also Italian)

Dopo molto lavoro, svolto principalmente da Gagipro, Ciotto e Fourmi, la Comunità è riuscita ad effettuare il porting del firmware del Display, originalmente concepito dalla BTT per il loro TFT con chip STM32.
Inizialmente la distribuzione delle stampanti Artillery, per i modelli Sidewinder X2 e Genius Pro, avveniva con TFT basati sul medesimo chip, perciò si poteva installare un nuovo firmware, diverso da quello fornito dalla casa madre che rendeva più agevole le impostazioni da parte dell'utente. Verso la metà dello scorso anno il chip del Display, è stato sostituito con un GD32, ciò ha reso fino ad ieri impossibile sostituire il firmware stock con quello BTT.
Come detto dopo molte ore di lavoro e l'aiuto della comunità possiamoora sostituire il firmware di stock delle nostre stampanti, con uno più performante che ci garantisce, senza l'ausilio di software esterni, di accedere a tutte le possibilità offerte dai nuovi Marlin,che via via la comunità stà compilando.
Perciò dopo i diverosi ringraziamenti, vogliamo offrirvi un punto di riferimento per l'installazione del nuovo firmware per il display ed anche un Marlin 2.1.2 compilato ad hoc.
IMPORTANTE!!! QUESTA MODIFICA LA FATE A VOSTRO RISCHIO E PERICOLO, I GESTORI DEL SITO, GLI SVILUPPATORI ED I COLLABORATORI NON RISPONDERANNO IN ALCUNA MANIERA AD EVENTUALI DANNI CHE LA VOSTRA STAMPANTE DOVESSE RIPORTARE!!!

After a lot of work, mainly done by Gagipro, Ciotto and Fourmi, the Community managed to port the Display firmware, originally conceived by BTT for their TFT with STM32 chip.
Initially the distribution of the Artillery printers, for the Sidewinder X2 and Genius Pro models, took place with TFTs based on the same chip, therefore a new firmware could be installed, different from the one supplied by the parent company which made it easier for the user to set up . Towards the middle of last year the Display chip was replaced with a GD32, which made it impossible to replace the stock firmware with the BTT one until yesterday.
As mentioned after many hours of work and the help of the community we can now replace the stock firmware of our printers with a more performing one which guarantees us, without the aid of external software, access to all the possibilities offered by the new Marlins, which the community is gradually compiling.
Therefore, after many thanks, we want to offer you a point of reference for installing the new firmware for the display and also an ad hoc compiled Marlin 2.1.2.
IMPORTANT!!! YOU MAKE THIS MODIFICATION AT YOUR OWN RISK, THE SITE MANAGERS, DEVELOPERS AND CONTRIBUTORS WILL NOT BE RESPONSIBLE IN ANY WAY FOR ANY DAMAGES THAT YOUR PRINTER MAY SUFFER!!!

Después de mucho trabajo, principalmente realizado por Gagipro, Ciotto y Fourmi, la comunidad logró portar el firmware de Display, originalmente concebido por BTT para su TFT con chip STM32.
Inicialmente la distribución de las impresoras Artillery, para los modelos Sidewinder X2 y Genius Pro, se realizaba con TFT basadas en el mismo chip, por lo que se podía instalar un nuevo firmware diferente al suministrado por la casa matriz que facilitaba la usuario para configurar. Hacia mediados del año pasado se reemplazó el chip Display por un GD32, lo que hacía imposible reemplazar el firmware de stock por el BTT hasta ayer.
Como se mencionó después de muchas horas de trabajo y la ayuda de la comunidad, ahora podemos reemplazar el firmware de stock de nuestras impresoras por uno de mayor rendimiento que nos garantiza, sin la ayuda de software externo, el acceso a todas las posibilidades que ofrecen los nuevos Marlins. que la comunidad va recopilando poco a poco.
Por eso, después de muchas gracias, queremos ofrecerle un punto de referencia para instalar el nuevo firmware para la pantalla y también un Marlin 2.1.2 compilado ad hoc.
¡¡¡IMPORTANTE!!! USTED REALIZA ESTA MODIFICACIÓN BAJO SU PROPIO RIESGO, LOS ADMINISTRADORES DEL SITIO, LOS DESARROLLADORES Y LOS COLABORADORES NO SERÁN RESPONSABLES DE NINGÚN MODO POR LOS DAÑOS QUE SU IMPRESORA PUEDA SUFRIR!!

here a translation of other pages in Spanish

DESCARGAS (Download)
Here you can find all the files you need to get your printer running.
Aquì tu puede encontrar todos los archivios que necesita para que su impresora funcione.
You can enter you desired Filter and the table gives you the right download link.
Tu puede entrar los filtros y despues la mesa tedara el archivio da descargar

Instalación

Requisitos:

por ahora :

• una Sidewinder X1 / X2 con sensor de nivel de cama
• una Genius / Pro con sensor de nvel de cama

tarjeta Micro SD

• formatada FAT32
• La tarjeta SD debería funcionar si puede ver el contenido de la tarjeta SD en su impresora 3D, por lo que la mejor opción es ir a (TODO) Imprimir -> cambiar de USB a SD si es necesario -> abrir la tarjeta SD -> deberías ver los archivos
• si no es así, ¡necesita volver a formatear la tarjeta SD o probar una nueva!
• computadora

Preparar

Descarga lo archivio corecto da [Descargar]({% link pages/download.html %}#aux-links)
Por hacerlo utiliza los filtros sobra la mesa
Si tu no sabe el modelo de tus Pantella (TFT), tu debe descargar el archivio DisplayCombo.zip

TFT
Si sabe qué variante de TFT tiene, elija la carpeta correcta que contiene:
TFT más antiguo
Carpeta: TFT28
config.ini
mkstft28.bin
Si tienes el TFT más nuevo
Carpeta:mks_font
Carpeta:mks_pic
Carpeta: TFT28
config.ini
mks_config.txt
mkstft28.bin
mkstft28evo.bin
Luego copie estos archivos y carpetas a una tarjeta SD formateada en Fat32
Coloque la tarjeta SD en su impresora 3D
Si la impresora está en línea
presione el botón de reinicio al lado de la pantalla
Si la impresora está fuera de línea
encienda la impresora
Debería ver "Actualizando..." en la pantalla
Si su pantalla termina de actualizarse, ha terminado con la pantalla (TODO)

Si no sabe qué variante de TFT tiene:
Descargue DisplayCombo.zip y la variante (por ejemplo, Sidewinder o GeniusPro)
Descomprimir ambos zips
En Display Combo, debería ver 3 carpetas que comienzan con un número correspondiente
Comienza con el primero y pon el contenido:
Carpeta: TFT28
config.ini
mkstft28.bin
Una variante puede contener estos archivos:
Carpeta:mks_font
Carpeta:mks_pic
Carpeta: TFT28
config.ini
mks_config.txt
mkstft28.bin
mkstft28evo.bin
en una tarjeta SD que está formateada con Fat32
Si la pantalla se actualiza y puede ver "Actualizando..." en la pantalla
¡Entonces sabrá qué variante de TFT tiene y debe anotarla o recordarla!
Si la pantalla se inicia directamente en el menú Pantalla, debe intentar el mismo proceso con otra carpeta
Si probó las 4 variantes y aún no funciona, comuníquese aquí para obtener ayuda New issue

Marlin

Instale el software STM32CubeProgrammer y ábralo
Conecte su impresora 3D a su PC
Ahora necesita enviar M997 a la impresora
La forma más fácil es usar la pantalla, pero también puede usar pronterface u octoprint
Ir A: "Menú" --> "Terminal"
Introduzca: "M997"
Cambia a tu PC
En STM32CubeProgrammer desde el desplegable "USB" (imagen 1)
Luego haga clic en el botón Actualizar (imagen 2)
Luego haga clic en conectar (imagen 3)
Luego haga clic en el botón "Descargar" (imagen 4)
verifique que la casilla de verificación de programación esté marcada (imagen 5)
Luego seleccione con navegar el firmware en la carpeta marlin (la carpeta extraída del zip descargado) (imagen 6)
Luego presione "Iniciar Programación" (imagen 7)
Y espere hasta que obtenga 2 cuadros de diálogo (imagen 8)
¡Finalmente desconecte la impresora y apáguela!
Si algo salió mal, comuníquese aquí Nuevo problema
Felicitaciones, ya está todo listo :)

[Dave811]

Después de mucho trabajo, principalmente realizado por Gagipro, Ciotto y Fourmi, la comunidad logró portar el firmware de Display, originalmente concebido por BTT para su TFT con chip STM32.

Is this Spanish or Italian?

Dopo molto lavoro, svolto principalmente da Gagipro, Ciotto e Fourmi, la Comunità è riuscita ad effettuare il porting del firmware del Display, originalmente concepito dalla BTT per il loro TFT con chip STM32.

And this is the other then.

I don't know both languages :/

[Dave811]

Thats really great work from your end!!

for the link I need to look into it why it doesn't work.
And after that I add this to the homepage, nice description!

[Ricky1966]

I think is better to adding a after installation for Marlin, with istructions for M502,M500 manual leveling and ABL. I think is better also a PID AUTOTUNE. What do you think about?

[Ricky1966]

Hi @Dave811 , if you add Spanish language, I'll translate also in Spanish

[Dave811]

I will do it

[Ricky1966]

First is Spanish, after Italian. You enable Spanish and the 4 pages, and I translate then!Distinti saluti, Riccardo Bramati -------- Messaggio originale --------Da: Dave811 ***@***.***> Data: 03/04/23 09:51 (GMT+01:00) A: Dave811/ATSG ***@***.***> Cc: Ricky1966 ***@***.***>, Mention ***@***.***> Oggetto: Re: [Dave811/ATSG] Have tou tested? (Discussion #5) Después de mucho trabajo, principalmente realizado por Gagipro, Ciotto y Fourmi, la comunidad logró portar el firmware de Display, originalmente concebido por BTT para su TFT con chip STM32. Is this Spanish or Italian? Dopo molto lavoro, svolto principalmente da Gagipro, Ciotto e Fourmi, la Comunità è riuscita ad effettuare il porting del firmware del Display, originalmente concepito dalla BTT per il loro TFT con chip STM32. And this is the other then. I don't know both languages :/ —Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you were mentioned.Message ID: ***@***.***>

[Ricky1966]

I've also changed some typing errors in italian's pages!Distinti saluti, Riccardo Bramati -------- Messaggio originale --------Da: Dave811 ***@***.***> Data: 03/04/23 09:51 (GMT+01:00) A: Dave811/ATSG ***@***.***> Cc: Ricky1966 ***@***.***>, Mention ***@***.***> Oggetto: Re: [Dave811/ATSG] Have tou tested? (Discussion #5) Después de mucho trabajo, principalmente realizado por Gagipro, Ciotto y Fourmi, la comunidad logró portar el firmware de Display, originalmente concebido por BTT para su TFT con chip STM32. Is this Spanish or Italian? Dopo molto lavoro, svolto principalmente da Gagipro, Ciotto e Fourmi, la Comunità è riuscita ad effettuare il porting del firmware del Display, originalmente concepito dalla BTT per il loro TFT con chip STM32. And this is the other then. I don't know both languages :/ —Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you were mentioned.Message ID: ***@***.***>

[Dave811]

Could we exchange email or phone number?

I mean not here in GitHub, because everyone would see it, but then we could communicate a bit better

[Ricky1966]

You are on Telegram's channel, right?I message you in pvt.Distinti saluti, Riccardo Bramati -------- Messaggio originale --------Da: Dave811 ***@***.***> Data: 03/04/23 10:00 (GMT+01:00) A: Dave811/ATSG ***@***.***> Cc: Ricky1966 ***@***.***>, Mention ***@***.***> Oggetto: Re: [Dave811/ATSG] Have tou tested? (Discussion #5) Could we exchange email or phone number? I mean not here in GitHub, because everyone would see it, but then we could communicate a bit better —Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you were mentioned.Message ID: ***@***.***>