diff --git a/src/app/docs/components/core/page.md b/src/app/docs/components/core/page.md
index 3400f2a..bfb184d 100644
--- a/src/app/docs/components/core/page.md
+++ b/src/app/docs/components/core/page.md
@@ -50,7 +50,7 @@ Insert 2 M3x16 FHCS with M5 washers on the back to stabilize to the carriage.
 
 ### Hardware
 - 2x Belt tubes
-- 2x M3x45 Belt pins of choice (pin or screw)
+- 2x M3x45 Belt pins of choice (pin or screw) (shown in pictures is an allen key, not required)
 
 ### Video Guide
 Soon™
@@ -61,7 +61,7 @@ Your belts should be routed through your gantry at this point, now we're going t
 - Pull your belt through the belt clips.
 - Make a loop and pinch together so that the teeth are locking together.
 - Pull the belt back through the same hole in the clip.
-- Leave enough slack in the previous step, and slide the 4mm OD .tubes through the opening of the loop and through the centre of the clip.
+- Leave enough slack in the previous step, and slide the 4mm OD tubes through the opening of the loop and through the centre of the clip.
 
 {% figure src="/core/core_carriage_belt_clips_tube_a.png" /%}
 {% figure src="/core/core_carriage_belt_clips_tube_b.png" /%}
diff --git a/src/app/docs/components/hotends/page.md b/src/app/docs/components/hotends/page.md
index 3fda4b3..0a7e4a9 100644
--- a/src/app/docs/components/hotends/page.md
+++ b/src/app/docs/components/hotends/page.md
@@ -27,6 +27,6 @@ individual assembly instructions below, or use the video for generic assembly.
     {% quick-link title="Chube - Waterheater" icon="nozzle" href="/docs/components/hotends/chube" description="Chube - Waterheater" /%}
     {% quick-link title="Goliath" icon="nozzle" href="/docs/components/hotends/goliath" description="VZ - Goliath" /%}
     {% quick-link title="Dragon UHF" icon="nozzle" href="/docs/components/hotends/dragon_uhf" description="Phaetus - Dragon UHF/HF/SF" /%}
-    {% quick-link title="VolcMosq" icon="nozzle" href="/docs/components/hotends/volcmosq" description="VolcMosq / MF Crazy / Mosquito" /%}
+    {% quick-link title="VolcoMosq" icon="nozzle" href="/docs/components/hotends/volcmosq" description="VolcoMosq / NF Crazy / Mosquito" /%}
     {% quick-link title="Rapido" icon="nozzle" href="/docs/components/hotends/rapido_uhf" description="Phaetus - Rapido" /%}
 {% quick-links /%}
diff --git a/src/markdoc/partials/microbowden.md b/src/markdoc/partials/microbowden.md
index 8206f30..a7c3977 100644
--- a/src/markdoc/partials/microbowden.md
+++ b/src/markdoc/partials/microbowden.md
@@ -1,6 +1,6 @@
 Push the bowden tube through the opening on the top or bottom, try not to make irreversible kinks while pushing.
 A small flathead or any tool you can fit in the opening of the front may be used to help move the
 bowden along the path. You will need to complete this step a couple of times to get the correct
-measurements/length for your hotend. The easiest way to do this is secure the extruder to the block
+measurements/length for your hotend. The easiest way to do this is secure the extruder to the block and
 push the bowden up through the bottom till it bottoms out. Then take a guess at the length needed
 for your hotend, overestimate it by quite a bit. Now start cutting away until you get a flush fit.